Showing 8 results for Hybrid
M. Tehrani Dehkordi, S. H. Bahrami, R. Nategi Jahromi,
Volume 33, Issue 3 (3-2015)
Abstract
In this study, the effects of different parameters on charpy impact properties of pure and hybrid composite laminates reinforced with basalt and glass filaments were investigated. For this purpose, five types of basalt and glass laminates with
quasi-isotropic stacking sequence, namely, a pure basalt, a pure glass, two inter-ply hybrid and one intra-ply hybrid composites were produced. Epoxy resin was used as matrix material. After that, the impact test was performed and the average absorbed energy of each type of specimens was determined. The results indicated that the pure basalt and nylon laminates had the highest and least absorbed energy, respectively. The hybrid laminates had the absorbed energy somewhere between the pure basalt and glass ones. Also, between the hybrid composites, the intra-ply laminate had a better impact performance than the inter-ply ones.
M. Dehestani, L. Zeidabadinejad, S. Pourestarabadi,
Volume 34, Issue 4 (3-2016)
Abstract
In this study, energy and chemical interaction of ZnO and CdS surfaces interfaced with metal-organic framework (MOF), to improve their properties, have been investigated using density functional theory (DFT). Results show that reformation of structures by hybridation with MOF can increase their stability and improve their properties. Comparison of ZnO and CdS structures predict that deposition of MOF on ZnO substrate can be more effective.
M. Bahrami, G.h. Borhani, S.r. Bakhshi, A. Ghasemi,
Volume 35, Issue 3 (12-2016)
Abstract
Organic–inorganic hybrid coatings were prepared by sol–gel method and deposited on aluminum alloy 6061. Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) spectroscopy and Scanning Electron Microscopy (SEM) were used for structural study of the hybrid coatings. Adhesive strength of sol–gel coatings to the substrate was evaluated quantitatively and qualitatively. Corrosion behavior of the samples was studied by cyclic potentiodynamic and linear polarization tests. Results showed that adhesion strength of the coatings to the substrates was increased with increasing tetrapropoxide of zirconium (TPOZ) and cerium content. Corrosion tests showed that corrosion current density of coated samples were decreased three to seven orders of magnitude in comparison with uncoated aluminum alloy 6061. Decreasing in corrosion current density and increasing in polarization resistance was observed by increasing zirconia and cerium content. Unlike the uncoated aluminum alloy 6061, the crack-free coatings did not show pitting tendency.
M. Hajfarajzadeh, A. Eshaghi, A. Aghaei,
Volume 37, Issue 4 (3-2019)
Abstract
A TEOS-GPTMS nano-hybrid thin film was deposited on the polymethyl methacrylate (PMMA) substrate by a sol-gel dip coating method. Morphology, roughness and surface chemical bonding of the thin films were evaluated by X-ray diffraction (XRD), field emission scanning electron microscopy(FE-SEM), atomic force microscopy, and Fourier transform infrared spectroscopy methods, respectively. UV-vis spectrophotometer was used to measure the transmittance spectra of the samples. Also, the adhesion and hardness of the coatings were investigated using pencil hardness the adhesion tape test and the test, respectively. XRD results proved that the thin film had an amorphous structure. Also, FE-SEM images indicated that addition of GPTMS to the TEOS yielded a crack-free thin film. Based on the UV-vis spectroscopy results, the transmittance of the polymer substrate in the visible region was increased by the deposition of the nano-hybrid coating. Moreover, the hardness of the PMMA substrate was increased from 3H to 6H by the deposition of the nano-hybrid thin film. Also, tape test confirmed the high adhesion of the nano-hybrid thin film on the PMMA substrate. Consequently, the transparent organic-inorganic GPTMS-TEOS hybrid coating can be used as a scratch resistant coating on the PMMA substrate.
M. Zadali Mohammad Kotiyani, Khalil Ranjbar,
Volume 38, Issue 1 (6-2019)
Abstract
In this research, an in-situ hybrid composite reinforced by Al3Zr and Al3Ti aluminide particles was fabricated by friction stir processing (FSP). The base metal was in the form of a rolled Al 3003-H14 alloy sheet, and zirconium and titanium metal powders were used as the reinforcements. Six passes of FSP were applied. Tensile strength and hardness of the base metal, as well as FSPed samples before and after applying heat treatment, were determined. Microstructural examinations were performed using optical and scanning electron microcopy (SEM), and phase formation was identified by X-Ray diffraction. Microstructural examination revealed that by applying FSP, the prior large and elongated grains of the base metal were converted to the fine and equiaxed grains. It was also observed that chemical reactions occurred at the interface between the aluminum matrix and the metallic powders, forming in-situ aluminides of Al3Zr and Al3Ti. The post annealing heat treatment activated these solid state chemical reactions and more aluminides were formed. It was also found that the heat treated hybrid composite possessed the highest tensile strength and hardness values. The tensile strength in such samples reached 195 MPa, as compared to 110 MPa of the base metal.
M. Tehrani, H. Nosraty, A. Lorak,
Volume 38, Issue 3 (12-2019)
Abstract
Due to their sensitivity to impact-induced delamination, woven fabric reinforced polymer composites have limited practical applications. Hybridization of polymer composites has been proposed as a solution to this problem. In this study, the effects of fiber reinforcement type, hybridization method, plies stacking sequence and loading rate on mode I delamination behavior of pure basalt, pure nylon, inter-ply and intra-ply hybrid (basalt/nylon) composites were investigated. Composites were length during its propagation in composite samples was measured by mode I delamination test. The inter-laminar fracture toughness of composite specimens was calculated using modified double-cantilever beam theory and the results were compared by statistical methods. A 30 to 80% improvement in the critical fracture toughness of intra-ply hybrid composite compared to pure ones was recorded. Moreover, the delamination initiation load decreased significantly by increasing the loading rate.
S. Borhani Esfahani, H. R. Salimi Jazi, M. H. Fathi, A. Ershad Langroudi, M. Khoshnam,
Volume 40, Issue 1 (5-2021)
Abstract
In this research, a kind of environmentally-friendly inorganic-organic hybrid nanocomposite coating based on silica containing titania/silica core/shell nanoparticles was synthesized and characterized for conservation of facade tiles in historical buildings. The matrix of the composite was prepared by sol-gel process via two methods of ultrasonic and reflux stirring. Tetraethyl orthosilicate (TEOS) and poly-dimethyl siloxane hydroxy-terminated (PDMS-OH) were used for the formation of silica network and creation of flexibility and hydrophobicity, respectively. Titania nanoparticles were used in the form of titania/silica core/shell as ultraviolet absorber. The synthesized nanocomposite was applied on the microscope slides and tiles by dip coating technique. The properties of nanoparticles and coatings were characterized by Fourier-transform infrared spectroscopy (FTIR), Transmission electron microscopy (TEM) and water contact angle measurement. The results revealed that formation of titania/silica core/shell structure was successful. The investigation of PDMS content effect on transparency, cohesion and hydrophobicity of the coating confirmed that the optimum content of this siloxane was around 20 wt.%. In general, the results showed that the silica-based hybrid nanocomposite reinforced with TiO2/SiO2 core/shell nanoparticles could produce a transparent and hydrophobic coating for tile and glass protection.
B. Sharifian, G. H. Borhani, E. Mohammad Sharifi,
Volume 41, Issue 2 (11-2022)
Abstract
In this study, mechanically milled (MM) Al-24TiO2-20B2O3 powder in molten Al7075 matrix was used in order to fabricate in-situ TiB2 and Al2O3 reinforcements in Al7075 matrix. Differential thermal analysis (DTA) examination was adopted to find reaction temperature between milled Al, TiO2, and B2O3 powders. X-Ray Diffraction (XRD) patterns showed the existence of TiB2 and Al2O3 peaks (750 °C at Ar atmosphere) in MM powder. Scanning Electron Microscopy (SEM) results revealed the uniform distribution of TiO2 and B2O3 particles in the aluminum matrix. 6 wt.% MM powder was added to molten Al7075 at 750 °C. The molten Al7075/TiB2-Al2O3 composite was poured in copper mold. The stir casted composites were hot extruded at 465 °C with extrusion ratio of 6:1 and ram speed of 5 mm/s. The microstructures (optical microscopy and TEM) and mechanical properties (hardness and tensile testing) of samples were evaluated. TEM results showed that in-situ TiB2 nanoparticles were formed. The tensile strength of extruded Al7075/TiB2-Al2O3 composite was reached the value of 496 MPa. This result was around four times greater than that of the as cast Al7075 alloy.
