Showing 7 results for Kharaziha
M .kharaziha, M.h. Fathi,
Volume 29, Issue 1 (Jun 2010)
Abstract
In this study, forsterite nanopowder was prepared by mechanical alloying and post-heat treatment method. Bioactive properties of forsterite nanopowder were studied by immersing the powder in the SBF. Nanostructure forsterite bulk dense form was prepared by the two step sintering method. It was found that pure forsterite nanopowder with 25-60nm particle size was produced. The results of soaking of forsterite nanopowder in the SBF showed that forsterite nanopowder is bioactive. Also, forsterite dense bulk with the optimal hardness of 940 Hv and fracture toughness of 3.61 MPa.m1/2 was produced. These findings suggest that forsterite nanostructure ceramics possess good biocompatibility, bioactivity and mechanical properties and could be suitable for orthopedic and dental implant materials.
Z. Khosroshahi, F. Karimzadeh, M. Kharaziha,
Volume 37, Issue 2 (Journal of Advanced Materials-Summer 2018)
Abstract
Due to electrical properties (high electron mobility) and electrochemical characteristics (high electron transport rate), graphene-based materials have been widely applied for various scientific fields. However, due to their two-dimensional structures, these materials have low active sites for reaction. Therefore, changing from two-dimensional sheets dimensional to the three-dimensional ones could provide graphene-based materials with high specific surface and electron and mass transport particles. For these purpose, reduced graphene oxide (rGO) and polystyren (PS) aqueous solution were mixed with two different weight ratios kinetic. In this study, the three-dimensional graphene (3DG) was synthesized with graphene oxide using sacrificial PS particles. For this purpose, rGO and the PS aqueous solution were mixed with two different weight ratios of 95:5 and 85:15. Then, the 3DG-PS scaffolds were synthesized by controlling the pH value in the range of 6-8. Subsequently, PS particles were removed by immersing the synthesized scaffolds in toluene. In this research, the effect of filtering through the member filter and centrifuge on the morphology of the scaffolds was investigated. The scaffolds were characterized with X-ray diffraction and scanning electron microscopy. The results showed the formation of 3DG with a uniform distribution of porosities by using the centrifuge procedure. Moreover, the sacrificial PS particles were completely removed when the rGO to PS weight ratio was 95:5. So, 3DG with the uniform distribution of microscopy porosity could be synthesized through the sacrificial mold method and the centrifuge procedure; graphene oxide was also reduced with the PS weight ratio of 95:5. Further, based on the electrochemical evaluation of this optimized sample, as compared to the rGO , it was found that the 3DG had better electrochemical properties than the rGO. Therefore, 3DG with the optimized rGO to PS weight ratio of 95:5 could be an ideal substitute for rGO in electrochemical applications
Sh. Tavakoli Dehaghi, S. Darvishi, Sh. Nemati, M. Kharaziha,
Volume 37, Issue 3 (Journal of Advanced Materials-Fall 2018)
Abstract
Abstract: With the advances in the development of biomaterials for tissue replacement, the attention of scientists has been focused on the improvement of clinical implant properties. In this regard, despite the appropriate properties of the stainless steel, the application of stainless steel as implants has been limited due to the weak corrosion resistivity. The purpose of this paper was preparation and characterization of hydrophobic polydimethylsiloxane (PDMS)-SiO2-CuO nanocomposite coating on the 316L stainless steel surface. The 316L stainless steel was coated by SiO2 nanoparticles (20 wt. %), CuO nanoparticles (0.5, 1 and 2 wt. %) and biocompatible PDMS. In this research, x-ray diffraction (XRD) and scanning electron microscopy (SEM) were applied to characterize the coating. Moreover, the roughness and water contact angle of the coatings consisting of various amounts of CuO nanopowder were estimated. Finally, the effects of various amounts of the CuO nanopowder on the corrosion resistivity of nanocomposite coatings were investigated. XRD patterns confirmed the presence of crystalline CuO nanoparticles on the substrate. Due to the non-crystalline nature of silica nanoparticles and the semi-crystalline PDMS polymer, no peak confirming the presence of these phases was detected on the XRD pattern of the nanocomposite coating. SEM images showed the formation of a lotus leaf-like layer on the surface of the nanocomposite coating containing 1 and 2 wt. % CuO. Moreover, water contact angle evolution revealed that while contact angle was 81 degree without CuO nanoparticles, it was enhanced to 146 degree in the presence of 1 wt. % CuO. Moreover, the corrosion study showed the nanocomposite containing 2 wt.% CuO had the best corrosion resistance, the corrosion current density of 2.1E-7 A.cm-2, and the corrosion potential of 0.22 V.
N. Safari, M. Toroghinejad, M. Kharaziha, V. Saeedi,
Volume 38, Issue 3 (Journal of Advanced Materials-Fall 2019)
Abstract
The aim of this study was to fabricate the Mg-1Al-Cu alloys with various amounts of Cu content (0, 0.25, 0.5 and 1 wt.%) using spark plasma sintering (SPS) approach and evaluation of their degradation rate and biological properties. The results indicated that Cu incorporation (0.25 wt.%) significantly diminish degradation rate from 0.039 cm/h in pure Mg to 0.00584 cm/h in Mg-1Al-0.25Cu alloy. In addition, Mg-1Al-0.25Cu alloy could noticeably (1.25 times) promote viability of MG63 cells compared to pure Mg, owing to the optimized ion release. Moreover, the antibacterial activity of Mg-1Al-0.25Cu was considerable. In summary, Mg-1Al-0.25Cu alloy with appropriate degradation rate, good biocompatibility and antibacterial properties can be introduced as a biodegradable orthopedic implant.
N. Bahremandi Tolou, H. R. Salimi Jazi, M. Kharaziha, N. Lisi, G. Faggio, A. Tamburrano,
Volume 39, Issue 1 (Journal of Advanced Materials-Spring 2020)
Abstract
In recent years, graphene has been considered in various tissue engineering applications such as nerve guide conduits because of its unique properties such as high electrical and mechanical properties, porous structure for exchange of nutritious and waste materials, biocompatible, capability of drug and growth factor delivery. In the current study, nerve guide conduits based on a 3D graphene were synthesized by induction heating chemical vapor deposition (ICVD). Graphene was synthesized on Ni foam template at 1080 ͦC. Fabricated samples were characterized by Raman analysis and Scanning Electron Microscopy. Raman analysis showed that the synthesized graphene is in the form of a turbostratic multilayered graphene with little defects. Cyclododecane (CD) as a temporary protective layer was used to remove nickel. After removing nickel, the free-standing 3D-graphene structure was coated with a polymer (PCL) by drop and dip coating methods to obtain the composite conduit. A comparison of the electromechanical results of the 3D-graphene/PCL conduit and PCL conduit indicated that firstly, grapheme increased the electrical conductivity of the composite conduit which will help promote nerve regeneration and axon growth. Secondly, tensile strength and flexibility of the 3D-graphene/PCL conduit was improved compared to the PCL conduit.
N. Zakeri, H.r. Rezaie, J. Javadpour, M. Kharaziha,
Volume 39, Issue 4 (Journal of Advanced Materials-Winter 2021)
Abstract
In recent years, nanoceramics have been used in scaffolds to emulate the nanocomposite with a three-dimensional structure of natural bone tissue. In this regard, polycaprolactone biopolymer is widely used as a scaffold in bone tissue engineering. The goal of this research is to produce porous scaffolds of polycaprolactone - zeolite biocomposite with suitable mechanical, bioactive and biological properties for bone tissue engineering applications. The nanocomposite scaffolds were synthesized by solvent casting/particulate leaching and freeze-drying approaches. Microscopic investigations showed generation of pores with an average size of 200-400μm after addition of ceramic phase. Energy dispersive X-ray analysis confirmed uniform distribution of ceramic phase in polycaprolactone matrix. FTIR results determined the binding type of zeolite nanoparticles to the polycaprolactone matrix as physical bonding. The results of mechanical tests showed the increase in young’s modulus after addition of ceramic phase (from 0.04 to 0.3 and 3 to 7 MPa, respectively). The hydrophilicity of polycaprolactone increased after adding nanozeolite and more weight loss was observed for scaffold containing 20% zeolite (53.52 6 1.6%) with an increase in the rate of hydroxyapatite formation. The results showed that the prepared scaffolds have potential for cancellous bone tissue engineering application.
R. Bagheri, F. Karimzadeh, A. Kermanpur , M. Kharaziha,
Volume 40, Issue 2 (Journal of Advanced Materials-Summer 2021)
Abstract
A new method has been presented for the synthesis of copper (Cu)/copper oxide (CuO)-nanoparticles (NPs), based on the process of corrosion and oxidation of Cu-NPs on the surface of the gold electrode by nitric acid. Cu-NPs were deposited on the surface using potentiometric method. The high concentration of Cu-NPs was estimated by Differential Pulse Voltammetry (DPV). The process of growth and distribution of CuO-NPs on the surface of Cu-NPs using structural analysis of Fourier Transform Infrared Spectroscopy (FTIR) and X-ray diffraction (XRD) showed that nitrate was well absorbed and a sharp hydroxyl peak appeared and a phase of CuO NPs formed on the electrode surface. The surface morphology indicated that the average size reduced from about 150 nm to 50 nm in the presence of nitrate. This can be due to the oxidation of Cu nanoparticles on the surface and reduction of particle size compared to the absence of nitric acid. This simple and low-cost method can be used as a surface modification of antibacterial and active catalyst electrodes.
