Search published articles


Showing 3 results for Hardness.
Effect of Equal Channel Angular Pressing on Microstructure of AM30 Magnesium Alloy
R. Jahadi Naeini, M. Sedighi, H. R. Jahedmotlagh,
Volume 33, Issue 3 (3-2015)
Abstract
In this paper, the effect of Equal Channel Angular Pressing (ECAP) process on the structure and mechanical properties of AM30 magnesium alloy was studied. The results showed a considerable effect of ECAP process on creating an ultrafine grain size structure. Scanning Electron Microscope indicated that the grain size dropped from 20.4 µm in the extruded form to 7.2 µm in the first pass and 3.9 µm in fourth pass. The fourth pass presented higher ductility and lower yield stress in comparison with the extruded case. This behavior can be explained based on higher rate of texture softening versus the effects of the grain refinement on strength. The hardness test on the samples cross-section showed an increase in hardness and a uniform strain distribution at higher ECAP passes.
Kinetics of Austenite Layer Growth on the Surface of Fe-23Cr-2.4Mo Ferritic Stainless Steel During Solution Nitriding
Kh. Farjam Hajiagha, A. R. Akbari, R. Mohammadzadeh,
Volume 36, Issue 2 (9-2017)
Abstract

In this study, the kinetics of austenite layer growth on the surface of Fe-23Cr-2.4Mo ferritic stainless steel during solution nitriding and the effects of nitrogen adding on microstructure and hardness of the steel have been investigated. Steel plates of 2 mm thick were solution-nitrided at 1200˚C under nitrogen pressure of 0.25 MPa for 2, 3, 6, 9, 12 hours. Microstructure, the thickness of austenite layer and the hardnes of the nitrided samples, were investigated by using optical microscope, X-ray Diffraction (XRD) and microhardness measurements. The results showed that during solution nitriding, nitrogen diffuses through the lattice and grain boundaries and transforms ferrite to austenite phase, with average nitrogen diffusion coefficient of 6.54×10-5 mm2s-1. The thickness of the austenite layer formed on the samples surfaces increased proportional to the square root of the nitriding time, so that after 12 hours niriding, the whole thickness of the ferritic sample with hardness of 262 HV0.1 transformed to austenite with hardness of 420 HV0.1.


Investigation of the Effect of Homogenization Treatment on Distribution of Alloying Elements, Microstructure and Hardness of Co-Al-W-Ti-Ta-Base Superalloy
M. Etminan, M. Morakabati, S. M. Qazi Mir Saeid,
Volume 39, Issue 2 (8-2020)
Abstract
The aim of this study was to investigate the effect of temperature and time of homogenization treatment on the microstructure, distribution of alloying elements and hardness of the novel Co-based superalloy Co-7Al-7W-4Ti-2Ta. For this purpose, the specimens were first homogenized at 1250 and 1300 °C for 2, 4, 6 and 8 hours and then water-cooled. Subsequently, the specimens were subjected to hardness testing and microstructural examinations by optical and electron microscopy. The results showed that by increasing the homogenization temperature to 1300 °C, the porosity created by Ti oxidation and local melting of the Co-Al-Ti eutectic compounds led to a decrease in hardness to 90 Vickers. This phenomenon was due to high segregation of alloying elements in the cast structure. The intensity and destructive effects of this segregation were reduced by remelting of alloy. However, by homogenization at 1250 °C, no local melting of eutectic zones or porosity were observed in the specimens and a more uniform structure was obtained with increasing time. Minimum and maximum hardness values after homogenization at 1250°C were 348 and 406 Vickers, respectively. Moreover, the microstructure became more homogenous by increasing the homogenization treatment time at this temperature.

Page 1 from 1     

© 2024 CC BY-NC 4.0 | Journal of Advanced Materials in Engineering (Esteghlal)

Designed & Developed by : Yektaweb