Showing 9 results for M.A. Golozar
A. Najafi- Zadeh, M.a. Golozar,
Volume 8, Issue 1 (4-1990)
Abstract
M.a. Golozar, A. Najafi- Zadeh,
Volume 13, Issue 1 (7-1993)
Abstract
M.a. Golozar,
Volume 14, Issue 1 (1-1994)
Abstract
Kiani Rashid, A. Najafi- Zadeh, M.a. Golozar,
Volume 14, Issue 1 (1-1994)
Abstract
M.h. Fathi, V. Mortazavi, M.a. Golozar and K. Khosravi,
Volume 15, Issue 1 (7-1994)
Abstract
Tarnish and Corrosion behavior of three Commercial dental amalgams namely Am.1, Am.2, Am.3, have been investigated by utilizing in vitro tests. The corrosion and/or dissolution rate of the three dental amalgams were studied in 0.9 wt% NaCl Solution, artificial saliva and Ringer's solution. Potentiodynamic polarization technique was employed to study cathodic and anodic polarization behavior, from which the corrosion potentials and corrosion current densities were calculated. The corrosion potential and the corrosion current density of each amalgam was found to be affected by the nature of electrolyte used, as well as the Pre-immersion time. However, the order of corrosion potentials and corrosion current densities of the three dental amalgams examined, was found to be independent of the electrolyte used.
A. Said and M.a. Golozar,
Volume 18, Issue 1 (4-1999)
Abstract
Combustion synthesis has been used to produce Fe-(Ti,W)C composites. A simple reactor was designed which made it possible to ignite the samples under controlled atmosphere. Samples with different W/Ti ratio were ingnited under argon atmosphere by an electric arc and a self-propagating reaction was initiated in each sample. Different composites such as WC in Fe-Ti matrix, WC+(Ti,W)C in Fe matrix, and (Ti, W)C in iron matrix were produced by changing W/Ti ratio in the starting materials. Examination of the microstructure revealed that WC had an angular morphology while (Ti, W)C particles were spherical.
R. Bagheri and M.a. Golozar,
Volume 25, Issue 2 (1-2007)
Abstract
Using Electrostatic Spray Coating Technique, Polypropylene Powder (EPD 60R) was applied on carbon steel substrates at room temperature. In order to obtain a uniform coating, steel substrates with powder coatings were heated in a vacuum oven at various temperatures up to 250° C for various periods of time up to 45 min and a pressure of 200 mb. The coatings produced had thicknesses of around 470 microns. In order to modify the chemical structure of this polymer, the powder coatings containing various weight percentages of maleic (anhydride (MA) and a peroxide (TBHP or DCP) were also applied onto the steel substrates under the above conditions. Adhesion strength, wear resistance, and ductility of polymer coatings produced were assessed using ASTM standard methods. Results obtained revealed that the polymer coating containing 5 wt%. MA and 0.1 wt% TBHP had the best mechanical properties. Adhesive strength and wear resistance of this coating were 14.3 kgf and 250.3 cm, at 6 kgf, respectively, under the applied load of 6kg. Results obtained from DSC thermographs and IR Spectroscopy also proved the chemical bond formation (grafting) between the polymer and MA. The mechanical properties of coatings on steel substrate stem from such graftings.
A. Fattah-Alhosseini, A. Saatchi, M.a. Golozar, K. Raeissi, B. Bavarian,
Volume 32, Issue 2 (Dec 2013)
Abstract
In this study, effect of potential on composition and depth profiles of passive films formed on 316L stainless steel in 0.05 M sulfuric acid has been examined using X-ray photoelectron spectroscopy (XPS). For passive film formation within the passive region, four potentials -0.2, 0.2, 0.5, and 0.8 VSCE were chosen and films were gown at each potential for 60 min. XPS analysis results showed that atomic concentration of Cr and Fe initially increase (E < 0.5 VSCE) and then decrease with potential. This decrease is due to surface dissolution of the Fe and Cr oxides. For both alloying elements, Ni and Mo, no obvious change in atomic concentration was showed. Results indicated that at higher potentials, before entering transpassive region, oxidation of Cr3+ to Cr6+ is happened.
M.r. Garsivaz Jazi, M.a. Golozar , K. Raeissi,
Volume 33, Issue 3 (Journal of Advanced Materials- winter 2015)
Abstract
In this study, the chemical composition, thickness and tribocorrosion behavior of oxide films prepared on Ti-6Al-4V alloy by anodising treatment in H2SO4/H3PO4 electrolyte at the potentials higher than the dielectric breakdown voltage were evaluated. The thickness measurement of the oxide layers showed a linear increase of thickness by increasing the anodizing voltage. The EDS analysis of oxide films demonstrated precipitation of sulfur and phosphor elements from electrolyte into the oxide layer. Tribocorrosion results indicated that the tribocorrosion behavior of samples was significantly improved by anodising
process. Furthermore, the tribocorrosin performance of thesamples anodised at higher voltages was enhanced. SEM and EDS of worn surfaces indicated that the oxide layer on the samples anodised at lower voltages was totally removed, but for the samples anodised at higher voltages, the oxide layer was only locally removed within the wear track. Moreover, measurement of wear volume of the treated samples exhibited lower values on the samples anodised at higher voltages.
