Showing 14 results for Silicon
M. Kalantar and G. Fantozzi,
Volume 22, Issue 1 (7-2003)
Abstract
Dense Silicon nitride was investigated to determine the effect of its microstructural parameters and densification on thermo-mechanical properties and thermal stress resistance to fracture initiation during a hot or cold mechanical and thermal shock testing. The different materials and microstructures were obtained by changing the parameters such as the type of the powder, additive, forming process and sintering condition. Maximum crack growth and thermal shock resistance of dense Si3N4 are achieved after complete conversion of the aàB transformation, and after the change in grain morphology towards elongated
grain and the relative crystallization of the second phases have been obtained. The characteristics are obtained by a high a phase content of the starting powder, high Y2O3, and sintering condition of higher temperature (2000ْC), longer soaking times (1h) and load application at the beginning of the thermal cycle.
Keywords: Silicon nitride, Thermo- mechanical properties, Thermal shock resistance, Crack propagation resistance
A.r. Kiani Rashid and M. A. Golozar,
Volume 22, Issue 2 (1-2004)
Abstract
M. Babashahi, M.h.enayati, M. Salehi, A. Monshi,
Volume 29, Issue 1 (6-2010)
Abstract
In the present study phase transformation of silicon and silica during milling in different atmospheres was investigated. The silicon powder was subjected to high energy ball milling in ammonia (25%) atmosphere. The milled powder was subsequently annealed at 1200 ◦C for 1 hour. In another test a mixture of AlN and amorphous silica (micro silica) was subjected to high energy ball milling. The milled powder mixture was subsequently annealed at 1200 ◦C for 2 hours. Phase analysis of the as milled and annealed powders was performed by X-ray diffractometery (XRD). Powder morphology was also examined using a scanning electron microscope (SEM). Results showed that ball milling of silicon in ammonia formed an amorphous phase which transformed to quartz on further milling. After annealing quartz, cristobalite and another oxide phase called O phases were developed on XRD patterns. Ball milling of AlN and amorphous silica led to the transformation of amorphous silica to stishovite phase. This process was completed after annealing..
R. Esmaeili, M.r. Dashtbayazi,
Volume 32, Issue 2 (12-2013)
Abstract
In the present work, molecular dynamics simulation method was used for determining Young's modulus, Shear modulus and Poisson’s ratio of Al-SiC nanocomposites, with different volume fractions of the reinforcements. For simulation, the open source package, LAMMPS, was used. After putting Aluminum and Silicon Carbide atoms in their initial positions, interatomic potentials between them were defined. EAM potential was used for Aluminum atoms, Morse potential was used for Al-C and Al-Si, and for C-C, Si-C, and Si-Si Tersoff potential was used. According to the elastic bounding principal, and the comparison between the simulations results and Voigt, Ruess and Halpin-Tsai micromechanical models showed that the results were close to the upper bound Voigt model.
Zahra Omidi, Saeed Reza Bakhshi, Ali Ghasemi,
Volume 33, Issue 3 (3-2015)
Abstract
Silicon nitride has attracted a considerable attention because of its excellent properties such as high-temperature strength, good oxidation resistance, high corrosion resistance, good thermal shock resistance, high creep resistance and good thermal and chemical stability. There are several different fabrication methods for synthesizing Si3N4 particles. Such methods are mostly costly and kinetically slow and require lengthy heat treatment. In this study, Si3N4 compounds were synthesized by means
of mechanical milling. In the mechanical milling route,Si powder (≤99.0%) was milled under nitrogen gas for 25 h and heated at various temperatures 1100-1200-1300 and 1400 C for 1 h at the nitrogen atmosphere at a rate of 200 ml/min. Silicon powder was also annealed under a similar condition in order to evaluate the impact of milling process on the low temperature synthesizing of Si3N4. Phase identification and microstructural characteristics of products were evaluated by X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy. The Fourier transform infrared spectroscopy and thermal analysis were used for characterization of the formed bands and thermal treatment of the sample, respectively. The obtained results exhibited that Si3N4 powder was fully formed with two kinds of morphologies including globular particles and wire with a width of 100–300 nm and length of several microns at sintering temperature of 1300 C. This was confirmed by the Si–N absorption bonds in the FTIR trace. Based on XRD results, 25 h milling reduced temperature of reaction remarkably in comparison with direct nitridation of Si powders for 1 h. With an increase in the reaction temperature, the Si3N4 samples had a phase transformation 𝛂→𝛃, and variation of the morphology followed the vapor–liquid -solid mechanism.
N. Zakeri, S. Otroj, M.r. Saeri,
Volume 34, Issue 3 (12-2015)
Abstract
In this study, the effect of nano-titania addition on the mechanical strength of mullite-bonded alumina-siliconcarbide nano-composites was investigated. To this end, the gel-casting process via nano-silica sol was used for shaping the nano-composite.The firing temperature of composition was determined by use of STA. The compressive and bending strengths of samples were measured after firing at 1300 °C. Besides, the physical properties, phase composition and microstructure of the composites were evaluated after firing. The results showed that the use of nano-titania up to 1 wt.% had a higher effect on improvement of nano-composite mechanical strength. The nano-titania addition led to increasing of mullite phase and higher growth of its needle-like grains. Enhancing of ceramic bonds between grains and the improvement of mechanical strength were obtained by increasing the mullite phase.
M. Khajelakzay, S. R. Bakhshi, G.h. Borhani,
Volume 34, Issue 4 (3-2016)
Abstract
In this study, synthesis of silicon nitride by mechanical alloying and the effects of important parameters of milling time and heat treatment temperature, time and rate are presented. Silicon micro powder and nitrogen gas were used as precursor materials. Synthesized phases, morphology and particle size were investigated by X-ray diffraction pattern (XRD) and Field emission scanning electron microscopy (FE-SEM), respectively. X-ray fluorescence analysis (XRF) was used for silicon nitride purity investigation.The optimum sample was produced at 30 h milling time, heat treatment at 1300 ℃ and 22 ℃/min heating rate conditions. X-ray fluorescence analysis showed more than 98% purity.
M. Haghshenas Gorgani, M. Mirkazemi, F. Golestanifard,
Volume 37, Issue 4 (3-2019)
Abstract
In this research, the rheological behavior and stability of suspensions containing Si3N4, Al2O3, Y2O3 and starch were investigated in order to use them in the starch consolidation casting of porous silicon nitride. Dolapix CE64 was used as the dispersant. Then, the effect of some parameters such as Si3N4 surface oxidation, dispersant content, solid loading and starch content on the viscosity and rheological behavior of Si3N4-starch slurry was determined. Surface oxidation of Si3N4 powder at 800°C for 2 hours reduced the viscosity of the slurry, effectively. The best dispersant content was 0.4 wt. %, relative to ceramic powders. Slurries containing 30 to 40 vol. % and 7.5 to 25 vol. % starch, relative to total solid loading, had the suitable viscosity and the sufficient stability for casting by the starch consolidation method.
M. Lashani Zand, B. Niroumand, A. Maleki,
Volume 37, Issue 4 (3-2019)
Abstract
Mechanical properties of the alloys are a strong function of the average silicon particles size and the secondary dendrite arm spacing (SDAS). Modified Hall-Petch equation expresses the effects of these two microstructural parameters on the yield strength and ultimate tensile strength of the Al-Si based alloys. These microstructural parameters depen on parameters such as chemical composition, cooling rate and melt treatment. In this study, the effect of cooling rate on the equation constants of the alloy were determined. For this purpose, the alloy was poured at 750 °C in three different molds including a sand mold, a preheated steel mold, and a water cooled steel mold. The Thermal and microstructural analysis showed that the cooling rate in the metal mold was 15.7 times higher than that of the sand mold, which resulted in a decrease of the SDAS from 54 micrometers to 17 micrometers. It was also found that by reducing the SDAS from 45 micrometers to 17 micrometers, the yield strength and tensile strength were increased by 16.5% and 6.5%, respectively. The modified Hall-Petch equation constants and the microstructure-mechanical properties relationships were then established by the microstructural and tensile test studies.
A. R. Parvanian, H. R. Salimijazi, M. H. Fathi,
Volume 38, Issue 4 (1-2020)
Abstract
The concentrated solar power (CSP) is one of the renewable energy sources in which solar irradiation heat energy will be used in a steam turbine to generate electrical grid. Solar radiation is absorbed by a solar receiver reactor on the surface of a porous solar absorber. In this survey, synthesis and mechanical/thermal characterization of micro-porous silicon carbide (SiC) absorber to be used in solar reactor is carried out. SiC foams were synthesized and categorized based on three different pore sizes i.e. 5, 12 and 75 ppi. Mechanical behavior and thermal shock resistance of porous foams in the working temperature range for absorber (25-1200 °C) were evaluated. Results revealed that the specific compressive strength (σc/ρ) of foams increase exponentially by a decrement in the porosity percentage and the average pore size. Moreover, for foams with smaller pore size, a considerable decrease in mechanical strength due to thermal shock was observed. This could be due to increase in the number of struts per unit volume i.e. more weak struts to withstand the mechanical loading. So, porous foams with coarser pore sizes were distinguished to be more capable of tolerating thermal shock while serving as solar absorbers.
M. Zarchi, Sh. Ahangarani ,
Volume 39, Issue 1 (5-2020)
Abstract
The structural and optical properties of polycrystalline silicon films obtained on a silicon wafer by electron beam physical vapor deposition (EBPVD), were studied in this paper. These films were initially amorphous and changed to a crystalline solid phase during annealing. Annealing was performed in an inert gas atmosphere tube furnace at different temperatures. Micro-structure of the films was analyzed to know the relationship between the crystalline / amorphous composition, grain size and characteristics of the films. The results showed a decrease in roughness with increasing annealing temperature and structural density. Moreover, results of Micro-Raman spectrum showed formation and increase of silicon nanocrystals in the annealed condition when the thickness of the coating increased due to structural defects.
M. Mahallati, M. Khosravi,
Volume 39, Issue 2 (8-2020)
Abstract
In this research, using phenolic resin as the precursor of carbon and various amounts of ethylene glycol as a pore former, porous samples of hard carbon were synthesized. Samples were characterized by x-ray diffraction (XRD) and N2 adsorption-desorption methods. Broad diffraction peaks represent the amorphous structure of samples. Moreover, the gas adsorption-desorption curves showed that the adsorption isotherms of samples were of type IV and all samples had meso-micro porous structure. Charge-discharge tests were performed on samples to obtain their capacities. The sample with higher capacity, broader XRD pattern and appropriate porosity, was selected for silicon incorporation. Silicon nanoparticles were obtained by mechanical milling of its micro particles. According to XRD patterns, silicon nanoparticles had a crystalline structure. Field emission scanning electron microscopy (FESEM) images approved uniform distribution of nanoparticles. XRD patterns of nanocomposites evidenced the existence of hard carbon and silicon. The electrochemical test results showed that the capacity, coulombic efficiency and cycle life of nanocomposites were improved by increasing the amount of silicon.
A. Zolriasatein, S. Navazani, M. Rezaei Abdadchi, N. Riahi Noori ,
Volume 39, Issue 3 (12-2020)
Abstract
In this paper, the effect of adding aluminum trihydrate (ATH) on electrical (including dielectric constant, dielectric loss and strength, volume and surface resistivity) and hydrophobic properties of two-part room temperature volcanized (RTV) silicone rubber resin coatings were investigated. For this purpose, the RTV-ATH nanocomposite was made by physical mixing and its electrical and hydrophobic properties were compared with those of pure RTV. The results showed an increase in the dielectric constant (from 3.11 to 4.13), the dielectric loss (by ~ 0.06) and the dielectric strength (by ~ 4 KV/mm) of the RTV-ATH composite compared to the pure RTV. Moreover, ATH increased volume resistivity and reduced the surface resistivity of composite coatings. On the other hand, by spraying of coatings, no improvement in the hydrophobicity class of composite coating compared to pure RTV was observed and both samples were standardized in the HC2 standard class. Structural analysis of samples was performed by X-ray diffraction, optical microscopy and scanning electron microscopy and the presence of the main phases in them was confirmed.
H. Fallah-Arani, N. Riahi-Noori, S. Baghshahi, A. Sedghi, F. Shahbaz Tehrani,
Volume 40, Issue 4 (3-2022)
Abstract
In this research, the effect of addition of silicon carbide (SiC) nanoparticles on the improvement of the structural, superconductivity, magnetic, and flux pinning properties of high-temperature superconductor Bi1.6Pb0.4Sr2Ca2Cu3O10+θ (Bi-2223) was investigated. The Bi-2223 ceramic superconductor was prepared using the sol-gel method, and silicon carbide nanoparticles were modified by Azobisisobutyronitrile (AIBN). The X-ray diffractometry, feild emission scanning electron microscopy, magnetic susceptibility, and hystersis loop measurements were performed to characterize the synthesized compounds. Based on the magnetic measurements, the superconductivity transition temperature dropped with an increase in the content of nanoparticles. Also, the maximum magnetization, hysteresis loop width, critical current density, and magnetic flux pinning force belonged to the sample with 0.4 wt.% SiC nanoparticles.
