Showing 16 results for Type of Study: Applicable
M. Hosseinzadeh, M. Bozorgmehr, M. Askari,
Volume 36, Issue 1 (6-2017)
Abstract
Cobalt-based amorphous alloys attracted the attention of many researchers to carry out fundamental research for their application in electronics, sensors and magnetic memory due to their special magnetic properties including close to zero Magnetostriction, magnetic permeability and high saturation magnetization. The purpose of this study is the formation and evaluation of microstructure and magnetic properties of cobalt-based amorphous alloy produced by melt spinning and mechanical alloying. The final compositions produced by both methods were studied by scanning electron microscopy, X-ray diffraction and vibrating magnetoresistance. The results showed that compound produced by chill block melt spinning has a better magnetic properties.
M. Illbeigi, A. R. Fazlali, M. Kazazi, A. H. Mohammadi,
Volume 36, Issue 1 (6-2017)
Abstract
In this research, new lithium ion conductor glass-ceramics with NASICON-type structure (Li1+x+yAlxCryGe2-x-y (PO4)3, x+y=0.5) were synthesized using melt-quenching method and converted to glass-ceramics through heat treatment. Influence of addition of different concentrations of aluminum and chromium in LiGe2(PO4)3 glass-ceramic was investigated for ionic conduction improvement. Substitution of Ge4+ ions in NASICON structure by Al3+ and Cr3+ ions induced more Li+ ions in A2 vacant sites to obtain charge balance and also changed the unit cell parameters. These two factors led to ionic conductivity improvement of synthesized glass-ceramics. The glass-ceramics were characterized and the amorth structures were investigated by X-ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Energy-Dispersive X-ray spectroscopy (EDX), Differential Scanning Calorimetry (DSC) and Complex Impedance Spectroscopy (CIS). The highest lithium ion conductivity of 8.82×10-3 S/cm was obtained for x=0.4 and y=0.1 (Li1.5Al0.4Cr0.1Ge1.5(PO4)3) crystallized at 850 oC for 8 h with minimum activation energy of 0.267 eV.
S. R. Hosseini, M. Barati, E. Maghsoudi,
Volume 36, Issue 1 (6-2017)
Abstract
The aim of the present research is calculation and determination of the temperature distribution in the oxy-gas source line heating process for application in the steel plates. Analytical method was used to calculate the temperature distribution by solving mathematical equations. The temperature distribution was determined with numerical method using MATLAB software. A computerized numerical control line heating apparatus was used for carrying out the processes. ITI thermograph camera was used to measure the temperature. The effect of torch distance, gas flow and torch speed on the temperature distribution at the upper and lower surfaces of plate were evaluated. The changes of temperature distribution were achieved at torch speeds of 120, 200 and 300 mm/min, gas flow of 10, 9 and 8 lit/min and torch distances of 30, 40 and 50 mm. Calculated and measured maximum temperatures reached to 900, 810 and 720 K, and 885, 785, 690 K, at torch speeds of 120, 200, 300 mm/min, respectively. The calculated and measured maximum temperatures at gas flow of 10, 9, 8 lit/min are attained to be 900, 810 and 750 K, and 885, 795 and 740 K, respectively. Maximum calculated and measured temperatures at torch distance of 30, 40 and 50 mm are accomplished to be 900, 880 and 810 K and 885, 840 and 790 K, respectively.
H. Ahmadi, S. Otroj, M. R. Nilforushan, A. Dehghani Varnamkhasti,
Volume 36, Issue 2 (9-2017)
Abstract
In this study, the composition of magnesium aluminate spinle and the converter mud were used as raw materials to in-situ formation of hercynite phase in magnesite-hercynite refractory bricks. The pressed samples were sintered at 1400 and 1500℃ and then, the phase composition of bricks was evaluated after firing at 1400℃. Besides, the effect of nano-magnesia particles addition on the properties of magnesia-hercynite refractory bricks was examined. Hence, the physical peroperties, thermal shock resistance and microstructure of refractory bricks were evaluated. The phase composition results showed that hercynite is well-formed in the refractory matrix, which leads to bonding formation and its increase between magnesia particles. The evaluation of results indicated that the addition of nano-magnesia particles can reduce the porosity of brick via increasing particles packing. In this relation, 1 wt. % nano-magnesia addition was determined as optimum content. Further addition of nano-magnesia leads to increasing of porosity via agglomeration of particles. Due to the high surface area of used nano-magnesia particles, the adequate sintering of refractory brick containing nano-magnesia take places at 1400℃. This leads to increasing of particles bonding and then, increasing mechanical strength, but it can not affect the thermal shock resistance of refractory bricks. The microstructural evaluations showed the lower porosity and further particles bonding with addition of nano-magnesia optimum content.
M. Hosseinzadeh, M. Bozorgmehr, A. Ghasemi, M. Askari,
Volume 37, Issue 2 (9-2018)
Abstract
NdFeB magnetic alloy is one of the hard magnets having the highest maximum energy in the world. The most popular methods of manufacturing magnetic alloys Nd2Fe14B are powder metallurgy and rapid quenching techniques. In this research, the effect of the hot press temperature on the magnetic properties of the hard magnet Nd2Fe14B was studied. Structural studies were carried out using X-ray diffraction, X-ray fluorescence spectrometer and Scanning Electron Microscope; Spectroscopic energy distribution of Nd2Fe14B bulk magnet and the magnetic tests were done using a vibrating magnetometer to investigate the structures and the magnetic properties of the produced samples. The results showed that in addition to the Nd2Fe14B phase, the α-Fe and Nd-rich phase also existed in the structure of the provided magnet. These secondary phases had effectively created exchange couplings with the main phase, improving the magnetic properties. The magnetic properties of the sintered magnets were improved by increasing the press temperature; finally, Nd2Fe14B magnet was made with the maximum energy, which was d higher than 290 kj/m3 .
M. Hajfarajzadeh, A. Eshaghi, A. Aghaei,
Volume 37, Issue 4 (3-2019)
Abstract
A TEOS-GPTMS nano-hybrid thin film was deposited on the polymethyl methacrylate (PMMA) substrate by a sol-gel dip coating method. Morphology, roughness and surface chemical bonding of the thin films were evaluated by X-ray diffraction (XRD), field emission scanning electron microscopy(FE-SEM), atomic force microscopy, and Fourier transform infrared spectroscopy methods, respectively. UV-vis spectrophotometer was used to measure the transmittance spectra of the samples. Also, the adhesion and hardness of the coatings were investigated using pencil hardness the adhesion tape test and the test, respectively. XRD results proved that the thin film had an amorphous structure. Also, FE-SEM images indicated that addition of GPTMS to the TEOS yielded a crack-free thin film. Based on the UV-vis spectroscopy results, the transmittance of the polymer substrate in the visible region was increased by the deposition of the nano-hybrid coating. Moreover, the hardness of the PMMA substrate was increased from 3H to 6H by the deposition of the nano-hybrid thin film. Also, tape test confirmed the high adhesion of the nano-hybrid thin film on the PMMA substrate. Consequently, the transparent organic-inorganic GPTMS-TEOS hybrid coating can be used as a scratch resistant coating on the PMMA substrate.
F. Saeidpour, M. Zandrahimi, H. Ebrahimifar,
Volume 38, Issue 1 (6-2019)
Abstract
Crofer 22 APU ferritic stainless steel has been evaluated as one of the favorable materials for utilization in Solid oxide fule cell (SOFC) interconnects. However, there are difficulties in utilizing these metallic interconnects, including the quick decrease of their electrical conductivity and evaporation of Cr species. To overcome the above problems, the application of protective coatings has been proposed. In this work, Co/Y2O3 composite coatings were deposited onto Crofer 22 APU stainless steels by direct current electrodeposition method. Oxidation and electrical properties of uncoated and coated steels were evaluated. Surface and cross-section of the bare and coated steels were characterized using scanning electron microscopy and X-ray diffraction techniques. Results showed that oxidation rate of the coated specimen was reduced by about 4 times, as compared to the uncoated one after 500 h isothermal oxidation in air at 800˚C. Formation of Co3O4 and MnCo2O4 spinel compositions improved electrical conductivity of the coated sample. After 500 h of isothermal oxidation at 800˚C, ASR value of the Co/Y2O3-coated and uncoated steels was 15.8 mΩ·cm2 and 25.9 mΩ·cm2 , respectively.
H. Esfahani, M. Rasouli Samar, F. Dabir, A. Abdollahzadeh,
Volume 38, Issue 1 (6-2019)
Abstract
In this study, mechanism and kinetic of formation of boride layer on In-738 superalloy were investigated via diffusion pack cementation method. Boriding was carried out at 900 °C for several short times (5, 15, 45 and 60 min). Phase study by means of X Ray defragtion (XRD) indicated that in addition to Ni3B, other phases such as Cr5B3, AlB2, and W2B were formed at the first period of process, and other compounds such as MoB2, VB, TiB, Ni6Si2B, and Mo2NiB2 were generated in the more prolonged time. SEM study also showed that not only the thickness of boride coating was increased, but also an interdiffusion zone (IDZ) was formed under the coating and it was grown by the upward diffusion of alloy elements. The kinetic study was good according to diffusion theory, confirming the two diffusion steps for IDZ. Thickness and hardness of the boride coating over 60 min process were 27.8 µm and 853 HV, respectively.
M. Eshraghi, Z. Mosleh, M. Rahimi,
Volume 38, Issue 1 (6-2019)
Abstract
In this investigation, the structural and magnetic properties of Cr and Zn substituted Co ferrite with the general formula Co1-xZnxFe2-xCrxO4 (x= 0.1, 0.3, 0.5, 0.7) as prepared by sol- gel method were studied. The structural, morphological and magnetic properties of the samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Scanning electron microscopy (SEM) and Vibrating sample magnetometer (VSM). XRD measurements along with the Rietveld refinement indicated that the prepared samples were single phase with the space group of Fd-3m. Results of SEM images also showed that the particles were in the nanosize range. Also, the magnetic properties of the samples indicated that the magnetization was first decreased, reaching the minimum value for x=0.1 sample; then it was increased. This behavior was related to the cation distribution at the tetrahedral and octahedral sites. Moreover, coercivity was significantly decreased with increasing the doping level due the decrease of magnetocrystalline anisotropy because of the nonmagnetic Zn ion substitution.
H. R. Shahverdi, R. Alipour Mogadam,
Volume 38, Issue 2 (9-2019)
Abstract
Creep age forming (CAF) process is a novel metal forming method with major benefits including improved mechanical properties and cost reduction for aviation industry applications. CAF happens due to creep phenomenon and stress-release during the artificial aging of heat-treatable aluminum alloys. In this work, the creep age forming of 7075 Aluminum alloy at 120, 150 and 180 °C for 6, 24 and 48 h was done; tensile and hardness tests were used to characterize the samples. Results on spring-back revealed that it was influenced by time and temperature; by increasing the time and temperature, it was reduced from 54.1 to 39.51. Mechanical property evaluation also showed that by increasing the time, the strength and hardness could be enhanced due to microstructural evolution and precipitation during the CAF process. According to the mechanical and CAF results, two samples were selected as the optimum ones and their work hardening behavior and fracture surfaces were investigated
M. Samii Zafarghandi, S. M. Abbasi,
Volume 38, Issue 2 (9-2019)
Abstract
In the present work, hot tensile behavior of Haynes 25 Co-base alloy was investigated in the temperature range of 950-1200 ˚C and 0.1 s-1. Thermodynamic calculations showed that M23C6 and M6C carbides were stable below 1000 ˚C and above 1050 ˚C, respectively. Stress-strain curves also indicated an unusual trend of strain fracture. It was observed that with increasing temperature from 950 to 1050 ˚C, the fracture strain was decreased, while it was raised above 1050 ˚C again. Increasing the volume fraction of M6C carbide rich in Tungsten resulted in the loss of ductility. Also, microstructural evaluations showed dynamic recrystallization (DRX) grains were nucleated and growth was around carbides and the initial grains at 1150 ˚C. Occurrence of DRX led to the improvement of ductility via grain refinement mechanism, so this alloy had the highest level of ductility at 1150 ˚C
M. Emami, Sh. Hayashi,
Volume 38, Issue 3 (12-2019)
Abstract
The outer surface of heat exchanger tubes that work under fluidized bed waste or biomass incineration is exposed to severe high-temperature erosion-corrosion (E-C). To evaluate the behavior and enhance the service life of the tubes, the real service conditions ought to be simulated in the laboratory. In this study a test rig with a fluidized bed of hot sand was designed and manufactured to expose nickel-based SFNi4 alloy to high-temperature E-C. In order to increase the corrosiveness of the environment, the silicon oxide sand was mixed with 0, 0.5 and 1 wt.% of a mixture of NaCl and KCl salts with 1:1 molar ratio. The erosive conditions of the environment were changed by altering air flow rate from 20 to 25 L/min and changing the sand incident angle from 45 to 90 degrees. The rate of material removal was calculated by measuring the thickness of each sample before and after the test. After each experiment, the surface and cross-section of specimens were studied using SEM and EDS analysis. Finally, the optimum E-C parameters to ensure actual industrial conditions were obtained.
R. Moradi, M. Roshanaee, H. Mostaan, F. Nematzadeh, M. Safari,
Volume 40, Issue 1 (5-2021)
Abstract
In this research, microstructure and mechanical properties of laser welded joints between 2304 duplex stainless steel and Inconel 718 nickel-based super alloy were investigated. Microstructural evolution in the various areas of welded joints and also the effect of welding parameters on the mechanical properties of dissimilar joints were studied. Response surface methodology based on the central composite design was used in order to find the optimum welding parameters. Effective parameters of the welding process including laser power, travel speed and defocusing distance were set in the range of 1000 to 1900 W, 1 to 5 mm/s and -1 to 1 mm, respectively. Uniaxial tensile test was used to evaluate the fracture force of weld joints. The microstructural observations and phase evolutions were studied using optical microscope. It was found that the fracture force of the weld joints firstly increased by travel speed and defocusing distance and then decreased by further increase. The maximum fracture force was obtained when laser power, travel speed and defocusing distance were 1900 W, 3 mm/s and 0 mm, respectively. The center line of weld metal was mainly consisted of equiaxed grains where, columnar grains were formed in the fusion line. The obtained results from the hardness measurement showed that the hardness of Inconel 718 was decreased due to dissolution of TiC and NbC particles.
N. Ghobadi, S. A. Hosseini Moradi, M. Amirzade,
Volume 40, Issue 4 (3-2022)
Abstract
In this research, cobalt ferrite powders (CoFe2O4) and cobalt ferrite/reduced graphene oxide composite (CoFe2O4/RGO) were synthesized by the co-precipitation method. The phase structure, morphology, magnetic properties, and microwave absorption properties of the produced samples were investigated through various techniques. X-ray diffraction test indicated the successful formation of pure CoFe2O4 and its composites with RGO. According to the Scanning electron microscopy (SEM) images, most pure and composite samples’ particles were formed in a semi-spherical shape. The VNA test results showed the saturation magnetization of CoFe2O4 and the composite containing 5 wt.% and 10 wt.% of RGO, 71.6, 56, and 37 emu/g, respectively. Also, the network analyzer results demonstrated the maximum reflective losses in the X-band range due to the impact of microwaves on CoFe2O4 te was -5.5 db. This amount reached 21.5 dB with the addition of 10 wt.% RGO. Also, the wave input increased from 41% for the pure CoFe2O4 to 99.5% for the sample containing 10 wt.% RGO.
S. H. Hashemi Rizi , A. Nourmohammadi Abadchi,
Volume 40, Issue 4 (3-2022)
Abstract
Development of materials with the ideal black body absorption spectrum are of great interest. Such materials could improve the efficiency of solar cells, and passive cooling and heat transfer systems as well as the protective and decorative coatings. Fabricating black anodizing coatings is promising for this purpose because they exhibit low light reflection from the surface. Such coatings can be produced through successive anodizing and black coating of aluminum alloys. In this study, the effect of anodizing repetition on the absorption coefficient of the black anodizing coatings on 2024 aluminum alloy was investigated, as model. All the parameters were fixed in the black coloring stage to evaluate the influence of the anodizing steps. After a one-step anodizing, the black coatings showed an absorption coefficient of 0.956 in the visible region and 0.911 in the of 220 to 2200 nm wavelength range, while their absorption coefficient increased after a three-step anodizing up to 0.982 in the visible region and up to 0.966 in the 220 to 2200 nm wavelength range. This indicates that anodizing repetition helps the optical absorption of black anodizing coatings to approach the optical absorption of an ideal black body.
Sh. Talebniya, M. R. Saeri, I. Sharifi, A. Doostmohammadi,
Volume 41, Issue 1 (8-2022)
Abstract
Magnetic nanoparticles are of interest in various research fields such as magnetic fluids, catalysts, biotechnology, medicine, information storage, and environmental issues. However, spinel ferrite magnetic nanoparticles with proper magnetic properties could not be used alone in these applications because of their lack of biocompatibility and instability in aqueous solutions. Surface coating is an effective strategy to eliminate or minimize this issue. In this study, FeFe2O4 and ZnFe2O4 spinel ferrites were synthesized using the reverse co-precipitation method under a nitrogen gas atmosphere. The magnetic behavior of the particles, determined by a vibrating magnetometer (VSM) showed the saturation magnet (Ms) values of the FeFe2O4 and ZnFe2O4 spinel. Fourier-transform infrared (FTIR) spectra showed two high-frequency bands v1 and v2 at about 554-578 and 368-397 cm-1, respectively, which were related to the spinel structure. Finally, the synthesized FeFe2O4 nanoparticles were coated with chitosan and polyethylene glycol (PEG) biopolymers. The TEM and FTIR analysis indicated that the magnetic nanoparticles were uniformly coated by the biopolymers.
