Showing 6 results for Bone
M. Raz, F. Moztarzadeh, M.a. Shokrgozar, M. Ashuri, M. Tahriri,
Volume 32, Issue 2 (12-2013)
Abstract
In this project, we prepared biomimetic nanocomposite scaffolds from gelatin and chitosan and hydroxyapatite and subsequently the scaffolds were evaluated by common used bulk technique. For this purpose, the nanocomposite hydrogel/apatite bone tissue engineering scaffolds were fabricated using applied biomimetic method accompanied with freeze drying technique. The apatite was precipitated using double diffusion mechanism within gelatin hydrogel in similar pH and temperature to the human body. Chitosan initial percentage (20, 30 and 40%) was set as variables. Nanocomposites were soaked in glutaraldehyde solution in order to enhance mechanical properties and make them insoluble in water. Diffusion of calcium and phosphate from lateral hydrogel into the middle hydrogel caused formation of parallel white layer-formed precipitate. Analysis of precipitates formed within middle hydrogel for the samples, showed that detected materials are composed of carbonated hydroxyapatite and dicalcium phosphate dihydrate (DCPD, brushite). Also, mechanical behavior obtained for the scaffolds were comparable with spongy bone. With increasing chitosan in the composite scaffold, the water up-take was increased from 379 to 661%. Phase composition, microstructure and structural groups in the composite samples were also characterized by X-Ray Diffraction (XRD), scanning electron microscopy (SEM) and Fourier transform infra-red (FTIR) analyses. Eventually, the obtained results showed that the composite contains 20% chitosan had appropriate properties for fabricating bone scaffold.
S. Mohammadi, A. Doostmohammadi, M.r. Saeri,
Volume 34, Issue 1 (5-2015)
Abstract
The positive effect of Si and Zn ions on bone formation and metabolism has already been confirmed. The aim of this study was preparation and characterization of Willemite (Zn2SiO4) for the repair of bone defects. Willemite was prepared through solid state reaction. Phase analysis and chemical compositions were investigated. The zeta potential of the nanoparticles was determined in physiological saline, and compressive strength and Young's modulus of the samples were measured. The ability of hydroxyapatite formation was investigated in simulated body fluid (SBF) and cytotoxicity of the particles was evaluated in contact with human bone marrow stem cells. The results of this study showed that Willemite nanobioceramic is obtained with the expected chemical composition and negative zeta potential. The results also showed that the hydroxyapatite forming ability in SBF was not strong. MTT assay confirmed the cell proliferation and availability in contact with a specific concentration of Willemite nanoparticles. All these findings indicate that Willemite nanobioceramic with proper biocompatibility can be suggested as a novel biomaterial for the repair of bone defects.
M. Kouhi, M. Shamanian, M. Fathi, Molamma Prabhakaran, Seeram Ramakrishna,
Volume 36, Issue 3 (11-2017)
Abstract
In this work, poly (hydroxybutyrate co hydroxyvalerate) (PHBV) composite nanofibrous scaffold containing hydroxyapatite/bredigite (HABR) nanoparticles was fabricated through electrospining method. The morphology of prepared nanofibers and the state of the nanoparticles dispersion in nanofiber matrix were investigated using scanning and transmission electron microscopy, respectively. Evaluation of the mechanical properties of the nanofibrous scaffolds revealed that there is a limit to the nanoparticle concentration at which nanoparticles can improve the mechanical properties of the nanofibrous scaffolds. According to the results, PHBV/HABR nanofibers showed higher wettability compared to PHBV nanofibers. In vitro cell culture assay was done using human fetal osteoblast cells on nanofibrous scaffold. MTS assay revealed that cell proliferation on the composite nanofibrous scaffold was significantly higher than those on the pure scaffold after 10 and 15 days. Scanning electron microscopy- Energy dispersive X-ray spectroscopy and CMFDA colorimeter assay analysis showed that the cells on the PHBV/HABR scaffolds acquired higher mineral deposition than the cells on the pure PHBV and control sample scaffold. Based on the results we concluded that PHBV/HABR nanofibers scaffold with higher wettability, improved mechanical properties and cell behavior hold great potential in bone regeneration applications.
S. Sadeghzade, R. Emadi, Sh. Labbaf,
Volume 37, Issue 1 (6-2018)
Abstract
In the recent three decades, Ca-Si-based ceramics have received great attention as an appropriate candidate for tissue engineering applications due to their remarkable bioactivity, biocompatibility, and good bone formation ability. Hardystonite is currently recognized as a bioactive and biocompatible bio-ceramic material for a range of medical applications. In the present study, for the first time, hardystonite powder and 3D hardystonite scaffold with interconnected porosity were produced using mechanical alloying synthesis and the space holder method, respectively. It was found that pure nano-crystalline hardystonite powder formation occurred following 10 h of milling and subsequent sintering at 800 C° for 3 h. The measured crystallite size of particles and the hardystonite scaffold was found to be 28 ± 2 and 79 ± 1 nm, respectively. The results also showed that nanostructured hardystonite scaffolds with the compressive strength and modulus of 0.35 ± 0.02 and 10.49 ± 0.21 MPa, the porosity of 81 ± 1% , and pores size range of 200–500 μm were successfully synthesized after sintering at 1250 °C for 3 h. During the sintering process, NaCl (80wt%, 300-420 µm), as the spacer agent, gradually evaporated from the system,producing porosity in the scaffold. Simulated body fluid (SBF) was used to evaluate the apatite formation ability of the scaffolds. The results showed that the formation of an apatite layer on the scaffold surface could be considered as a bioactivity criterion.
S. F. Shams, M. Ebrahimian-Hosseinabadi,
Volume 37, Issue 2 (9-2018)
Abstract
The purpose of this paper was modeling and mechanical analysis of the biodegradable biphasic calcium phosphate/silk (BCP/Silk) laminated composite bone plate for fractured tibia healing; to this aim,ABAQUS 6.13 was employed for modeling and mechanical analysis. First, the tibia bone was considered based on the anthropometric measurements of an average person as a two-layer cylinder; the inner part was the bone marrow and the outer one was the cortical bone. Then, the bone plate and screws were designed according to the defined standards and the properties of new composite in the ABAQUS software. The mesh of bone plate and other equipments were selected to be tetragonal and cubic, respectivelly. After that, the bone plate was placed on the bone while the bone was bounded along the Y axis and the force of around 400 N was loaded. The results showed that the biocompatible and biodegradable composite bone plate had the elastic modulus of about 21 GPa, which was close to the bone modulus.
F. Fareghdeli, M. Karimi, A. Novin, M. Solati-Hashjin,
Volume 40, Issue 3 (11-2021)
Abstract
One challenge in preparing polymer/ceramic composites is non-uniform ceramic particles distribution in a polymer matrix. This research evaluated the effect of stirring time and temperature on hydroxyapatite (HA) distribution through (polylactic acid) PLA matrix. Therefore, to mix the ceramic suspension with the polymer solution, three temperatures, namely 25, 37, and 45°C and four times including 6, 12, 24 and, 48 h were examined. Fourier-transform infrared spectroscopy (FTIR) analysis was used to investigate the bonds, which showed physical bond formation such as carboxyl-calcium-carboxyl between HA and polymer matrix, influenced on particles distribution. Scanning electron microscopy (SEM) and Energy-dispersive X-ray spectroscopy (EDS) were used to observe particles distribution and determine samples homogeneity. To fulfill this goal, each obtained photograph representing the calcium presentation was split into nine equal sections, and a method based on the newly defined index called dispersion factor “α” was used to analyze the distribution. Results showed that the sample prepared at 37°C and 48 h had the topmost homogeneity properties.