Showing 13 results for Mn
M. Rezaiee – Pajand and S. Payman,
Volume 21, Issue 2 (1-2003)
Abstract
This paper discusses the effective length factor of columns in Khorjini frames. In order to find this factor, a proper approximated method is proposed. In addition, accurate analysis is performed and the results are compared with those from the proposed technique. The comparison demonstrates the accuracy of presented FORMULATIONS. The proposed method is similar to Julian and Lawrence's, which is used for rigid frames.
Keywords: Khorjini Frame, Effective Length, Bifuraction Load, Rotational Stiffness, Matrix Structural Analysis, Column Factor.
M. R. Banan and A. Fouladi,
Volume 22, Issue 1 (7-2003)
Abstract
This paper presents a new super-element with twelve degrees of freedom for latticed columns. This elements is developed such that it behaves, with an acceptable approximation, in the same manner as a reference model does. The reference model is constructed by using many Solid elements. The cross section area, moments of inertia, shear coefficient and torsoinal rigidity of the developed new element are derived. Since the reference model has a large number of degrees of freedom (especially for nonlinear cases), computation of the equivalent essential parameters of the proposed element is very time consuming, so, a model using only beam elements is also presented. For the super element, a general purpose program is developed that is capable of performing linear and nonlinear analysis of 3D-frames with latticed columns. In order to derive the essential parameters of the proposed super-element, many latticed columns are analyzed while shear deformations are taken into consideration. Using these essential equivalent parameters approximate relations are proposed for the compution of parameters of any latticed column based on geometric characteristics. Finally, to show the accuracy of the proposed element, several examples are presented.
Keywords: Finite elements, Super-element, Latticed column, Shear deformations, 3D-frames
J. Emadi,
Volume 24, Issue 1 (7-2005)
Abstract
Being economical and performing well under cyclic loads, steel sections filled with concrete have been widely used in structural buildings. Extensive studies and experiments have been conducted to investigate the influence of different parameters and loadings on the behavior of these structural components. Based on the data available from previous experiments and studies, this paper discusses the behavior of composite columns. The results of 3D-non-linear finite element analysis of thin-walled steel sections filled with concrete are presented. Lastly, comparisons are made between results from finite element analysis and experimental data available about the specimens. Using a trial and error method, the finite element model was calibrated and was used to evaluate the capacity of specimens that were not tested in the laboratory. The capacities of the sections were calculated
based on the LRFD design method. The results are compared to evaluate the accuracy of the proposed method. Because of the increase in the use of high strength materials in structures, the effects of increase in concrete and steel strengths on the behavior of composite columns are discussed in this paper. Also the effects that the change in the thickness of the steel shell may have on the behavior of composite columns are argued.
M. Sheikhi and H. Haji-Kazemi,
Volume 25, Issue 2 (1-2007)
Abstract
Jacketing of reinforced concrete columns is a common and useful strengthening method. This method substantially improves mechanical properties of the column, such as flexural strength as well as shear and ductility. In this paper, the behavior of confined reinforced concrete columns are investigated. The results indicate that the method is more effective for slender columns in the region of their failure zone.
M. R. Tabeshpour, A. A. Golafshani, A. Bakhshi, and A. Moayed Alaei,
Volume 25, Issue 2 (1-2007)
Abstract
The assessment of seismic performance of existing structures is becoming an important problem in earthquake engineering. Some important ructures are considerably old and, therefore, their strengths and ductilities are less than strength and ductility demands because of changes in codes and design methodologies. Such structures must be strengthened to resist future earthquakes. First, a structural model must be developed and then, based on seismic hazard and seismic risk analysis or code quantities, the design (or control) parameters can be determined. The next step is defining the damage indices in order to quantify the structural damage. Then the nonlinear dynamic analysis is carried out and damage indices are calculated. In the present paper, a power plant stack (located in Mashhad) is investigated for some levels of peak ground acceleration (PGA) considering return periods of 75, 500, 1000, and 2500 year. The height of stack is 100 m and the external diameter of the structure is 10 m. Several records are used for nonlinear dynamic analysis. It has been used from Park-Ang damage index that is a suitable model for concrete structures and has been considered in IDARC. It is clear that nonlinear dynamic analysis is necessary for the seismic vulnerability of existing structures. Special structures such stacks can be modeled with some 2-D or 3-D elements. However, the beam-column element is a proper model for special structures such as chimneys, considering calculation cost.
M. Haerifar, M. Zandrahimi,
Volume 34, Issue 1 (5-2015)
Abstract
In the present study, 304 stainless steel (SS) was electrochemically plated with nanocrystalline Mn-Cu alloy coatings from a bath containing ammonium sulfate. The effects of current density on the microstructure, crystallographic structure, and chemical composition of the deposits were studied. The results showed that at low current densities, discontinuous coatings with a large amount of Cu can be obtained. Further increase in current density resulted in amorphous, compact and heterogeneous coatings with a small amount of Cu. The presence of Cu at low contents in precipitated coatings delayed the phase transformation of as-deposited ductile g-Mn to the brittle and hard a-Mn. However, the results did not show any specific changes in the grain size of the coatings with variation of current densities.
A. Zare, M. Hadi, A. Ghasemi, H. Karimi , M. Sadeghi,
Volume 34, Issue 2 (7-2015)
Abstract
The aim of this investigation was to produce Ti47Al48Mn5 intermetallic compounds with different microstructures in order to study their oxidation behavior. The reason for selecting manganese as an alloying element was to enhance the toughness of the compound. Ti47Al48Mn5 alloys were obtained through mechanical alloying, cold pressing and heat treatment. XRD results showed that milling of the elemental powder mixture for 30 hours causes the formation of Al and Mn in Ti solid solution, while by increasing milling time up to 50 hours, amorphization of powder mixture occurs. To obtain duplex and fully lamellar microstructures, the mechanically alloyed powders were cold pressed and then heat treated at 1100 °C and 1400 °C in argon atmosphere for 50 hours, respectively. The results of the oxidation test at 1000 °C revealed that the different microstructures of Ti47Al48Mn5 alloy investigated in this study have little effect on the oxidation resistance, and similar oxidation mechanisms existed for the two microstructures.
F. Nazari, M. Hakimi, H. Mokhtari, A.s. Esmaeily,
Volume 35, Issue 2 (9-2016)
Abstract
In this paper, milling was investigated as a method for production of Mn-Ga binary alloys and the effect of milling process on phase formation of Mn:Ga samples with 2:1 and 3:1 ratio within 1, 2 and 5 hour milling times was studied. For Mn:Ga samples, according to the results, Mn1.86Ga compound with tetragonal structure and I4/mmm space group was a stable phase. Also, some amounts of Mn3Ga compound with orthorhombic structure and Cmca space group was observed in the Mn:Ga solution. The effect of Ge addition, with the purpose of replacing Ge with Ga was also studied in Mn:Ga:Ge (3:0.5:0.5) sample. Although improved magnetic properties is expected with the addition of Ge, but increasing the coercivity was occurred, and saturation magnetization did not change significantly in the studied sample. Ge addition caused elimination of the possibility of formation of asymmetric orthorhombic Mn3Ga phase. In return, two new structures of Mn11Ge8 and MnGaGe were appeared. This phase change was confirmed by studying magnetic behaviour of samples. This behavior can be caused by unbalanced electrostatic forces resulting from Mn-Mn exchange interaction in Mn3Ga orthorhombic structure and substitution of some Ge atoms with Ga.
S.t. Mohammadi Benehi, S. Manouchehri, M.h. Yousefi,
Volume 35, Issue 3 (12-2016)
Abstract
Magnesium-manganese ferrite nanopowders (MgxMn1-xFe2O4, x=0.0 up to 1 with step 0.2) were prepared by coprecipitation method. The as-prepared samples were pressed with hydrolic press to form a pellet and were sintered in 900, 1050 and 1250˚C. Scanning Tunneling Microscope (STM) images showed the particle size of powders about 17 nm. The X-ray patterns confirmed the formation of cubic single phase spinel structure in samples sintered at 1250˚C. Substituting Mg2+ with Mn2+ in these samples, the lattice parameter decreased from 8.49 to 8.35Å and magnetization saturation decreased from 74.7 to 21.2emu/g. Also, coercity (HC ) increased from 5 to 23Oe and Curie temperature (TC ) increased from 269 to 392˚C. Samples with x= 0.2, 0.4, 0.6 sintered at 1250 ˚C, because of their magnetic properties, can be recommended for hyperthermia applications and for phase shifters.
M. H. Tahmasebi, K. Raeissi, M. A. Golozar, A. Vicenzo, M. Bestetti,
Volume 35, Issue 3 (12-2016)
Abstract
In the present investigation, Mn-Ni binary nano-oxide was deposited by potentiodynamic method on stainless steel at room temperature and the effect of annealing process (at 200 oC for 6 h) on microstructure and electrochemical performance of the synthesized pseudocapacitor was studied. The results showed the significant effect of annealing process on increasing the capacitance and decreasing the charge transfer resistance of the electrode. Field Emission Scanning Electron Miscroscopy (FESEM) images depicted interconnected and random nano-flakes in the oxide film microstructure. Moreover, a partially crystallized structure consisting disorder hexagonal birnessite type phase was formed upon annealing in the deposited oxide film with about 10 %at Ni in composition. Based on the galvanostatic charge-discharge plots, the highest specific capacitance (384 F g-1) and specific energy (53 Wh kg-1) were found at specific current of 0.1 A g-1 for the annealed oxide electrode. Finally, cycle life test results at specific current of 10 A g-1 showed an excellent cyclability and an increase of about 23% in specific capacitance of synthesized pseudocapacitor after 5000 charge-discharge cycles in 1 M Na2SO4.
Kh. Zamani, M. Tavoosi, A. Ghasemi ,
Volume 39, Issue 4 (2-2021)
Abstract
In this research, effect of B and Si addition on the structural and magnetic properties of AlCoCrMnNi high-entropy alloys was investigated. The structural and magnetic properties of AlCoCrMnNiX(X= B, Si) alloys were studied by X-ray diffractometer (XRD), scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and vibrating sample magnetometer (VSM). First, the constituent components of the AlCoCrMnNiX (X=B, Si) alloys were mixed for 10 hours. XRD analysis revealed that the solid solution was not formed by mixing. The alloys were then annealed at 900 ˚C for 10 hours. XRD results revealed formation of a solid solution with BCC structure in AlCoCrMnNi and AlCoCrMnNiB alloys. For AlCoCrMnNiSi and AlCoCrMnNiSiB alloys, Ni2Si and Cr2Si3 intermetallics were formed in addition to the solid solution with BCC structure. VSM results suggested that while forming the solid solution for AlCoCrMnNi alloy, soft magnetic properties improved so that magnetic saturation and coercivity increased from 40.22 to 64.46 emu/g, and from 180.143 to 14.09 Oe, respectively.
M. Judaki, M. Seifollahi, S. M. Abbasi, S. M. Ghazi Mir Saeed,
Volume 40, Issue 1 (5-2021)
Abstract
In this article, the effects of Pr and Nd were investigated on the microstructure and absorption/desorption characteristics of MmNi5 hydrogen storage alloy. The alloys were prepared in Vacuum induction furnace and the microstructures and phases were analyzed using scanning electron microscopy (SEM) equipped with energy dispersive X-ray analysis (EDS) and X-ray diffraction (XRD). Hydrogen absorption/desorption characteristics was performed on Sievert apparatus. The results showed that the microstructure of the alloys consist of matrix, second phase as a result of Al segregation, porosities and cracks. The amount of second phases and Al in this phase in Mm(Pr,Nd)Ni4.7Al0.3 is less than MmNi4.7Al0.3. Al in Mm(Pr,Nd)Ni4.7Al0.3 were more homogenized. Pressure-Composition Isotherms of hydrogen absorption/desorption at 25˚C showed that for MmNi4.7Al0.3 and Mm(Nd,Pr)Ni4.7Al0.3, absorption pressures were 14.52 and 9.90 bar, desorption pressures were 5.53 and 5.49 bar, hydrogen storage capacities were 1.37 and 1.33 wt. % and hysteresis were 0.73 and 0.58, respectively. These results are useful in industrial applications, because of inconsiderable decrease in hydrogen storage capacity and the other positive variation in absorption/desorption characteristics, especially the hysteresis and absorption pressure.
M. Shayestefar, A. R. Mashreghi, S. Hasani ,
Volume 40, Issue 1 (5-2021)
Abstract
Mn0.8Zn0.2Fe2-xDyxO4 (where x= 0, 0.025, 0.05, 0.075, 0.1) ferrite nanoparticles were synthesized by auto- combustion sol-gel method for the first time in this study. The effect of Dy-doping on the structural and magnetic properties of the produced specimens was examined using the X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), vibrating sample magnetometery (VSM), and field emission scanning electron microscope (FE-SEM). The results showed that a cubic spinel structure was formed in all of the synthesized specimens. It was also found that the addition of Dy increased the lattice parameter while decreased the average of crystallites size. Furthermore, the FE-SEM micrographs showed that Dy not only plays an effective role in reducing the agglomeration of nanoparticles and their distribution, but also reduces the average of particle size. It was also observed that the addition of Dy had no effect on the morphology of the synthesized nanoparticles. Investigation of the magnetic properties revealed a clear decrease in the saturation magnetization and coercivity by the Dy addition. So that the saturation magnetization of the samples decreased from 66.3 to 58.4 emu/g and the coercivity decreased from 78.5 to 71.9 Oe.