Journal of Advanced Materials in Engineering (Esteghlal)

---

In this paper, mixed forced and natural convection heat transfer in a rectangular cavity has been numerically studied. the cavity receives a uniform heat flux from one side and is ventilated with a uniform external flow. The external flow enters the cavity from the heated side and leaves the cavity from the opposite side. The velocity and temperature fields and heat transfer rate are determined by solving the two-dimensional continuity, momentum and energy equations. In this research, steady-state flow with constant Reynolds number, Re=100, is considered. Rayleigh number is in the range of 0≤Ra≤107. First, the results are presented for a cavity with constant aspect ratio, AR=2, and four different inlet and exit opening positions. Then cases with a fixed opening position and different aspect ratios including 0.1, 0.25, 1, 4 and 10 are modeled. In the cavities with opening in the bottom or cavities with aspect ratios less than one, the results show weak effects of natural convection on heat transfer. This research has been done for air as a working fluid (Pr=0.71). In some cases, the results are compared with those from previous studies. Keywords: Convection, Natural, Forced, Cavity, Rayleigh, Ventilate

---

In order to carry out experimental investigations on radial inflow gas turbine, a special test laboratory was designed and constructed at Sharif University of Technology. This laboratory is introduced in the present paper and experimental procedures are elaborated on. Then, some test results are presented and discussed. The trends of performance characterisitics match our expectation and show good agreement with the published research results in this field. Keywords: Radial inflow gas turbine, Experimental, Laboratory, Performance characteristics

---

In this paper, the equation of motion of an elastic 2 DoF wing model has been derived using Lagrange's method. The aerodynamic loads on the wing were calculated via the Strip-Theory and the effect of compressibility was included. Wing deflections due to bending and twist motions were determined using the Assume-Mode method. The aeroelastic equations were solved numerically using the V-g method. The results obtained for different types of wings were in good agreement with experimental data.

---

---

The particles of ferrite Ni0.6-xCuxZn0.4Fe2O4, (0-0.5 in step with 0.1) were prepared by the sol-gel method. Sintering process of powders was carried out at 600, 800 and 1000 oC. The effect of the sintering temperature and chemical composition on the structural and magnetic properties of the Cu substituted NiZn ferrite was investigated. EDS analysis and X-ray diffraction patterns confirmed a well defined of single crystal phase with spinel structure. The thermal behavior process and particle size of samples were investigated by thermal analysis TG, DTA techniques and scanning electron microscope, respectively. VSM curves reveal that the sintering temperature and copper content affect saturation magnetization. M ssbauer spectra displays that the copper cations occupy the octahedral sites. With increasing of copper cations, the iron cations immigrate to tetrahedral site, consequently the saturation magnetization decrease.

---

In the present study, pure Aluminum powder with 5%wt Titanium Dioxide was mechanically milled at different times. Using phase analysis through X-ray diffraction (XRD), it was found that increasing of the milling times over 10 hours causes the reduction of Titanium by Aluminum and formation of Al2O3 in the structure. Also, it was shown that if the process persists, Aluminum reacts with Titanium and causes the formation of Al3Ti in the composition. The reactions were studied through the thermodynamic relations. Furthermore, after distribution of reinforcement particles in the matrix, using X-ray diffraction peak broadening, according to Williamson-Hall equation, the mean crystallite size and lattice strain were determined, and by scanning electron microscopy (SEM), the structure and morphology of the powder particles were studied.

---

Silicon nitride has attracted a considerable attention because of its excellent properties such as high-temperature strength, good oxidation resistance, high corrosion resistance, good thermal shock resistance, high creep resistance and good thermal and chemical stability. There are several different fabrication methods for synthesizing Si3N4 particles. Such methods are mostly costly and kinetically slow and require lengthy heat treatment. In this study, Si3N4 compounds were synthesized by means of mechanical milling. In the mechanical milling route,Si powder (≤99.0%) was milled under nitrogen gas for 25 h and heated at various temperatures 1100-1200-1300 and 1400 C for 1 h at the nitrogen atmosphere at a rate of 200 ml/min. Silicon powder was also annealed under a similar condition in order to evaluate the impact of milling process on the low temperature synthesizing of Si3N4. Phase identification and microstructural characteristics of products were evaluated by X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy. The Fourier transform infrared spectroscopy and thermal analysis were used for characterization of the formed bands and thermal treatment of the sample, respectively. The obtained results exhibited that Si3N4 powder was fully formed with two kinds of morphologies including globular particles and wire with a width of 100–300 nm and length of several microns at sintering temperature of 1300 C. This was confirmed by the Si–N absorption bonds in the FTIR trace. Based on XRD results, 25 h milling reduced temperature of reaction remarkably in comparison with direct nitridation of Si powders for 1 h. With an increase in the reaction temperature, the Si3N4 samples had a phase transformation 𝛂→𝛃, and variation of the morphology followed the vapor–liquid -solid mechanism.

---

The aim of this investigation was to produce Ti47Al48Mn5 intermetallic compounds with different microstructures in order to study their oxidation behavior. The reason for selecting manganese as an alloying element was to enhance the toughness of the compound. Ti47Al48Mn5 alloys were obtained through mechanical alloying, cold pressing and heat treatment. XRD results showed that milling of the elemental powder mixture for 30 hours causes the formation of Al and Mn in Ti solid solution, while by increasing milling time up to 50 hours, amorphization of powder mixture occurs. To obtain duplex and fully lamellar microstructures, the mechanically alloyed powders were cold pressed and then heat treated at 1100 °C and 1400 °C in argon atmosphere for 50 hours, respectively. The results of the oxidation test at 1000 °C revealed that the different microstructures of Ti47Al48Mn5 alloy investigated in this study have little effect on the oxidation resistance, and similar oxidation mechanisms existed for the two microstructures.

---

Mullite and alumina are common in high-temperature applications because of their low thermal expansion coefficient and good thermal shock resistance. Evolution of SiC in the matrix and using it as reinforcing phase can improve thermo-mechanical properties of these materials. Also, in-situ formation of the reinforcing phases by using inorganic materials is an economical process. In this work, crystallization of SiC as reinforcing phase in the matrix of mullite-alumina by carbothermal reaction processes of inorganic materials (andalusite and kaolinite) was studied. According to the ratio of C/SiO₂ and process conditions, some properties of the composite such as phase transformation, microstructure and physical and mechanical properties were investigated. The results showed that optimal ratio of C/SiO₂ and firing temperature of densification to form SiC crystals were 3.5 and 1600^°C for andalusite and 5.5 and 1500^°C for kaolinite.

---

Nanoparticles of Mg–Co–Ti substituted strontium hexaferrite with nominal composition of SrFe_12-2x(Mg,Co)_0.5x Ti_xO₁₉ (x=0-2.5) were synthesized by a co-precipitation method. The structural, magnetic and electromagnetic properties of samples were studied as a function of x by thermal gravimetric (TG), X-ray diffraction (XRD), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM) and vector network analysis. It was found that the synthesis temperature increases with an increase in Mg–Co–Ti substitution and hence the particle size decreases. The XRD results showed that whole samples had good crystallinity and with an increase incations, the impurity phase of Fe₂O₃ appears. The results of hysteresis loops indicated that the saturation of magnetization of ferrite decreases from 40 emu/g to 19 emu/g with an increase in x. The Mössbauer spectroscopy showed that the cations are substituted in the 12k site of magnetoplumbite structure. Vector network measurements showed that the doped samples had much more effective reflection loss values than those of undoped ferrites. As a result, Mg–Co–Ti doped Sr-hexaferrites with x=2 can be proposed as suitable absorbers for applications in microwave technology with a good deal of consistency.

---

In the present research NdFeB thin films coupled with buffer and capping layer of W were formed on Si/SiO₂ substrate by means of RF magnetron sputtering. The system was annealed at vaccum at different temperatures of 450, 500, 550,. 600 and 650 °C Phase analysis was carried out by XRD and it was found that NdFeB was formed without the formation of any kind of secondary phase. The cross sectional and grain size of the thin films were measured by scanning electron microscopy. Morphological studies were performed by atomic force microscopy. Magnetic properties of thin films including coercivity, saturation of magnetization and hysteresis area were evcaluated by vibrating sample magnetometer. It was found that by annealing at 400 °C the amorphous layer was formed.The highest intensity of peaks was formed at 550 °C and with an increase in temperature the intensity was declined. The grain size was increased by temperature and had an impact on the coercivity. With an increase of temperature up to 600 °C, perpendicular coercivity was increased and then by further increase of temperatute, coercivity was reduced. Based on the obtained data the temperature of 600 °C was selected as the optimum annealing temperature for reaching enhanced structural and magnetic feature.

---

In this study, nine Nd-Fe-B and FeCe thin films with 10-50 nanometers width were prepared by RF magnetron sputtering on the Si/SiO₂ substrate. Then, the films were annealed at 800 ^oC for 5 sec in rapid thermal annealing furnace. X-ray diffractometry (XRD) was used to analyze the phase composition of layers and existance of Nd₂F₁₄ and Fe₆₅Co₃₅ phase was confirmed, without formation of any other secondary phase. The layers surfaces were investigated using Field Emission Scanning Electron Microscope (FESEM). The morphology of layers surfaces was investigated using Atomic Force Microscope (AFM). The magnetic properties of layers were evaluated by vibrating sample magnetometer with maximum applied field of 24kOe, in order to measure coercivity, saturation of magnetization, hysteresis area, rectangular ratio and (BH)max. It was found that all layers have vertical magnetic anisotropy. Increasing thickness of FeCo resulted in increasing saturation of magnetization,  coercivity and saturation magnetization. The results indicate that by an increase in thickness of FeCo up to 20nm, exchange interaction strength between hard and soft magnetic layers is enhanced and, consequently, maximum energy induced from this hetero-structure is increased.

---

Organic–inorganic hybrid coatings were prepared by sol–gel method and deposited on aluminum alloy 6061. Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) spectroscopy and Scanning Electron Microscopy (SEM) were used for structural study of the hybrid coatings. Adhesive strength of sol–gel coatings to the substrate was evaluated quantitatively and qualitatively. Corrosion behavior of the samples was studied by cyclic potentiodynamic and linear polarization tests. Results showed that adhesion strength of the coatings to the substrates was increased with increasing tetrapropoxide of zirconium (TPOZ) and cerium content. Corrosion tests showed that corrosion current density of coated samples were decreased three to seven orders of magnitude in comparison with uncoated aluminum alloy 6061. Decreasing in corrosion current density and increasing in polarization resistance was observed by increasing zirconia and cerium content. Unlike the uncoated aluminum alloy 6061, the crack-free coatings did not show pitting tendency. 

---

Simultaneous application of mechanical pressure and electrical charge on powder samples in spark plasma sintering process, has resulted in a sample with a density close to the theory. In the present study, a thermal-electrical-mechanical coupled finite element model of spark plasma sintering system using multi-objective optimization algorithm is proposed to optimize the mold variable. The simulation performed for Si₃N₄-SiO₂ (1:1 mol) specimen has good agreement with the experimental results. Multi-objective genetic algorithms was used for optimization of mold design in order to maximize the temperature of sample core and minimize the mises stress in the mold. The results show that the optimized dimensions cause 8% increase in sample temperature and about 18% decrease in temperature difference between mold surface and sample core. This leads to better uniformity in the porosity distribution of final sample.

---

---

---

---

---

---