Showing 4 results for M. Alizadeh
M. Alizadeh and H. Edriss,
Volume 21, Issue 2 (1-2003)
Abstract
In recent years many different ways have been investigated by steel producers to increase ductility, impact strength and formability of steels. More important ways are steels with very low amounts of inclusion, small size inclusions and modified inclusions. In this study, experiments have been performed on the API-X42 steel produced by the electric arc furnace in Mobarekeh Steel Co. After the preparation of the melt in the electric arc furnace, it is taped in a 200-ton ladle and ladle treatment was preformed in a ladle furnace (LF) in the steelmaking shop. In this study the effects of amount and the rate of CaSi wire addition on the shape and structure of inclusion were investigated. The optimum conditions for adding CaSi for inclusion shape control were also determined. Scanning electron microscope (SEM) and chemical energy analysis dispersive system (EDS) showed that adding calcium to the melt affects the chemical composition of inclusions present in steel melt. The effects of CaSi wire injection treatment, injection amount and inclusion shape control on the impact property and formability of steel were shown using charpy impact test.
Keywords: Inclusion shape control, calcium treatment, ladle furnace and inclusion modification
M. Alizadeh, H. Edris, and A. Shafyei,
Volume 27, Issue 2 (1-2009)
Abstract
M. Talebian, M. Alizadeh, M. Ehteshamzadeh,
Volume 33, Issue 2 (Journal of Advanced Materials-fall 2015)
Abstract
In this study, Al/Steel multilayer composite was produced by accumulative roll bonding (ARB) process using Al-1100 and St-12 strips. Microstructure, mechanical properties and corrosion behavior of the composite were studied by scanning electron microscopy (SEM), tensile test, Vickers microhardness tests, cyclic polarization and electrochemical impedance spectroscopy (EIS) measurement in 3.5 wt% NaCl solution. After one ARB cycle (2 roll-bonding cycles), the multilayer composite of 4 layers of Al and 2 layers of steel was produced. The tensile strength of the Al/steel multilayer composite reached 390.57 MPa after the first ARB cycle, which was 1.29 times larger than that of the starting steel while composite density was almost half the density of the steel. Corrosion behavior of the composite revealed a considerable improvement in the main electrochemical parameters, as a result of enhancing influence of cold rolling. The results indicated that strength and corrosion resistance of Al/steel composite generally decreases and elongation increases after annealing.
Z. Ansari, M. Alizadeh, A. Sadeghzadeh Attar,
Volume 33, Issue 2 (Journal of Advanced Materials-fall 2015)
Abstract
In this study, mixed metal oxides Al2O3/MgO/TiO2 coatings with Al/Mg/Ti ratios of 5:1:3 and 2.5:3:4 were coated on AA1100 aluminum by sol-gel method. The surface morphology, phase analysis and the corrosion behavior of the Al2O3/MgO/TiO2 coatings were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), and electrochemical impedance spectroscopy measurements (EIS) in 3.5 wt.% NaCl solution. The thermal behaviors, the bonds configuration, and functional groups of the coated samples were studied by thermo-gravimetric and differential thermal analysis (TG-DTA) and Fourier transform infrared spectroscopy (FTIR), respectively. The results demonstrated that heat treatment at
450 °C caused an increase in porosity and coating cracking, finally leading to the decrease of corrosion resistance. The best corrosion resistance was achieved for the sample with Al/Mg/Ti molar ratio of 5:1:3 without any heat treatment. The structure of this sample was amorphous, and heat treatment resulted in crystallization and decrease of the corrosion resistance.
