M.r. Borhani, S.r Shoja-Razavi, M. Erfanmanesh, F. Kermani, S.m. Barekat ,
Volume 9, Issue 1 (5-2023)
Abstract
Inconel 713LC super alloy is one of the most widely used high-temperature alloys. Due to the high level of gamma prime phase caused by Ti and Al alloy more than a critical value, this alloy is considered as one of the non-weldable alloys. One of the basic repair methods of this series of superalloys is laser cladding methods. In this research, the IN713LC substrate was reconstructed with Inconel 625 powder by a direct laser deposition system. To characterize, optical and electron microscopy tests, porosity measurement, and XRD were carried out; The results showed that the R (growth rate of the dendrite tip) increases at high speeds of laser cladding; as a result, the G/R (combined solidification point) ratio decreases, and the structure tends towards the coaxial dendritic direction. For this reason, by increasing the speed of laser scanning from 4 to 6 mm/s, the coaxial dendritic structure increases. The hardness measurement results indicate a decrease in the hardness up to the junction area from 430 to 370 Vickers and fluctuations of about 50 Vickers. Due to the high solidification speed, the average distance between the secondary dendritic arm space was 0.8 at the bottom, 1.01 in the middle, and 1.75 micrometers at the top of the sample. Due to the high cooling speed, only carbides and lava phases are formed. Also, the porosity measurement results of the cladding indicate a maximum porosity of 0.1 percent.
M. R. Borhani, M. Rajabi, R. Shoja Razavi, R. Jamaati,
Volume 9, Issue 2 (1-2024)
Abstract
Reconstruction of parts using direct laser deposition can create a combination of high wear resistance properties, good toughness, and corrosion resistance. In this research, the wear properties of Inconel 625 powder cladding on the same substrate have been investigated; For this purpose, room temperature and high temperature wear tests have been used. Mass reduction, friction coefficient, width and depth of wear penetration have been measured. Also, a scanning electron microscope with an energy disspersive spectroscopy system was used to evaluate the cladding surface. The results showed that the mass reduction due to wear at Inconel 625 cladding compared to Inconel 625 substrate has decreased by 7% and 52%, respectively, at temperatures of 25°C and 620°C. Also, the wear mechanism of the room temperature of the cladding is mainly scratchy, and the wear mechanism of high temperature is mainly sticky.
Morteza Ilanlou, Reza Shoja Razavi, Pouya Pirali, Mohhamadreza Borhani,
Volume 9, Issue 2 (8-2025)
Abstract
In this study, laser direct deposition was employed to fabricate a functionally graded transition between 17‑4PH stainless steel and Stellite 6. Specimens were designed and produced such that the chemical composition varied incrementally from 100 % 17‑4PH to 100 % Stellite 6, with each step involving a 25 % decrease in the 17‑4PH content and a corresponding 25 % increase in Stellite 6. Microstructural evolution and elemental distribution were characterized by scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS), while mechanical properties were assessed via Vickers microhardness testing and uniaxial tensile tests. The microstructural analysis revealed a needle‑like martensitic matrix in the substrate, which transformed into cellular dendrites upon reaching the 25 % Stellite 6 layer. As the Stellite 6 fraction increased, along with corresponding rises in Cr and W content, grain boundaries broadened and carbides accumulated within interdendritic regions. At the 50 % composition, oriented columnar dendrites became prominent, and at higher Stellite 6 levels the dendritic structure refined further, ultimately evolving into an equiaxed morphology. Microhardness measurements showed a continuous increase from approximately 300 HV in the 17‑4PH substrate to 490 HV in the pure Stellite 6 layer. Tensile testing demonstrated that both yield strength (σᵧ) and ultimate tensile strength (σᵤ) remained within 1102–1159 MPa across all compositions, with no evidence of brittle phases or manufacturing defects. Elongation increased from 7 % in pure Stellite 6 to 19 % in pure 17‑4PH, with the 50 %–50 % gradient exhibiting an optimal balance of strength and ductility (14.5 % elongation).
