Showing 238 results for Gh
M. Rajabi, M. Shahmiri, M. Ghanbari,
Volume 37, Issue 4 (Journal of Advanced Materials-winter 2019)
Abstract
In this study, the effects of boron (B) and zirconium (Zr) on the microstructure and mechanical properties of Fe3Al-based alloys were investigated. Cylindrical samples were produced using a vacuum induction melting furnace (VIM); consequently, the melt was cast into a metallic mold. The microstructure, phase identification, tensile and compressive mechanical properties and fractography of the samples were investigated. Upon microstructural observation, it was found that the alloys microstucture was denderitic and the precipitated phases were mostly present between interdendritic regions. Addition of B and Zr to the alloys resulted in the formation of boride precipitates and Laves phases. The results, therefore, showed that Zr had the most pronounced effect on the mechanical properties because of the formation of Laves phases. Fractographic studies of alloys also revealed that the brittle fracture was dominant between the samples.
M. Hajfarajzadeh, A. Eshaghi, A. Aghaei,
Volume 37, Issue 4 (Journal of Advanced Materials-winter 2019)
Abstract
A TEOS-GPTMS nano-hybrid thin film was deposited on the polymethyl methacrylate (PMMA) substrate by a sol-gel dip coating method. Morphology, roughness and surface chemical bonding of the thin films were evaluated by X-ray diffraction (XRD), field emission scanning electron microscopy(FE-SEM), atomic force microscopy, and Fourier transform infrared spectroscopy methods, respectively. UV-vis spectrophotometer was used to measure the transmittance spectra of the samples. Also, the adhesion and hardness of the coatings were investigated using pencil hardness the adhesion tape test and the test, respectively. XRD results proved that the thin film had an amorphous structure. Also, FE-SEM images indicated that addition of GPTMS to the TEOS yielded a crack-free thin film. Based on the UV-vis spectroscopy results, the transmittance of the polymer substrate in the visible region was increased by the deposition of the nano-hybrid coating. Moreover, the hardness of the PMMA substrate was increased from 3H to 6H by the deposition of the nano-hybrid thin film. Also, tape test confirmed the high adhesion of the nano-hybrid thin film on the PMMA substrate. Consequently, the transparent organic-inorganic GPTMS-TEOS hybrid coating can be used as a scratch resistant coating on the PMMA substrate.
M. Eshraghi, Z. Mosleh, M. Rahimi,
Volume 38, Issue 1 (Journal of Advanced Materials-Spring 2019)
Abstract
In this investigation, the structural and magnetic properties of Cr and Zn substituted Co ferrite with the general formula Co1-xZnxFe2-xCrxO4 (x= 0.1, 0.3, 0.5, 0.7) as prepared by sol- gel method were studied. The structural, morphological and magnetic properties of the samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Scanning electron microscopy (SEM) and Vibrating sample magnetometer (VSM). XRD measurements along with the Rietveld refinement indicated that the prepared samples were single phase with the space group of Fd-3m. Results of SEM images also showed that the particles were in the nanosize range. Also, the magnetic properties of the samples indicated that the magnetization was first decreased, reaching the minimum value for x=0.1 sample; then it was increased. This behavior was related to the cation distribution at the tetrahedral and octahedral sites. Moreover, coercivity was significantly decreased with increasing the doping level due the decrease of magnetocrystalline anisotropy because of the nonmagnetic Zn ion substitution.
M. Samii Zafarghandi, S. M. Abbasi,
Volume 38, Issue 2 (Journal of Advanced Materials-Summer 2019)
Abstract
In the present work, hot tensile behavior of Haynes 25 Co-base alloy was investigated in the temperature range of 950-1200 ˚C and 0.1 s-1. Thermodynamic calculations showed that M23C6 and M6C carbides were stable below 1000 ˚C and above 1050 ˚C, respectively. Stress-strain curves also indicated an unusual trend of strain fracture. It was observed that with increasing temperature from 950 to 1050 ˚C, the fracture strain was decreased, while it was raised above 1050 ˚C again. Increasing the volume fraction of M6C carbide rich in Tungsten resulted in the loss of ductility. Also, microstructural evaluations showed dynamic recrystallization (DRX) grains were nucleated and growth was around carbides and the initial grains at 1150 ˚C. Occurrence of DRX led to the improvement of ductility via grain refinement mechanism, so this alloy had the highest level of ductility at 1150 ˚C
M. Ghasemian Malakshah, F. Ashrafizadeh, A. Eslami, F. Fadaeifard,
Volume 38, Issue 2 (Journal of Advanced Materials-Summer 2019)
Abstract
Since martensitic precipitation hardened 17-4pH stainless steel has been widely used in corrosive environments, evaluation of its corrosion fatigue behavior is important. In this research, after microstructural studies, mechanical, corrosion, fatigue and corrosion fatigue tests were performed on 17-4pH specimens. Fatigue and corrosion fatigue tests were carried out at the stress ratio of -1 and the stress frequency of 0.42 Hz (to increase the effect of corrosive solution), and corrosion fatigue tests were conducted in 3.5% NaCl solution, an environment similar to corrosive sea water. Fatigue limit of 17-4pH stainless steel was 700 MPa in air and 415 MPa in corrosive environment. Comparing the S-N curves of this alloy at the optimal heat treatment cycle in two modes of fatigue and corrosion fatigue revealed the reduction of fatigue limit up to 40 % in the presence of corrosive environment. This reduction was due to the effect of observed corrosion pits on the surface and Damaged passive layer.
M. Maniei, A. Eshaghi, A. Aghaei,
Volume 38, Issue 2 (Journal of Advanced Materials-Summer 2019)
Abstract
In this research, MgF2-2%SiO2/MgF2 thin films were applied on a glass substrate. At first, MgF2 thin films with the optical thickness were deposited on the glass slide substrates. Then, MgF2-2%SiO2 thin films were deposited on the glass coated with MgF2 thin films. Finally, the nanocomposite thin films were surface treated by the PFTS solution. Characterization of the thin film was done by X-Ray defractometry (XRD), attenuated total reflectance fourier transform infrared spectroscopy (ATR-FTIR), UV-Vis spectroscopy, and atomic force microscopy (AFM) techniques. Also, the hydrophobic properties of the samples were investigated by measuring the contact angle of the water. The results showed that the deposition of the six layer MgF2 thin films on the two sides of the glass substrate increased the transmission up to 96.4%. For the glass deposited by MgF2-2%SiO2 nanocomposite thin films, transmission was reduced to 94.4%, with its transmission being higher than the pure glass. Also, the water contact angle (WCA) analysis determined that the contact angle of the water droplet on the MgF2-2%SiO2 nanocomposite thin film coated glass was decreased. On the other hand, the contact angle of the water droplet on the MgF2-2%SiO2 nanocomposite thin film coated glass after modification with the PFTS solution was increased up to 119o. So, MgF2-2%SiO2 nanocomposite thin films could be used as an antireflective and self-cleaning coating on the surface of the optical devices.
N. Alirezaei Varnosfaderani, S. E. Mousavi Ghahfarokhi, M. Zargar Shoushtari,
Volume 38, Issue 3 (Journal of Advanced Materials-Fall 2019)
Abstract
In this paper, W-type SrCo2Fe16O27 hexaferrite nanostructures were synthesized by sol-gel auto-combustion method. Effect of annealing temperature on the structural, magnetic and optical properties of these SrCo2Fe16O27 nanostructures was investigated. In order to determine the annealing temperature of samples, the prepared gel was examined by thermo-gravimetric and differential-thermal analyses. Morphology and crystal structure of the prepared samples were characterized by field emission scanning electron microscopy and X-ray diffraction pattern. Based on X-ray diffraction results, at annealing temperature of 1000 °C, the maximum amount of main phase formed. A planar morphology was spectroscopy for the synthesized samples through scanning electron microscope images. Fourier transform infrared analysis was used to confirm the synthesis of the main properties obtained of samples were measured by the vibrating sample magnetometer and the results showed that by increasing temperature, magnetic saturation increases. Moreover, optical properties of samples were investigated by ultraviolet–visible absorption and photoluminescence spectroscopies. The result of measurements of the energy gap approximately is same in the ultraviolet- visible and photoluminescence spectroscopes and also the energy gap is constant with increasing temperature.
F. Mohammadi Bodaghabadi, M. R. Loghman Estarki, M. Ramazani, A. Alhaji,
Volume 38, Issue 3 (Journal of Advanced Materials-Fall 2019)
Abstract
In this research, synthesis of lithium fluoride (LiF) nanoparticles by fluorolytic sol-gel method has been studied. Moreover, the effect of lithium ion to fluorine source molar ratio and calcination temperature on particle size and phase of LiF nanoparticles were investigated. Lithium acetate (C2H3LiO2), trifluoroacetic acid (TFA), ethylene glycol monobutyl ether and oleic acid were used as sources of Li+ and F- ions, solvent and growth inhibitor, respectively. Thermal and X-ray diffraction (XRD) analyses as well as field emission scanning electron microscopy (FESEM) were used to investigate thermal behavior of the primary gel and to determine the phase and morphology of samples, respectively. The results showed that the 2: 1 molar ratio of Li+/ TFA and the calcination temperature of 400 °C result in LiF nanoparticles with a mean particle size of 80-100 nm.
N. Safari, M. Toroghinejad, M. Kharaziha, V. Saeedi,
Volume 38, Issue 3 (Journal of Advanced Materials-Fall 2019)
Abstract
The aim of this study was to fabricate the Mg-1Al-Cu alloys with various amounts of Cu content (0, 0.25, 0.5 and 1 wt.%) using spark plasma sintering (SPS) approach and evaluation of their degradation rate and biological properties. The results indicated that Cu incorporation (0.25 wt.%) significantly diminish degradation rate from 0.039 cm/h in pure Mg to 0.00584 cm/h in Mg-1Al-0.25Cu alloy. In addition, Mg-1Al-0.25Cu alloy could noticeably (1.25 times) promote viability of MG63 cells compared to pure Mg, owing to the optimized ion release. Moreover, the antibacterial activity of Mg-1Al-0.25Cu was considerable. In summary, Mg-1Al-0.25Cu alloy with appropriate degradation rate, good biocompatibility and antibacterial properties can be introduced as a biodegradable orthopedic implant.
G. R. Faghani, A. R. Khajeh-Amiri,
Volume 38, Issue 4 (Journal of Advanced Materials-Winter 2020)
Abstract
Due to special properties such as low density, high strength and high corrosion resistance Ti-6Al-4V alloy has been used extensively in various industries, especially in the aerospace aspects. However the major problem of this alloy is its poor tribological properties under relatively high loads. In the present study, in order to improve the tribological properties of mentioned alloy, chromium particles were added to Ti-6Al-4V layers in the nitrogen-containing atmosphere during the Tungsten Inert Gas (TIG) welding process. Microstructural investigations using optical microscopy, X-ray diffraction analysis and scanning electron microscopy, proved the formation of TiN, TiCr2 and Cr2N particles in the matrix of hard titanium phase. The hardness of TIG alloyed layer increased to 1000 HV0.3 which was 4 times higher than that of the base alloy. Moreover, the wear rate of TIG alloyed samples with chromium and nitrogen under 30N load and distance of 1000 m was 5.9 times lower than that of the bare Ti-6Al-4V alloy.
M. R. Loghman Estarki, H. Ghalibaf Tousi, E. Mohammad Sharifi, H. Sheikh, A. Alhaji,
Volume 38, Issue 4 (Journal of Advanced Materials-Winter 2020)
Abstract
The purpose of this study was to evaluate the effect of glycyrol (tri-dentate, GLY) and ethylenediamine (double- dentate clay, en) chelating agents on phase and morphology changes of spinel nanoparticles synthesized by sol-gel method. Characterization of samples was performed by X-ray diffraction (XRD) and field-emission scanning electron microscope (FESEM) equipped with energy dispersive X-ray spectrometer (EDX). The results showed that both samples synthesized with GLY and en contain cubic spinel phase. The sample synthesized with ethylenediamine has a pyramidal morphology with particle size in the range of 20-25 nm whereas the specimen prepared with glycerol is spherical with particle size in the range of 20-25 nm. Finally, suggested mechanism for morphological changes of spniel nanoparticles was discussed.
A. Faeghinia, H. Mardi,
Volume 38, Issue 4 (Journal of Advanced Materials-Winter 2020)
Abstract
Amorphous steel slag was blended with different concentrations of waste glass (20, 40, 50, 60, 70 wt.%) and SiC to obtain a composite. According to Hot Stage Microscopy images, slag-glass composite contractions started at 1050 ºC. scanning electron microscope micrographs of slag-SiC (foaming agent) composite revealed tunnel-like porosities of 500 to 1000 microns. Gaseous products of carbide decomposition led to the formation of these tunnel-like porosities. By adding up to 50 wt. % of waste glass to this composite and sintering at 1200 ° C, the size of cavities decreased by 10 times and achieved 50 microns to form spherical cavities. By increasing glass content, the total porosity of slag-glass-SiC increased to 80 wt.% followed by a decrease in the strength to 3.2 MPa. Having an overall density of 0.8 g/cm3, the slag-glass composite could be classified as a porous foam material. Pseudo Waltonite phase was also detected in this composite after sintering.
F. Shahriari Nogorani, M. Afari, M. A. Taghipoor, A. Atefi,
Volume 39, Issue 1 (Journal of Advanced Materials-Spring 2020)
Abstract
Practical applications of thermal barrier coatings with aluminide bond-coats are limited due to oxide scale spallation of the aluminide coating under applied thermal stresses. Considering the positive effects of oxygen-active elements or their oxides on the high temperature oxidation behavior, in this research zirconia was introduced into an aluminide coating. For this purpose, a Watts type bath was used to electroplate a layer of Ni-ZrO2 composite on a Ni-based substrate. Aluminizing was performed using the conventional two-step process at 760 and 1080 °C. Microstructural characterization of coatings in the as-coated conditions and after cyclic oxidation via 5-hour cycles at 1050 °C was performed using electron microscopy, energy dispersive spectroscopy and X-ray diffractometry. The results showed that the general three-zone microstructure of the simple high activity aluminide coatings develops below the pre-deposited nickel-zirconia layer and latter converts to a nearly un-alloyed porous NiAl. In spite of its porous surface layer, the zirconia modified coating has a higher oxidation resistance than the unmodified aluminide coating.
A. Ghasemi, M. R. Loghman Estarki, S. Torkian, G. R. Gordani,
Volume 39, Issue 2 (Journal of Advanced Materials-Summer 2020)
Abstract
The purpose of this study was to evaluate phase changes and magnetic properties of neodymium doped Ni0.7Zn0.3NdxFe2-xO4 (x = 0, 0.01, 0.03, 0.05, 0.07, 0.10) nanoparticles synthesized by complexing sol-gel method. In this method, triethanolamine (TEA) acted as both a gelling agent and a chelating agent. Samples were characterized by X-ray diffraction (XRD) analysis, field emission scanning electron microscopy (FESEM), and energy dispersive X-ray spectroscopy (EDX). XRD patterns of all synthesized samples revealed the formation of a spinel ferrite phase. Magnetic evaluation of the specimens showed that the Nd0.01 doped sample with a quasi-spherical morphology and particle size of about 60 nm has the highest saturation magnetization of 50 emu/g and coercive force of 103 Oe.
S. Asghari, A. M. Eslami, A. Taheri Zadeh, N. Saeidi,
Volume 39, Issue 3 (Journal of Advanced Materials-Fall 2020)
Abstract
In this study, the effect of welding heat input on microstructure and mechanical properties of dissimilar joints of API-X42 and API-B pipeline steels was investigated. Evaluation of the microstructures showed that increasing the welding heat input decreased acicular ferrite in weld metal microstructure, while amount of Widmanstatten ferrite, polygonal ferrite and grain boundary ferrite increased. Also, results of microhardness test showed that by increasing the heat input, hardness of weld metal and the heat affected zone decreased. Tensile test results showed that as the heat input increased, fracture transferred from base metal of API-B to the heat affected zone. Impact test results also showed that increasing the welding heat input could sharply drop the impact energy of the heat affected zone for both base metals due to extensive grain growth.
A. Zamani, M. R. Loghman Estraki, S. R. Hosseini, M. Ramezani, A. Al-Haji,
Volume 39, Issue 3 (Journal of Advanced Materials-Fall 2020)
Abstract
The aim of the study was to investigate the effect of temperature, time, pH, capping agent concentration (mercaptoacetic acid), Zn to Se and Se to reducing agent (NaBH4) mole ratios on morphology, phase developments and size of zinc selenide nanoparticles prepared by hydrothermal method. Characterization of zinc selenide nanoparticles was performed by Field Emission Electron Microscopy (FESEM), Energy Dispersive X-ray Spectrometry (EDS), X-ray Diffraction (XRD), Induced Coupled Plasma Spectrometry (ICP), Fourier Transform Infrared spectroscopy (FTIR) and Simultaneous Thermal Analysis (STA). The results of EDS showed that the ratio of atomic percentage of Zn to Se in the optimized zinc selenide nanoparticles is 1: 1 and elements are evenly distributed in the nanoparticles. Based on the results of FTIR and STA thermal analyses, MAA as the stabilizing agent binds to and stabilizes zinc selenide nanoparticles. Finally, fine nanoparticles of zinc selenide with narrow size distribution, spherical shape and cubic crystal structure were obtained at the minimum temperature (130 °C) and processing time (15 hours) with the least amount of reducing and capping agents compared to previous researches.
I. Forooghi , M. Mashhadi,
Volume 39, Issue 4 (Journal of Advanced Materials-Winter 2021)
Abstract
Due to their unique features, Ultra-High Temperature Ceramics (UHTCs) have potential applications in aerospace, military and industry. ZrB2-SiC composite as one of these ceramics has been at the center of researches due to its attractive mechanical, thermal and oxidation resistance. In this study, the effect of ZrC addition on pressureless sintering behavior, mechanical, microstructural and thermal properties of ZrB2-SiC nanocomposite were investigated. For this purpose, micron-sized ZrB2 and ZrC powders and nano-sized SiC powder were used. ZrB2-20vol% SiC nanocomposites with addition of (3, 6, 9, 12, 15) vol% ZrC were sintered by pressureless sintering method at 2100 ºC. The results showed that the addition of ZrC improved relative density, hardness and fracture toughness of ZrB2-20vol% SiC nanocomposite. Optimum properties were obtained in a sample containing 12 vol% ZrC and the relative density, hardness and fracture toughness of this sample were reported to be 99.01%, 16.95 Gpa and 5.43 Mpa.m0.5, respectively. Thermal analysis of the samples showed that by adding ZrC, thermal diffusivity of this nanocomposite reduced. The highest thermal diffusivity at room temperature equaled 35.3 mm2 /s and was obtained for ZS composite.
Kh. Zamani, M. Tavoosi, A. Ghasemi ,
Volume 39, Issue 4 (Journal of Advanced Materials-Winter 2021)
Abstract
In this research, effect of B and Si addition on the structural and magnetic properties of AlCoCrMnNi high-entropy alloys was investigated. The structural and magnetic properties of AlCoCrMnNiX(X= B, Si) alloys were studied by X-ray diffractometer (XRD), scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and vibrating sample magnetometer (VSM). First, the constituent components of the AlCoCrMnNiX (X=B, Si) alloys were mixed for 10 hours. XRD analysis revealed that the solid solution was not formed by mixing. The alloys were then annealed at 900 ˚C for 10 hours. XRD results revealed formation of a solid solution with BCC structure in AlCoCrMnNi and AlCoCrMnNiB alloys. For AlCoCrMnNiSi and AlCoCrMnNiSiB alloys, Ni2Si and Cr2Si3 intermetallics were formed in addition to the solid solution with BCC structure. VSM results suggested that while forming the solid solution for AlCoCrMnNi alloy, soft magnetic properties improved so that magnetic saturation and coercivity increased from 40.22 to 64.46 emu/g, and from 180.143 to 14.09 Oe, respectively.
M. Judaki, M. Seifollahi, S. M. Abbasi, S. M. Ghazi Mir Saeed,
Volume 40, Issue 1 (Journal of Advanced Materials-Spring 2021)
Abstract
In this article, the effects of Pr and Nd were investigated on the microstructure and absorption/desorption characteristics of MmNi5 hydrogen storage alloy. The alloys were prepared in Vacuum induction furnace and the microstructures and phases were analyzed using scanning electron microscopy (SEM) equipped with energy dispersive X-ray analysis (EDS) and X-ray diffraction (XRD). Hydrogen absorption/desorption characteristics was performed on Sievert apparatus. The results showed that the microstructure of the alloys consist of matrix, second phase as a result of Al segregation, porosities and cracks. The amount of second phases and Al in this phase in Mm(Pr,Nd)Ni4.7Al0.3 is less than MmNi4.7Al0.3. Al in Mm(Pr,Nd)Ni4.7Al0.3 were more homogenized. Pressure-Composition Isotherms of hydrogen absorption/desorption at 25˚C showed that for MmNi4.7Al0.3 and Mm(Nd,Pr)Ni4.7Al0.3, absorption pressures were 14.52 and 9.90 bar, desorption pressures were 5.53 and 5.49 bar, hydrogen storage capacities were 1.37 and 1.33 wt. % and hysteresis were 0.73 and 0.58, respectively. These results are useful in industrial applications, because of inconsiderable decrease in hydrogen storage capacity and the other positive variation in absorption/desorption characteristics, especially the hysteresis and absorption pressure.
H. R. Karimi, H. Mansouri, M. R. Loghman Estarki, M. Tavoosi , H. Jamali,
Volume 40, Issue 1 (Journal of Advanced Materials-Spring 2021)
Abstract
This study aimed to compare the phase changes and morphology of yttria-stabilized zirconium oxide powders (YSZ) synthesized by co-precipitation and molten salt methods. Ammonia precipitating agent was used for the synthesis of YSZ powder by co-precipitation method and a mixture of sodium carbonate and potassium carbonate salts was used as a molten salt in the molten salt method. Samples were characterized by X-Ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Fourier Transform Infrared Spectroscopy (FTIR), Thermal Gravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC) analysis. The results showed that only the sample prepared with zirconium oxychloride and yttrium nitrate by co-precipitation method had a single phase of yttria-stabilized zirconium oxide with tetragonal crystal lattice and particle size distribution in the range of 30 to 55 nm. The powder synthesized by the molten salt method contained a mixture of zirconia with monoclinic crystal lattice and yttria stabilized zirconia with tetragonal crystal lattice and particle size of 200 nm.
