Showing 8 results for Precipitation
A. Samadi, A. Abdollah-Zadeh, S.h. Razavi , H. Assadi,
Volume 29, Issue 1 (6-2010)
Abstract
The initial stages of the precipitation in a dilute Ni-Al binary alloy, Ni-11.6 at.%Al, were studied using differential
scanning calorimetry (DSC), X-ray diffraction (XRD), electron diffraction and electron microscopy (FEG-SEM and TEM) techniques. Three samples were similarly solution treated and then cooled to room temperature under different cooling rates, 170، 25 and 0.03oCs-1. The results indicate a clearly homogenous nucleation during rapid quenching which takes place via simultaneous ordering and phase separation. However, by decreasing the cooling rate to 25oCs-1 the nucleation mechanism changes to heterogeneous on the preferred nucleation sites. The capability of the mentioned empirical techniques for studying the initial stages of the γ′ is another subject which is studied in this article.
M. Khajelakzay, R. Shoja Razavi, S.m. Barekat,
Volume 34, Issue 3 (12-2015)
Abstract
Precipitation has always been one of the important methods in the preparation of ceramic nanopowders. In this study, the most important parameters, ageing time and concentration parameters, have been studied. Yttrium oxide (Yttria) nanopowder was synthesized by precipitation method. Yttria micropowder and ammonium hydrogen carbonate were used as precursor materials. The study involved aging time and concentration in four and three levels, repectively (3, 6, 12 and 24h for ageing time and 0.25, 0.5 and 0.75 mol/L for concentration). Synthesized phases, thermal behavior and particle size were studied by X-ray diffraction pattern (XRD), thermogravimetry (TG), differential thermal analysis (DTA) and field emission scanning electron microscopy (FE-SEM). Fourier transform infrared spectroscopy analysis (FTIR) was used for studying bonding before and after the heat treatment at 900, 1000 and 1100 °C.
G. Gordani, A. Ghasemi, A. Saidi,
Volume 34, Issue 4 (3-2016)
Abstract
Nanoparticles of Mg–Co–Ti substituted strontium hexaferrite with nominal composition of SrFe12-2x(Mg,Co)0.5x TixO19 (x=0-2.5) were synthesized by a co-precipitation method. The structural, magnetic and electromagnetic properties of samples were studied as a function of x by thermal gravimetric (TG), X-ray diffraction (XRD), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM) and vector network analysis. It was found that the synthesis temperature increases with an increase in Mg–Co–Ti substitution and hence the particle size decreases. The XRD results showed that whole samples had good crystallinity and with an increase incations, the impurity phase of Fe2O3 appears. The results of hysteresis loops indicated that the saturation of magnetization of ferrite decreases from 40 emu/g to 19 emu/g with an increase in x. The Mössbauer spectroscopy showed that the cations are substituted in the 12k site of magnetoplumbite structure. Vector network measurements showed that the doped samples had much more effective reflection loss values than those of undoped ferrites. As a result, Mg–Co–Ti doped Sr-hexaferrites with x=2 can be proposed as suitable absorbers for applications in microwave technology with a good deal of consistency.
S.t. Mohammadi Benehi, S. Manouchehri, M.h. Yousefi,
Volume 35, Issue 3 (12-2016)
Abstract
Magnesium-manganese ferrite nanopowders (MgxMn1-xFe2O4, x=0.0 up to 1 with step 0.2) were prepared by coprecipitation method. The as-prepared samples were pressed with hydrolic press to form a pellet and were sintered in 900, 1050 and 1250˚C. Scanning Tunneling Microscope (STM) images showed the particle size of powders about 17 nm. The X-ray patterns confirmed the formation of cubic single phase spinel structure in samples sintered at 1250˚C. Substituting Mg2+ with Mn2+ in these samples, the lattice parameter decreased from 8.49 to 8.35Å and magnetization saturation decreased from 74.7 to 21.2emu/g. Also, coercity (HC ) increased from 5 to 23Oe and Curie temperature (TC ) increased from 269 to 392˚C. Samples with x= 0.2, 0.4, 0.6 sintered at 1250 ˚C, because of their magnetic properties, can be recommended for hyperthermia applications and for phase shifters.
Mr S. A. Razavi, Mr S. F. Ashrafizadeh,
Volume 36, Issue 2 (9-2017)
Abstract
Age hardening processes cause a wide range of changes in 17-4 PH stainless steel properties. Aging at 480ºC for 1 hour (A480-1) and aging at 620ºC for 4 hours (A620-4) are two most applicable heat treatment processes for this alloy. Not only the studies on fatigue behavior of this alloy in these two heat treatment conditions are few, but also the methods of fatigue test were mostly axial. In this study, after microstructure studies, hardness and tension tests, fatigue behavior at A480-1 and A620-4 conditions were evaluated by using a rotational bending fatigue test machine. Tension results showed that yield strength and ultimate tensile strength of A480-1 specimens were 40 percent more than A620-4 specimens. However, elongation of A620-4 specimens was 30 percent more than A480-1 specimens. Fatigue results revealed the endurance limit of aged specimens is 50 MPa more than overaged specimens. Overall results showed that A480-1 condition specimens are more resistant to fatigue than A620-4 condition specimens.
M. Ghasemian Malakshah, F. Ashrafizadeh, A. Eslami, F. Fadaeifard,
Volume 38, Issue 2 (9-2019)
Abstract
Since martensitic precipitation hardened 17-4pH stainless steel has been widely used in corrosive environments, evaluation of its corrosion fatigue behavior is important. In this research, after microstructural studies, mechanical, corrosion, fatigue and corrosion fatigue tests were performed on 17-4pH specimens. Fatigue and corrosion fatigue tests were carried out at the stress ratio of -1 and the stress frequency of 0.42 Hz (to increase the effect of corrosive solution), and corrosion fatigue tests were conducted in 3.5% NaCl solution, an environment similar to corrosive sea water. Fatigue limit of 17-4pH stainless steel was 700 MPa in air and 415 MPa in corrosive environment. Comparing the S-N curves of this alloy at the optimal heat treatment cycle in two modes of fatigue and corrosion fatigue revealed the reduction of fatigue limit up to 40 % in the presence of corrosive environment. This reduction was due to the effect of observed corrosion pits on the surface and Damaged passive layer.
H. R. Karimi, H. Mansouri, M. R. Loghman Estarki, M. Tavoosi , H. Jamali,
Volume 40, Issue 1 (5-2021)
Abstract
This study aimed to compare the phase changes and morphology of yttria-stabilized zirconium oxide powders (YSZ) synthesized by co-precipitation and molten salt methods. Ammonia precipitating agent was used for the synthesis of YSZ powder by co-precipitation method and a mixture of sodium carbonate and potassium carbonate salts was used as a molten salt in the molten salt method. Samples were characterized by X-Ray Diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Fourier Transform Infrared Spectroscopy (FTIR), Thermal Gravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC) analysis. The results showed that only the sample prepared with zirconium oxychloride and yttrium nitrate by co-precipitation method had a single phase of yttria-stabilized zirconium oxide with tetragonal crystal lattice and particle size distribution in the range of 30 to 55 nm. The powder synthesized by the molten salt method contained a mixture of zirconia with monoclinic crystal lattice and yttria stabilized zirconia with tetragonal crystal lattice and particle size of 200 nm.
Sh. Talebniya, M. R. Saeri, I. Sharifi, A. Doostmohammadi,
Volume 41, Issue 1 (8-2022)
Abstract
Magnetic nanoparticles are of interest in various research fields such as magnetic fluids, catalysts, biotechnology, medicine, information storage, and environmental issues. However, spinel ferrite magnetic nanoparticles with proper magnetic properties could not be used alone in these applications because of their lack of biocompatibility and instability in aqueous solutions. Surface coating is an effective strategy to eliminate or minimize this issue. In this study, FeFe2O4 and ZnFe2O4 spinel ferrites were synthesized using the reverse co-precipitation method under a nitrogen gas atmosphere. The magnetic behavior of the particles, determined by a vibrating magnetometer (VSM) showed the saturation magnet (Ms) values of the FeFe2O4 and ZnFe2O4 spinel. Fourier-transform infrared (FTIR) spectra showed two high-frequency bands v1 and v2 at about 554-578 and 368-397 cm-1, respectively, which were related to the spinel structure. Finally, the synthesized FeFe2O4 nanoparticles were coated with chitosan and polyethylene glycol (PEG) biopolymers. The TEM and FTIR analysis indicated that the magnetic nanoparticles were uniformly coated by the biopolymers.
