Showing 5 results for Nanocrystal
M. H. Enayati and M. Salehi,
Volume 25, Issue 2 (1-2007)
Abstract
Fabrication and characterization of aluminum matrix composites containing different volume fractions of Ni3Al powder (5-40 Vol%) were investigated. Ni3Al powder was produced by mechanical alloying of elemental nickel and aluminum powder mixture. Al-Ni3Al composite parts were prepared using a powder metallurgy route involving two stages Al and Ni3Al powder mixtures were first compacted under 500MPa and then hot-pressed under 250MPa at 420 oC for 10min. The microstructure and hardness of consolidated parts were investigated by x-ray diffractometery, optical and scanning electron microscopy and
hardness measurements. Results showed that consolidated Al-Ni3Al samples included no significant porosity with a nearly uniform distribution of Ni3Al particles. Additionally, structural examinations showed that no significant reaction between Ni3Al and aluminum matrix occurred during sintering process. Al-Ni3Al composites exhibited a higher hardness value compared with pure aluminum sample prepared under identical conditions. The hardness value of Al-Ni3Al composites increased linearly as Ni3Al content increased.
T. Mousavi, M. H. Abbasi, F. Karimzadeh, and M. H. Enayati,
Volume 26, Issue 2 (1-2008)
Abstract
S. Mirzaei , A. Jazayeri Gharehbagh,
Volume 31, Issue 1 (6-2012)
Abstract
The soft magnetic nanocrystalline Fe73.5Si13.5B9Cu1Nb3 alloy (FINEMET®) is produced by heat treatment of amorphous precursor. Determining kinetic parameters of amorphous structure transformation to nanocrystalline allows the control of microstructure (e.g. size and volume fraction of nanocrystalline grains) in order to achieve desired soft magnetic properties by optimizing the heat treatment conditions. In this research, the nanocrystallization kinetics of amorphous FINEMET alloy were studied using isoconversional and isokinetic methods under non-isothermal conditions of various heating rates ranging from 5 to 20˚C/min. The changes in the microstructure and magnetic properties of amorphous ribbon during nanocrystallization process were studied using X-ray diffractometry and hysteresisgraph, respectively.
M. Hakimi, P. Kameli, B. Aslibeiki, A. Faqeeh,
Volume 35, Issue 4 (2-2017)
Abstract
In this work, cobalt ferrite nanocrystallites were synthesized by air annealing of milled Co-Fe compound. Effect of annealing temperature on phase formation of cobalt ferrite and structural and magnetic properties of the product was studied. Analysis of annealed sample in 450 oC showed that around 46 weight percent of the specimen was changed to Co2FeO4. This value increased to 95 and 90% for 800 oC and 900 oC annealed samples respectively. Reduction of saturation magnetization under annealing was related to transformation of Co-Fe to cobalt ferrite. Increasing the value of saturation magnetization in 900 oC annealed sample compared to 800 oC one was attributed to decreased surface to volume ratio and crystallite size. The main reason of occurrence of maximum coercivity in 800 oC annealed sample was its low crystallite size.
A. Jafari, S. Khademi, M. Farahmandjou, A. Darudi, R. Rasuli,
Volume 38, Issue 2 (9-2019)
Abstract
Titanium dioxide nanoparticles (TiO2) are known as a widely used photocatalyst. In order to improve the performance of these nanoparticles, the recombination of the electron-cavity pair must be reduced and the absorption rate of the visible region should be expanded. One way to increase the performance of these nanoparticles is using cerium doped TiO2. In the present study, pure and doped titanium dioxide nanoparticles were made by the electrical discharge method. The effect of cerium dopants on the structural, morphological and optical properties were studied by x-ray diffraction (XRD), scanning electron microscopy (FESEM), diffused reflection spectroscopy (DRS), photoluminescence (PL) and infrared fourier transform (FTIR) spectroscopy analyses. XRD analysis revealed that the size of TiO2 nanocrystals was decreased to 7.7 nm. The FESEM morphology of the samples also showed that the uniformity of the Ce doped TiO2 was decreased. Further, the DRS results indicated that the band gap energy of Ce-TiO2 was decreased to 2.24 eV. The photoluminescence results demonstrated that the intensity of PL was reduced for the Ce-TiO2 sample, which reduced the recombination of the electron-hole coupling and increased the photocatalytic activity in the doped sample.
