Showing 58 results for Pert
A. Panahi Moghadam, M. Seifollahi, S. M. Abbasi, S. M. Ghazi Mirsaeed,
Volume 37, Issue 2 (9-2018)
Abstract
This paper was concerned with the effect of Mg on the temperature mechanical behavior and evaluation of the microstructure. The results showed that with increasing Mg from 0 to 47 ppm, the grain size was reduced from 64 to 38 µm and the carbides volume fraction was raised from 2.2 to 4.6 vot%. Mg changed the morphology of the carbide from a coarse and continuous one to a separate one. Mg with the mechanisms of grain boundary and matrix/carbide boundary led to changing the carbide composition and also, the mechanical properties. Mg increment from 0 to 47 ppm caused the enhancement of yield strength and rupture life from 309 to 345 MPa and from 16h to 30h, respectively. Grain size and the amount of carbide were the main factors contributing to the rupture of life properties in this study. The increment of the carbide volume fraction was the main mechanism of rupture life enhancement.
M. Lashani Zand, B. Niroumand, A. Maleki,
Volume 37, Issue 4 (3-2019)
Abstract
Mechanical properties of the alloys are a strong function of the average silicon particles size and the secondary dendrite arm spacing (SDAS). Modified Hall-Petch equation expresses the effects of these two microstructural parameters on the yield strength and ultimate tensile strength of the Al-Si based alloys. These microstructural parameters depen on parameters such as chemical composition, cooling rate and melt treatment. In this study, the effect of cooling rate on the equation constants of the alloy were determined. For this purpose, the alloy was poured at 750 °C in three different molds including a sand mold, a preheated steel mold, and a water cooled steel mold. The Thermal and microstructural analysis showed that the cooling rate in the metal mold was 15.7 times higher than that of the sand mold, which resulted in a decrease of the SDAS from 54 micrometers to 17 micrometers. It was also found that by reducing the SDAS from 45 micrometers to 17 micrometers, the yield strength and tensile strength were increased by 16.5% and 6.5%, respectively. The modified Hall-Petch equation constants and the microstructure-mechanical properties relationships were then established by the microstructural and tensile test studies.
M. Rajabi, M. Shahmiri, M. Ghanbari,
Volume 37, Issue 4 (3-2019)
Abstract
In this study, the effects of boron (B) and zirconium (Zr) on the microstructure and mechanical properties of Fe3Al-based alloys were investigated. Cylindrical samples were produced using a vacuum induction melting furnace (VIM); consequently, the melt was cast into a metallic mold. The microstructure, phase identification, tensile and compressive mechanical properties and fractography of the samples were investigated. Upon microstructural observation, it was found that the alloys microstucture was denderitic and the precipitated phases were mostly present between interdendritic regions. Addition of B and Zr to the alloys resulted in the formation of boride precipitates and Laves phases. The results, therefore, showed that Zr had the most pronounced effect on the mechanical properties because of the formation of Laves phases. Fractographic studies of alloys also revealed that the brittle fracture was dominant between the samples.
M. Hajfarajzadeh, A. Eshaghi, A. Aghaei,
Volume 37, Issue 4 (3-2019)
Abstract
A TEOS-GPTMS nano-hybrid thin film was deposited on the polymethyl methacrylate (PMMA) substrate by a sol-gel dip coating method. Morphology, roughness and surface chemical bonding of the thin films were evaluated by X-ray diffraction (XRD), field emission scanning electron microscopy(FE-SEM), atomic force microscopy, and Fourier transform infrared spectroscopy methods, respectively. UV-vis spectrophotometer was used to measure the transmittance spectra of the samples. Also, the adhesion and hardness of the coatings were investigated using pencil hardness the adhesion tape test and the test, respectively. XRD results proved that the thin film had an amorphous structure. Also, FE-SEM images indicated that addition of GPTMS to the TEOS yielded a crack-free thin film. Based on the UV-vis spectroscopy results, the transmittance of the polymer substrate in the visible region was increased by the deposition of the nano-hybrid coating. Moreover, the hardness of the PMMA substrate was increased from 3H to 6H by the deposition of the nano-hybrid thin film. Also, tape test confirmed the high adhesion of the nano-hybrid thin film on the PMMA substrate. Consequently, the transparent organic-inorganic GPTMS-TEOS hybrid coating can be used as a scratch resistant coating on the PMMA substrate.
M. Eshraghi, Z. Mosleh, M. Rahimi,
Volume 38, Issue 1 (6-2019)
Abstract
In this investigation, the structural and magnetic properties of Cr and Zn substituted Co ferrite with the general formula Co1-xZnxFe2-xCrxO4 (x= 0.1, 0.3, 0.5, 0.7) as prepared by sol- gel method were studied. The structural, morphological and magnetic properties of the samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Scanning electron microscopy (SEM) and Vibrating sample magnetometer (VSM). XRD measurements along with the Rietveld refinement indicated that the prepared samples were single phase with the space group of Fd-3m. Results of SEM images also showed that the particles were in the nanosize range. Also, the magnetic properties of the samples indicated that the magnetization was first decreased, reaching the minimum value for x=0.1 sample; then it was increased. This behavior was related to the cation distribution at the tetrahedral and octahedral sites. Moreover, coercivity was significantly decreased with increasing the doping level due the decrease of magnetocrystalline anisotropy because of the nonmagnetic Zn ion substitution.
H. R. Shahverdi, R. Alipour Mogadam,
Volume 38, Issue 2 (9-2019)
Abstract
Creep age forming (CAF) process is a novel metal forming method with major benefits including improved mechanical properties and cost reduction for aviation industry applications. CAF happens due to creep phenomenon and stress-release during the artificial aging of heat-treatable aluminum alloys. In this work, the creep age forming of 7075 Aluminum alloy at 120, 150 and 180 °C for 6, 24 and 48 h was done; tensile and hardness tests were used to characterize the samples. Results on spring-back revealed that it was influenced by time and temperature; by increasing the time and temperature, it was reduced from 54.1 to 39.51. Mechanical property evaluation also showed that by increasing the time, the strength and hardness could be enhanced due to microstructural evolution and precipitation during the CAF process. According to the mechanical and CAF results, two samples were selected as the optimum ones and their work hardening behavior and fracture surfaces were investigated
M. Maniei, A. Eshaghi, A. Aghaei,
Volume 38, Issue 2 (9-2019)
Abstract
In this research, MgF2-2%SiO2/MgF2 thin films were applied on a glass substrate. At first, MgF2 thin films with the optical thickness were deposited on the glass slide substrates. Then, MgF2-2%SiO2 thin films were deposited on the glass coated with MgF2 thin films. Finally, the nanocomposite thin films were surface treated by the PFTS solution. Characterization of the thin film was done by X-Ray defractometry (XRD), attenuated total reflectance fourier transform infrared spectroscopy (ATR-FTIR), UV-Vis spectroscopy, and atomic force microscopy (AFM) techniques. Also, the hydrophobic properties of the samples were investigated by measuring the contact angle of the water. The results showed that the deposition of the six layer MgF2 thin films on the two sides of the glass substrate increased the transmission up to 96.4%. For the glass deposited by MgF2-2%SiO2 nanocomposite thin films, transmission was reduced to 94.4%, with its transmission being higher than the pure glass. Also, the water contact angle (WCA) analysis determined that the contact angle of the water droplet on the MgF2-2%SiO2 nanocomposite thin film coated glass was decreased. On the other hand, the contact angle of the water droplet on the MgF2-2%SiO2 nanocomposite thin film coated glass after modification with the PFTS solution was increased up to 119o. So, MgF2-2%SiO2 nanocomposite thin films could be used as an antireflective and self-cleaning coating on the surface of the optical devices.
N. Alirezaei Varnosfaderani, S. E. Mousavi Ghahfarokhi, M. Zargar Shoushtari,
Volume 38, Issue 3 (12-2019)
Abstract
In this paper, W-type SrCo2Fe16O27 hexaferrite nanostructures were synthesized by sol-gel auto-combustion method. Effect of annealing temperature on the structural, magnetic and optical properties of these SrCo2Fe16O27 nanostructures was investigated. In order to determine the annealing temperature of samples, the prepared gel was examined by thermo-gravimetric and differential-thermal analyses. Morphology and crystal structure of the prepared samples were characterized by field emission scanning electron microscopy and X-ray diffraction pattern. Based on X-ray diffraction results, at annealing temperature of 1000 °C, the maximum amount of main phase formed. A planar morphology was spectroscopy for the synthesized samples through scanning electron microscope images. Fourier transform infrared analysis was used to confirm the synthesis of the main properties obtained of samples were measured by the vibrating sample magnetometer and the results showed that by increasing temperature, magnetic saturation increases. Moreover, optical properties of samples were investigated by ultraviolet–visible absorption and photoluminescence spectroscopies. The result of measurements of the energy gap approximately is same in the ultraviolet- visible and photoluminescence spectroscopes and also the energy gap is constant with increasing temperature.
N. Safari, M. Toroghinejad, M. Kharaziha, V. Saeedi,
Volume 38, Issue 3 (12-2019)
Abstract
The aim of this study was to fabricate the Mg-1Al-Cu alloys with various amounts of Cu content (0, 0.25, 0.5 and 1 wt.%) using spark plasma sintering (SPS) approach and evaluation of their degradation rate and biological properties. The results indicated that Cu incorporation (0.25 wt.%) significantly diminish degradation rate from 0.039 cm/h in pure Mg to 0.00584 cm/h in Mg-1Al-0.25Cu alloy. In addition, Mg-1Al-0.25Cu alloy could noticeably (1.25 times) promote viability of MG63 cells compared to pure Mg, owing to the optimized ion release. Moreover, the antibacterial activity of Mg-1Al-0.25Cu was considerable. In summary, Mg-1Al-0.25Cu alloy with appropriate degradation rate, good biocompatibility and antibacterial properties can be introduced as a biodegradable orthopedic implant.
H. Salehi, N. Zhulayi Bakhoda, P. Amiri,
Volume 38, Issue 4 (1-2020)
Abstract
In this research, the optical properties of tungsten disulfide including dielectric function, the static refractive index, the imaginary part of the dielectric function, optical band gap, energy loss spectrum and its magnetic properties have been studied. Calculations have been done by using Quantum Espresso package which is based on density functional theory and pseudo-potential technique. The static refractive indices of this compound at diffrent x and z directions were calculated 3.66 and 2.55, respectively. The amount of optical band gap, obtained from the imaginary part of dielectric function, was estimated to be 1.45 eV. In addition, bulk plasmon energy, obtained from energy loss spectrum at x and z directions, were obtained to be 17.95 eV and 17.25 eV, respectively.
S. Torabi, S. Khorshidi, A. Karkhaneh,
Volume 39, Issue 2 (8-2020)
Abstract
For many years, dexamethasone has been used as an anti-inflammatory drug and is still one of the safest glucocorticoids for treating various diseases. Due to the wide range of the side effects of this drug, it is essential to find a suitable delivering system for reduction in dosage with increased effectiveness. Electrospinning is one of the fiber fabrication methods which is widely used to develop drug carriers due to its ability to load various drugs and biological components and control their release. In this research, neat poly (lactic acid) electrospun fibers and dexamethasone loaded fibers were prepared. To evaluate the effect of polymer concentration on morphology, mechanical properties and drug release profile of the resulting fibers, three polymer concentrations of 10%, 14% and 18% w/v were processed. Thereafter, 5% w/v dexamethasone was added to solutions. The scanning electron microscopy images were investigated to obtain the average diameter of fibers and the average area of pores in each sample. In neat samples, by moving from 10% to 18% composition, the average diameter of the fibers increased by 63.21%. However, in drug loaded samples this increased by 51/19%. After evaluating mechanical properties, an increase of 81/34% in Elastic modulus by moving from 10% to 18% composition was observed. Moreover, the ultimate strength increased by 68/021% when increasing the polymer concentration from 10 to 18%. Drug release from the electrospun samples was continued up to 7 days. Linear release was observed in 10% and 14% compositions. The drug release pattern of these samples was of zero order. Considering the importance of zero order release in different applications of dexamethasone, these delivering systems could be useful. The maximum drug release rate belonged to 14% composition (0.044 1/h).
A. Zolriasatein, S. Navazani, M. Rezaei Abdadchi, N. Riahi Noori ,
Volume 39, Issue 3 (12-2020)
Abstract
In this paper, the effect of adding aluminum trihydrate (ATH) on electrical (including dielectric constant, dielectric loss and strength, volume and surface resistivity) and hydrophobic properties of two-part room temperature volcanized (RTV) silicone rubber resin coatings were investigated. For this purpose, the RTV-ATH nanocomposite was made by physical mixing and its electrical and hydrophobic properties were compared with those of pure RTV. The results showed an increase in the dielectric constant (from 3.11 to 4.13), the dielectric loss (by ~ 0.06) and the dielectric strength (by ~ 4 KV/mm) of the RTV-ATH composite compared to the pure RTV. Moreover, ATH increased volume resistivity and reduced the surface resistivity of composite coatings. On the other hand, by spraying of coatings, no improvement in the hydrophobicity class of composite coating compared to pure RTV was observed and both samples were standardized in the HC2 standard class. Structural analysis of samples was performed by X-ray diffraction, optical microscopy and scanning electron microscopy and the presence of the main phases in them was confirmed.
S. Asghari, A. M. Eslami, A. Taheri Zadeh, N. Saeidi,
Volume 39, Issue 3 (12-2020)
Abstract
In this study, the effect of welding heat input on microstructure and mechanical properties of dissimilar joints of API-X42 and API-B pipeline steels was investigated. Evaluation of the microstructures showed that increasing the welding heat input decreased acicular ferrite in weld metal microstructure, while amount of Widmanstatten ferrite, polygonal ferrite and grain boundary ferrite increased. Also, results of microhardness test showed that by increasing the heat input, hardness of weld metal and the heat affected zone decreased. Tensile test results showed that as the heat input increased, fracture transferred from base metal of API-B to the heat affected zone. Impact test results also showed that increasing the welding heat input could sharply drop the impact energy of the heat affected zone for both base metals due to extensive grain growth.
A. Borouni, A. Kermanpur,
Volume 39, Issue 3 (12-2020)
Abstract
In this study, the effect of Ta/W ratio on the microstructure and stress rupture properties of Ni-based single crystal (SX) superalloy PWA1483 was investigated. For this purpose, single crystal (SX) superalloys with different Ta/W ratios (0.75, 1.0, 1.32 and 1.5 in wt.%) were fabricated. The alloys were directionally solidified by Bridgman method under the same solidification condition at withdrawal velocity of 3 mm/min and thermal gradient of about 7 K/mm followed by standard age hardening heat treatment. Microstructural characterization was performed using optical microscopy (OM) and scanning electron microscopy (SEM). The stress rupture properties were investigated at 982 °C and 248 MPa. The results showed that increasing the Ta/W ratio decreases the size and volume fraction of micro-pores together with the size of γ' precipitates. Hence, the stress rupture life increased. The superalloy with Ta/W ratio of 1.5 showed the minimum size of micro-porosity (18.2 μm) and the maximum stress rupture life (~34 h). The superalloy with Ta/W ratio of 1 showed the most uniform microstructure and creep behavior. It seems that the presence of topologically closed packed (TCP) η-phases is the main reason for stress rupture life decrease in SX superalloy as micro-pores initiated from TCP phases or the TCP/matrix interfaces.
M. Shayestefar, A. R. Mashreghi, S. Hasani ,
Volume 40, Issue 1 (5-2021)
Abstract
Mn0.8Zn0.2Fe2-xDyxO4 (where x= 0, 0.025, 0.05, 0.075, 0.1) ferrite nanoparticles were synthesized by auto- combustion sol-gel method for the first time in this study. The effect of Dy-doping on the structural and magnetic properties of the produced specimens was examined using the X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), vibrating sample magnetometery (VSM), and field emission scanning electron microscope (FE-SEM). The results showed that a cubic spinel structure was formed in all of the synthesized specimens. It was also found that the addition of Dy increased the lattice parameter while decreased the average of crystallites size. Furthermore, the FE-SEM micrographs showed that Dy not only plays an effective role in reducing the agglomeration of nanoparticles and their distribution, but also reduces the average of particle size. It was also observed that the addition of Dy had no effect on the morphology of the synthesized nanoparticles. Investigation of the magnetic properties revealed a clear decrease in the saturation magnetization and coercivity by the Dy addition. So that the saturation magnetization of the samples decreased from 66.3 to 58.4 emu/g and the coercivity decreased from 78.5 to 71.9 Oe.
M. Ghorbani, H. Khorsand,
Volume 40, Issue 2 (9-2021)
Abstract
Strontium hexaferrite M-type nanoparticles doped with La and Cu (SrFe12-xCuxO19-Sr1-xLaxFe12-xCuxO19) with different mole fractions (x=0.1-0.2-0.3-0.4-0.5) synthesized by self-combustion sol-gel technique. Firstly, a gel of metal nitrates with the above-mentioned mole fractions were fabricated and the obtained powder was cured at 950°C. Microstructural properties and the morphology of the compounds were investigated by employing X-ray diffraction (XRD) and scanning electron microscopy (SEM). Also, in order to investigate the magnetic properties, Vibrating Sample Magnetometer (VSM) was used. SEM images revealed that the particles had an average size of about 100 nm. Cu2+ ions were substituted with Fe3+ ions within the crystalline sites of SrFe12O19 structure. It was shown that the lattice parameter (a) remained approximately unchanged with an increase in Cu-dopped while the lattice parameter (c) decreased with increasing the mole fraction (x). By using VSM hysteresis diagrams, it was observed that the saturated magnetization and coercive force increased with the addition of La; this was attributed to the variation in the distribution of ions and the shape anisotropy of the nanoparticles. These significant changes in the magnetic properties were for the sample with the composition of Sr1-xLaxFe12-xCuxO19 and SrFe12-xCuxO19, for the x=0.1 and x=0.5, respectively.
H. Saki, M. Morakabati, R. Mahdavi,
Volume 40, Issue 3 (11-2021)
Abstract
Metastable beta titanium alloys have the ability to achieve different microstructures as a result of various heat treatment cycles. The aim of the present study was to create a combination of fine spherical and needle-shaped alpha phase in a metastable beta Titanium alloy (Ti-3Al-8Mo-7V-3Cr) using two-phase solution annealing and aging to improve tensile properties. In this regard, one strip of the alloy was solution annealed in the two-phase region (α+β) at 750°C. Then, some of the solution treated specimens were aged in one step and the others in two steps. The microstructural observation and phase analysis were studied by scanning electron microscope (SEM) and X-ray diffraction (XRD), respectively followed by investigating tensile properties using tensile test. The results exhibited that the microstructure of the alloy after annealing in the two-phase region (α+β) consisted of a spherical primary alpha phase of 1 μm in the beta matrix. One-step aging at 600°C resulted in a microstructure without secondary alpha layers. This heat treatment cycle resulted a yield strength of 980 MPa and fracture strain of 13.9%. Two-step aging at 300°C and 600°C led to formation of the secondary alpha layers with 0.1 μm thickness and increased the yield strength and fracture strain to 1007 MPa and 15.8%, respectively.
F. Rafati, N. Johari, F. Zohari,
Volume 40, Issue 4 (3-2022)
Abstract
In the present study, PCL/ZnO nanocomposite scaffolds containing 0, 5, and 15 wt.% of ZnO nanoparticles were prepared via the salt leaching/solvent casting method. The influence of ZnO nanoparticles on the morphology of prepared PCL/ZnO scaffolds was investigated using SEM images. The compressive strength test evaluated the effect of scaffolds’ morphology on mechanical properties. The XRD technique confirmed the desired phases in the scaffold composition. The results showed that the compressive strength and structural integrity of the scaffolds increased by increasing ZnO nanoparticles content as the reinforcement. However, the compressive strength and structural integrity decreased by increasing the amount of ZnO nanoparticles up to more than 5 wt.%. In summary, PCL/ZnO nanocomposite scaffold containing 5 wt.% of ZnO nanoparticles revealed the highest strength, compressive modulus, and structural integrity.
