Showing 11 results for Zinc
A. Saatchi, H. Yan, and S. J. Harris,
Volume 20, Issue 1 (7-2001)
Abstract
Zinc was electrodeposited from an acidic sulphate solution on commercial steel sheet substrates galvanostatically at 10, 20, and 100 mA/cm2. The steel substrates had an average roughness number of 1.34 microns and a high percentage of its grains had their (111) planes parallel to the plate surface. During electrodeposition at 10 mA/cm2, on some specimens, there was an intense potential fluctuation around –870 mV vs Saturated Calomel Electrode (SCE). During this period zinc hydroxide precipitated on the surface. After a certain time, the potential dropped to –1020 for zinc deposition. Zinc nuclei were seen to precipitate from zinc hydroxide. Increasing current density changed nucleation mode from progressive to instantaneous, and also changed the size, morphology, and texture of zinc deposits.
Keywords: Zinc Electroplating, Current Density, Morphology, Orientation
K. Raeissi, A. Saatchi and M. A. Golozar,
Volume 23, Issue 2 (1-2005)
Abstract
On electropolished steel at low current densities, morphology and texture of electrodeposited zinc were investigated. Zinc coating is consisted of hexagonal crystallites laid on each other to produce packets. These packets are of different sizes and are stacked in different orientations to construct a homogeneous coating on steel substrate. This coating does not have texture, i.e., it has a random texture. With increasing current density, the morphology changes completely as each grain attains a special orientation. In this case, coating has a strong basal plane (0002) along with low angle planes (1013 and 1014). Coating obtained on mechanically polished surfaces consists of individual packets of zinc crystals, which are near each other with different
orientations. These coatings have a higher density of basal plane (0002) in comparison to electropolished surfaces. The morphology and texture variations with cathodic polarization and surface preparation of steel are due to their effect on nucleation and growth.
A. Nasr-Esfahany and M.heydarzadeh Sohi,
Volume 23, Issue 2 (1-2005)
Abstract
Zinc-Nickel electrodeposits have been widely adopted for surface treatment of automobile steel sheet for high corrosion resistance. In this work the effect of pulse parameters on the Zn-Ni alloy electrodeposits was investigated. The hardness, thickness, corrosion resistance and composition of deposits thus produced were investigated. The surface topography of the deposits was also observed in SEM and results are reported. It has been shown that the thickness of the pulse electrodeposits
was almost even. The hardness in the pulse electrodeposits increased by increasing the on-time period and by decreasing the current density. It was also noticed that increasing the on-time period increases the nickel content of the deposit. Pulse electrodposits had fine structure and the structure become finer by reducung the on-time period and pulse frequency. The corrosion dehaviors of the deposits were then investigated. The results showed that the corrosion resistance of the DC electrodeposits improves in their nickel content increases. Pulse electodeposits show the same behavior, but deposits with about 13% nickel show maximum corrosion resistance.
M. Ashuri, F. Moztarzadeh, N. Nezafati, A. Ansari Hamedani, M. R. Tahriri,
Volume 31, Issue 1 (6-2012)
Abstract
In the present study, a bioceramic-based composite with remarkable mechanical properties and in vitro apatite forming ability was synthesized by sintering compacts made up of mixtures of hydroxyapatite (HA) and sol-gel derived bioactive glass (64SiO2-26CaO-5MgO-5ZnO) (based on mole %). HA was synthesized through co-precipitation method. The stabilization temperature of the bioactive glass was set to be 700 ºC according to simultaneous thermal analysis (STA). Laser Particle Size Analysis (LPSA) was used to compare the particle size distributions of the synthetic powders. HA matrix was mixed with different weight percentages of bioactive glass (5, 10, 15, 20, 25 and 30 wt. %) and compressed by 80 MPa pressure. After sintering the uniaxial compression test of the samples was done and the specimen with the highest compressive strength (20 wt. % bioactive glass) was selected to be immersed in the Simulated Body Fluid (SBF) for 3, 7 and 14 days. The results showed that the compressive strength of the sample decreased after keeping it in the SBF. Also, inductively coupled plasma analysis (ICP) was used to study the ion release behavior of the sample in the SBF. Finally, phase composition, microstructure and functional groups in the composite were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infra-red spectroscopy (FTIR) techniques, respectively.
S. Yazdkhasti, A. Monshi, A. Doostmohammadi,
Volume 34, Issue 4 (3-2016)
Abstract
With various features such as strong oxidation, biocompatibility and acceptable mechanical properties, titanium dioxide (TiO2) is among the materials that are frequently used in biological and medical applications. Nowadays, with the aim of increasing the efficiency of titanium dioxide and practical use of this material, doping it with elements such as silver, zinc and iron has been favored. In this study, Ag-TiO2 and ZnO-TiO2 nanoparticles were prepared by the sol–gel method and were evaluated and compared.In order to identify the present phases in the structure, X-ray diffraction analysis was used. Also for the characterization of the nanoparticles, Ultraviolet–visible spectroscopy (UV-Vis), Energy-dispersive X-ray spectroscopy (EDS), Field Emission Scanning Electron Microscope (FESEM) and Zeta Potential were used. Inaddition, the antibacterial activities of nanoparticles were investigated and compared. The results showed that sol-gel method could successfully produce nanoparticles of Ag-TiO2 and ZnO-TiO2 with the expected combination. The investigation of antibacterial properties of these particles revealed that at lower inhibitory concentrations, Ag-TiO2 composition has a higher antibacterial activity than ZnO-TiO2 one.
M. Mousapour, M. Azadbeh, A. Mohammadzadeh,
Volume 35, Issue 3 (12-2016)
Abstract
In this paper, the possibility of elephant foot phenomenon in sintered alloys with volatile components has been studied. To do this, Cu-28Zn brass samples were sintered at the range of 890-970°C for 20 min. The in situ images from brass samples were taken at various sintering conditions. It is concluded that although liquid is pulled down by gravity, but elephant phenomenon was not appeared in these compacts. Instead, the samples were swelled. Chemical composition change and pores coarsening due to zinc evaporation could be considered as the main cause of swelling in brass compacts.
A. Vahedi, H. Nadimi, D. Haghshenas Fatmesari, S. Firoozi,
Volume 37, Issue 3 (12-2018)
Abstract
The aim of this study was to investigate the effect of tartrate ion (C4H4O62-) on the extraction and separation of zinc and cadmium using D2EHPA extractant. The presence of tartrate ion in the solution caused the shift of the extraction curve of zinc and cadmium to the more alkaline pH; however, the shifting rate for the cadmium extraction curve was more significant. In the absence of tartrate ion, ΔpH50% value was equal to 0.65. If 0.2 M tartrate ion were added to the aqueous phase, ΔpH50% value would increase to 1.09. The FT-IR analysis of organic phase showed that tartrate ion absorbed the organic phase along with zinc and cadmium. "Slope analysis method" also showed that 0.25 M and 0.5 M tartrate ion participated in the zinc-tartrate and cadmium-tartrate complex formation, respectively; however, extraction number was changed with increasing the tartrate ion concentration.
T. Rajabi, M. Vahedi, S. K. Sadrnezhaad,
Volume 39, Issue 2 (8-2020)
Abstract
Zinc/zinc oxide nanoparticles are used in an increasing number of medical and industrial applications due to their attractive physical, chemical and antibacterial properties. Therefore, achieving a simple and beneficial way to produce them is an important aspect. In this study, zinc/zinc oxide nanopowders were synthesized by fast electric discharges between two electrodes of (a) a spark device in distilled water medium and (b) a handmade high-voltage ignition machine in argon gas medium. The resulting powders were characterized by x-ray diffraction (XRD), dynamic light scattering (DLS) and field emission electron microscopy (FESEM). Using the spark device in distilled water, a mixture of zinc crystals with an average diameter of 11.28 nm and zinc oxide crystals with an average diameter of 22.22 nm was produced. However, using the handmade device in argon, zinc crystals with an average diameter of 7.5 nm were obtained and subsequently oxidized due to their extremely high activity. The production rate of the high voltage discharge method was lower than other conventional methods. On the other hand, its ability in reducing the size and increasing the particle activity was higher than other methods.
A. Zamani, M. R. Loghman Estraki, S. R. Hosseini, M. Ramezani, A. Al-Haji,
Volume 39, Issue 3 (12-2020)
Abstract
The aim of the study was to investigate the effect of temperature, time, pH, capping agent concentration (mercaptoacetic acid), Zn to Se and Se to reducing agent (NaBH4) mole ratios on morphology, phase developments and size of zinc selenide nanoparticles prepared by hydrothermal method. Characterization of zinc selenide nanoparticles was performed by Field Emission Electron Microscopy (FESEM), Energy Dispersive X-ray Spectrometry (EDS), X-ray Diffraction (XRD), Induced Coupled Plasma Spectrometry (ICP), Fourier Transform Infrared spectroscopy (FTIR) and Simultaneous Thermal Analysis (STA). The results of EDS showed that the ratio of atomic percentage of Zn to Se in the optimized zinc selenide nanoparticles is 1: 1 and elements are evenly distributed in the nanoparticles. Based on the results of FTIR and STA thermal analyses, MAA as the stabilizing agent binds to and stabilizes zinc selenide nanoparticles. Finally, fine nanoparticles of zinc selenide with narrow size distribution, spherical shape and cubic crystal structure were obtained at the minimum temperature (130 °C) and processing time (15 hours) with the least amount of reducing and capping agents compared to previous researches.
F. Rafati, N. Johari, F. Zohari,
Volume 40, Issue 4 (3-2022)
Abstract
In the present study, PCL/ZnO nanocomposite scaffolds containing 0, 5, and 15 wt.% of ZnO nanoparticles were prepared via the salt leaching/solvent casting method. The influence of ZnO nanoparticles on the morphology of prepared PCL/ZnO scaffolds was investigated using SEM images. The compressive strength test evaluated the effect of scaffolds’ morphology on mechanical properties. The XRD technique confirmed the desired phases in the scaffold composition. The results showed that the compressive strength and structural integrity of the scaffolds increased by increasing ZnO nanoparticles content as the reinforcement. However, the compressive strength and structural integrity decreased by increasing the amount of ZnO nanoparticles up to more than 5 wt.%. In summary, PCL/ZnO nanocomposite scaffold containing 5 wt.% of ZnO nanoparticles revealed the highest strength, compressive modulus, and structural integrity.
F. Dehghani Firoozabadi, A. Ramazani Saadatabadi, A. Asefnejad,
Volume 41, Issue 1 (8-2022)
Abstract
Today, many people need to use bone grafts and implants because of damage to bone tissue. Due to the stimulation of the immune system after implantation, infection at the operation site is very common, which causes swelling and pain in the operation area. The use of zinc oxide nanoparticles reduces infection at the operation site and reduces the patient's need for antibiotics. In the present study, the morphology of the scaffolds was investigated by field emission scanning electron microscope (FE-SEM). The toxicity of the samples was evaluated using MTT assay. The behavior of nanocomposites against Escherichia coli and Staphylococcus aureus was investigated by measuring the diameter of the growth inhibition zone. It was found that modification of scaffolds with nanoparticles caused a growth inhibition in bacterial culture medium. It was also observed that fibroblast cells on the surface of the modified scaffolds had longer survival than polymer scaffolds. This study showed that the addition of oxidizing nanoparticles improves the antibacterial properties of scaffolds and cell viability and reduces scaffold toxicity.
