Showing 18 results for Mohammadi
A. R. Azimian and S. Mohammadivand,
Volume 18, Issue 2 (7-1999)
Abstract
A. H. Shirmohammadi,
Volume 19, Issue 2 (1-2001)
Abstract
The present study is intended to develop a Preventive Maintenance (PM) policy for industrial applications, while considering two different objectives: the first objective is to optimize the total maintenance costs, i.e., the Preventive Maintenance (PM) and Emergency Maintenance (EM) Costs Per Unit Time. (CPUT). The second objective is to design the policy in such a way that the simplicity of its application in a production industry environment is improved.
A simulation model is constructed and, using a Monte Carlo simulation, the model is run for a sufficient number of cycles in order to determine the optimum value of a decision parameter (TX). The TX value provides the PM planning section with the possibility of economically postponing the PM action to its next scheduled date. Numerical examples are given to show the validity of the model and comparisons are made with existing PM policies in industry and in the literature to evaluate the cost reduction values that can be obtained through the adoption of the policy, while the implementation simplicity is also maintained
M. Khan-Mohammadi and M. S. Marefat,
Volume 25, Issue 1 (7-2006)
Abstract
To assess the performance criteria of the reinforced-concrete, five-storey residential buildings common in Iran, an
experimental study in the structural laboratory of the University of Tehran has been conducted. The test program includes cyclic and monotonic load tests of six beams that represent three-to-five storey buildings with rigid frame structures. Using definitions given in FEMA-356 and ATC-40, stages of immediate occupancy, life safety, and collapse prevention have been identified on the drift- force curves of all specimens. Based on the test results, values of the plastic rotation, ductility, strain in concrete cover and in longitudinal bar, crack width, damage index, and length of plastic region at different levels have been determined. It was found that the recommended values of plastic rotation and ductility for reinforced concrete beams by FEMA-356 are conservative. The length of plastic hinge region in the stage of immediate occupancy is about half the plastic hinge length in the stage of life safety and it increases by 20% from life safety to collapse prevention
H.a. Abyaneh, R. Mohammadi H. Torkaman, F. Razavi, and E. Afjei,
Volume 27, Issue 2 (1-2009)
Abstract
All algorithms for impedance calculation use an analog-to-digital converter. The high accuracy of the impedance seen by a distance relay is an important factor in the correct isolation of the faulty part of power systems. To achieve this, a novel
technique based on third order interpolation is used in this paper. According to this technique, the times and the values of the obtained samples are changed to real ones. To evaluate the new technique, it is applied to six digital distance algorithms, namely, Discrete Fourier Transform (DFT), Half-cycle Discrete Fourier Transform, Least Square, Mann-Morrison, Least Square with Delete Dc, and Prodar70. The technique is found to be capable of accurately computing the impedance in the algorithms mentioned. Comparisons are made among the results to show the efficiency of the new technique for decreasing errors in all algorithms.
S. Otroj, F. Mohammadi, M.r. Nilforushan,
Volume 33, Issue 1 (Journal of Advanced Materials- Summer 2014)
Abstract
In this paper, the effect of MgCl2 addition on the kinetics of MA spinel formation was investigated. For this purpose, the stoichiometric mixture of MgCO3 and calcined aluminum was calcined at 1100 °C for 1 hr. Then, the calcined composition was wet-milled and after addition of 6% MgCl2 the compositions were pressed and fired at 1300 and 1500 °C for different times. Spinel phase content was determined using semi-quantitative phase analysis. With regard to Jander's equation, the rate constant was calculated, and the activation energy was obtained from Arrhenius equation. The results showed that the addition of MgCl2 leads to the acceleration of the spinel formation reaction. Besides, 55.71 Kcal/mol as the activation energy was calculated for the composition containing 6 wt.% MgCl2 compared with 93.06 Kcal/mol for the composition without MgCl2.
S. Mohammadi, A. Doostmohammadi, M.r. Saeri,
Volume 34, Issue 1 (Journal of Advanced Materials-Spring 2015)
Abstract
The positive effect of Si and Zn ions on bone formation and metabolism has already been confirmed. The aim of this study was preparation and characterization of Willemite (Zn2SiO4) for the repair of bone defects. Willemite was prepared through solid state reaction. Phase analysis and chemical compositions were investigated. The zeta potential of the nanoparticles was determined in physiological saline, and compressive strength and Young's modulus of the samples were measured. The ability of hydroxyapatite formation was investigated in simulated body fluid (SBF) and cytotoxicity of the particles was evaluated in contact with human bone marrow stem cells. The results of this study showed that Willemite nanobioceramic is obtained with the expected chemical composition and negative zeta potential. The results also showed that the hydroxyapatite forming ability in SBF was not strong. MTT assay confirmed the cell proliferation and availability in contact with a specific concentration of Willemite nanoparticles. All these findings indicate that Willemite nanobioceramic with proper biocompatibility can be suggested as a novel biomaterial for the repair of bone defects.
S. Yazdkhasti, A. Monshi, A. Doostmohammadi,
Volume 34, Issue 4 (Journal of Advanced Materials-winter 2016)
Abstract
With various features such as strong oxidation, biocompatibility and acceptable mechanical properties, titanium dioxide (TiO2) is among the materials that are frequently used in biological and medical applications. Nowadays, with the aim of increasing the efficiency of titanium dioxide and practical use of this material, doping it with elements such as silver, zinc and iron has been favored. In this study, Ag-TiO2 and ZnO-TiO2 nanoparticles were prepared by the sol–gel method and were evaluated and compared.In order to identify the present phases in the structure, X-ray diffraction analysis was used. Also for the characterization of the nanoparticles, Ultraviolet–visible spectroscopy (UV-Vis), Energy-dispersive X-ray spectroscopy (EDS), Field Emission Scanning Electron Microscope (FESEM) and Zeta Potential were used. Inaddition, the antibacterial activities of nanoparticles were investigated and compared. The results showed that sol-gel method could successfully produce nanoparticles of Ag-TiO2 and ZnO-TiO2 with the expected combination. The investigation of antibacterial properties of these particles revealed that at lower inhibitory concentrations, Ag-TiO2 composition has a higher antibacterial activity than ZnO-TiO2 one.
A. Abdolahi, M. R. Saeri, F. Tirgir, A. Doostmohammadi, H. Sharifi,
Volume 35, Issue 1 (Journal of Advanced Materials-Spring 2016)
Abstract
In this study, NBG was successfully achieved through a sol-gel technique, and to further improve its dispersibility, a crylate coupling agent was coupled onto the surface of the NBG. The 3-(Trimethoxysilyl)Propylmethacrylate coupling agent was used to the surface modification of the synthesized NBG by a wet-chemical method in a dynamic inert nitrogen atmosphere. The surface properties of the biomaterials before and after modification were characterized and compared using FTIR and AFM techniques. The characteristic peaks in FTIR spectra indicated that –CH2, –CH3 and C=O groups appeared on the surface of modified NBG, and also, AFM analysis revealed that the dispersibility of surface modified NBG was improved, significantly. The above results proved that the desired groups of 3-(Trimethoxysilyl)Propyl methacrylate had been covalently bonded onto the surface of NBG. Besides, a nanocomposite scaffold was synthesized using the synthesized NBG and polyurethane foam as raw materials. The morphology of pores, porosity contents, compress strength and bioactivity of the scaffold were studied. The results showed that the biological scaffolds for use in bone tissue engineering with the basic requirements (90% porosity and 200-600 μm pore diameter) were successfully prepared. The polymer component had no effect on the relationship between the scaffold pores and bioactivity of bioglass nanoparticles. Improvement of compressive strength and proper bioactivity of the resulted scaffold showed that it is an acceptable candidate for biomaterials applications.
S. Nikbakht Katouli, A. Doostmohammadi, F. Esmaeili,
Volume 35, Issue 1 (Journal of Advanced Materials-Spring 2016)
Abstract
The aim of this study was to fabricate carbon nanotube (CNT) and bioactive glass nanoparticles (BG) (at levels of
5 and 10 wt%) incorporated electrospun chitosan (CS)/polyvinyl alcohol (PVA) nanofibers for potential neural tissue engineering applications.The morphology, structure, and mechanical properties of the formed electrospun fibrous mats were characterized using scanning electron microscopy (SEM) and mechanical testing, respectively. In vitro cell culture of embryonal carcinoma stem cells (P19) were seeded onto the electrospun scaffolds. The results showed that the incorporation of CNTs and BG nanoparticles did not appreciably affect the morphology of the CS/PVA nanofibers. The maximum tensile strength (7.9 MPa) was observed in the composite sample with 5 %wt bioactive glass nanoparticles. The results suggest that BG and CNT-incorporated CS/PVA nanofibrous scaffolds with small diameters, high porosity, and promoted mechanical properties can potentially provide many possibilities for applications in the fields of neural tissue engineering and regenerative medicine.
S.t. Mohammadi Benehi, S. Manouchehri, M.h. Yousefi,
Volume 35, Issue 3 (Journal of Advanced Materials-Fall 2016)
Abstract
Magnesium-manganese ferrite nanopowders (MgxMn1-xFe2O4, x=0.0 up to 1 with step 0.2) were prepared by coprecipitation method. The as-prepared samples were pressed with hydrolic press to form a pellet and were sintered in 900, 1050 and 1250˚C. Scanning Tunneling Microscope (STM) images showed the particle size of powders about 17 nm. The X-ray patterns confirmed the formation of cubic single phase spinel structure in samples sintered at 1250˚C. Substituting Mg2+ with Mn2+ in these samples, the lattice parameter decreased from 8.49 to 8.35Å and magnetization saturation decreased from 74.7 to 21.2emu/g. Also, coercity (HC ) increased from 5 to 23Oe and Curie temperature (TC ) increased from 269 to 392˚C. Samples with x= 0.2, 0.4, 0.6 sintered at 1250 ˚C, because of their magnetic properties, can be recommended for hyperthermia applications and for phase shifters.
M. Illbeigi, A. R. Fazlali, M. Kazazi, A. H. Mohammadi,
Volume 36, Issue 1 (Journal of Advanced Materials-Spring 2017)
Abstract
In this research, new lithium ion conductor glass-ceramics with NASICON-type structure (Li1+x+yAlxCryGe2-x-y (PO4)3, x+y=0.5) were synthesized using melt-quenching method and converted to glass-ceramics through heat treatment. Influence of addition of different concentrations of aluminum and chromium in LiGe2(PO4)3 glass-ceramic was investigated for ionic conduction improvement. Substitution of Ge4+ ions in NASICON structure by Al3+ and Cr3+ ions induced more Li+ ions in A2 vacant sites to obtain charge balance and also changed the unit cell parameters. These two factors led to ionic conductivity improvement of synthesized glass-ceramics. The glass-ceramics were characterized and the amorth structures were investigated by X-ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Energy-Dispersive X-ray spectroscopy (EDX), Differential Scanning Calorimetry (DSC) and Complex Impedance Spectroscopy (CIS). The highest lithium ion conductivity of 8.82×10-3 S/cm was obtained for x=0.4 and y=0.1 (Li1.5Al0.4Cr0.1Ge1.5(PO4)3) crystallized at 850 oC for 8 h with minimum activation energy of 0.267 eV.
M. Akbari Taemeh, B. Akbari, J. Nourmohammadi,
Volume 37, Issue 3 (Journal of Advanced Materials-Fall 2018)
Abstract
In gradient scaffolds, changes in porosity, pore size or chemical composition occur gradually. Recently, different methods have been applied to create gradient in the scaffolds, but they have some disadvantages such as high cost and control. The main purpose of this research was to fabricate porous gradient scaffolds by a novel, functional, simple, and low-cost method. Two homogenous scaffolds (Homog 1 and Homog 2) and two gradient scaffolds (Grad 1 and Grad 2) were fabricated and compared. Polycaprolactone scaffolds with the pore size gradient along the radial direction were fabricated by combining layer-by-layer assembly and porogen leaching techniques. Paraffin micro particles were used as porogen in two size ranges: 250 to 420 µm and 420 to 600 µm. The average pore size of Homog 1 and Homog 2 was 278.48 ± 11.23 µm and 417.79 ± 14.62, which were suitable for bone tissue engineering. The porosity of the samples was: Homog 1: 77.5 ± 1.25 %, Homog 2: 61.3 ± 3.5 %, Grad 1: 74 ± 0.5 % and Grad 2: 79.8 ± 4 %. It should be stated that the required porosity for cell survival and growth was above 70 %. Compressive strength at 80% strain and compressive modulus for Homog 1, Homog 2, Grad 1 and Grad 2 were 0.16 ± 0.16 MPa and 0.25 ± 0.11 MPa, 0.26 ± 0.20 MPa and 0.53 ± 0.34 MPa, 0.19 ± 0.34 MPa and 0.33 ± 0.43 MPa, 0.12 ± 0.28 MPa and 0.16 ± 0.51 MPa, respectively. The results showed that pore size gradient had a negligible effect on the mechanical properties of the scaffolds and using polycaprolactone (PCL) as the only material of scaffold was not appropriate. The structure of gradient scaffolds showed the radial pore size gradient with a good adhesion between layers without any detectable interface; the result of the compression test also confirmed it.
F. Mohammadi Bodaghabadi, M. R. Loghman Estarki, M. Ramazani, A. Alhaji,
Volume 38, Issue 3 (Journal of Advanced Materials-Fall 2019)
Abstract
In this research, synthesis of lithium fluoride (LiF) nanoparticles by fluorolytic sol-gel method has been studied. Moreover, the effect of lithium ion to fluorine source molar ratio and calcination temperature on particle size and phase of LiF nanoparticles were investigated. Lithium acetate (C2H3LiO2), trifluoroacetic acid (TFA), ethylene glycol monobutyl ether and oleic acid were used as sources of Li+ and F- ions, solvent and growth inhibitor, respectively. Thermal and X-ray diffraction (XRD) analyses as well as field emission scanning electron microscopy (FESEM) were used to investigate thermal behavior of the primary gel and to determine the phase and morphology of samples, respectively. The results showed that the 2: 1 molar ratio of Li+/ TFA and the calcination temperature of 400 °C result in LiF nanoparticles with a mean particle size of 80-100 nm.
R. Karimi-Chaleshtori, M. R. Saeri, A. Doostmohammadi ,
Volume 40, Issue 1 (Journal of Advanced Materials-Spring 2021)
Abstract
Silver nanowires (AgNWs) are considered as one-dimensional nanostructures, which have received much attention due to their nanoscale size, high aspect ratio, high electrical and thermal conductivity, optical transparency and high mechanical stability. Preparation of AgNWs by polyol process is remarkably sensitive to the interactions between synthesis parameters. In this study, the effect of the simultaneous change of four synthetic parameters, namely the reaction temperature, the molecular weight of polyvinylpyrrolidone (PVP) stabilizer, the amount of sodium chloride, as well as, the solution mixing rate by the polyol process was reported. The results of field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM) confirmed that the synthesized AgNWs were below 100 nm. X-ray energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) analysis, as well as, Fourier transform infrared spectroscopy (FT-IR) confirmed that the formed AgNWs were free of impurities. It was also found that temperature, molecular weight of PVP, salt concentration and solution mixing rate caused a significant change in the morphology of AgNWs. More importantly, a strong interaction was created in the preparation process of AgNWs by adjusting the parameters.
S. H. Hashemi Rizi , A. Nourmohammadi Abadchi,
Volume 40, Issue 4 (Journal of Advanced Materials-Winter 2022)
Abstract
Development of materials with the ideal black body absorption spectrum are of great interest. Such materials could improve the efficiency of solar cells, and passive cooling and heat transfer systems as well as the protective and decorative coatings. Fabricating black anodizing coatings is promising for this purpose because they exhibit low light reflection from the surface. Such coatings can be produced through successive anodizing and black coating of aluminum alloys. In this study, the effect of anodizing repetition on the absorption coefficient of the black anodizing coatings on 2024 aluminum alloy was investigated, as model. All the parameters were fixed in the black coloring stage to evaluate the influence of the anodizing steps. After a one-step anodizing, the black coatings showed an absorption coefficient of 0.956 in the visible region and 0.911 in the of 220 to 2200 nm wavelength range, while their absorption coefficient increased after a three-step anodizing up to 0.982 in the visible region and up to 0.966 in the 220 to 2200 nm wavelength range. This indicates that anodizing repetition helps the optical absorption of black anodizing coatings to approach the optical absorption of an ideal black body.
A. Mohammadi, B. Niroumand, A. Saboori,
Volume 40, Issue 4 (Journal of Advanced Materials-Winter 2022)
Abstract
Electron beam melting (EBM) is among the modern additive manufacturing processes whereby metal powders are selectively melted to produce very complicated components with superior mechanical properties. In this study, microstructure, hardness, and surface roughness of EBM fabricated Ti6Al4V samples were characterized. The results showed that the microstructure consisted of epitaxially-grown primary columnar β phase transformed to basketweave and Widmanstatten-type α phase during the subsequent rapid cooling. Martensitic needle-type α phase was also observed on the surfaces of the specimens. It was shown that higher parts of the sample had finer microstructures than the lower parts reaching to less than 340 nm in average thickness of the α layers due to distancing from the hot build platform rendering less opportunity for diffusional β → α+β transformation. The porosity content of the samples was lower than that of some other additive manufacturing processes. Vickers micro-hardness of the samples was measured to be around 337 HV which was higher than those reported for other additive manufacturing processes of the alloy.
Sh. Talebniya, M. R. Saeri, I. Sharifi, A. Doostmohammadi,
Volume 41, Issue 1 (Journal of Advanced Materials-Spring 2022)
Abstract
Magnetic nanoparticles are of interest in various research fields such as magnetic fluids, catalysts, biotechnology, medicine, information storage, and environmental issues. However, spinel ferrite magnetic nanoparticles with proper magnetic properties could not be used alone in these applications because of their lack of biocompatibility and instability in aqueous solutions. Surface coating is an effective strategy to eliminate or minimize this issue. In this study, FeFe2O4 and ZnFe2O4 spinel ferrites were synthesized using the reverse co-precipitation method under a nitrogen gas atmosphere. The magnetic behavior of the particles, determined by a vibrating magnetometer (VSM) showed the saturation magnet (Ms) values of the FeFe2O4 and ZnFe2O4 spinel. Fourier-transform infrared (FTIR) spectra showed two high-frequency bands v1 and v2 at about 554-578 and 368-397 cm-1, respectively, which were related to the spinel structure. Finally, the synthesized FeFe2O4 nanoparticles were coated with chitosan and polyethylene glycol (PEG) biopolymers. The TEM and FTIR analysis indicated that the magnetic nanoparticles were uniformly coated by the biopolymers.
N. Mohammadi, B. Lotfi,
Volume 41, Issue 2 (Journal of Advanced Materials-Summer 2022)
Abstract
The purpose of this study was to improve the erosion behavior of Inconel 625 alloy by plasma transferred arc-deposited stellite6/B4C composite cladding. For this purpose, 5 wt.% of boron carbide was added to the stellite6 clad. Phase analysis and microstructure evaluation were conducted by Optical Microscope, Field Emission Scanning Electron Microscope (FESEM), and Energy-dispersive Spectroscopy (EDS). Solid particle erosion tests with silica particles at 30˚ and 90˚ impact angles were performed to study the erosion behavior. Eroded surfaces were observed by SEM. Investigations showed that the addition of boron carbide particles caused finer microstructure in composite cladding. Moreover, hardness increased with adding boron carbide. Maximum erosion resistance was achieved at 30˚ impact angle. The weight loss of composite cladding were 20 % and 33 % compared to those obtained in Inconel 625 substrate and stellite6 cladding, respectively. The weight loss of the claddings and substrate showed negligible difference at 90˚ impact angle. The dominant mechanism of erosion for composite cladding at 30˚ impact angle was suggested to be cutting and detachment of reinforcing particles. Crater formation was found the predominant mechanism of erosion at 90˚ impact angle.
