Showing 3 results for Natural
B. Ghasemi,
Volume 21, Issue 1 (7-2002)
Abstract
In this paper, mixed forced and natural convection heat transfer in a rectangular cavity has been numerically studied. the cavity receives a uniform heat flux from one side and is ventilated with a uniform external flow. The external flow enters the cavity from the heated side and leaves the cavity from the opposite side. The velocity and temperature fields and heat transfer rate are determined by solving the two-dimensional continuity, momentum and energy equations. In this research, steady-state flow with constant Reynolds number, Re=100, is considered. Rayleigh number is in the range of 0≤Ra≤107. First, the results are presented for a cavity with constant aspect ratio, AR=2, and four different inlet and exit opening positions. Then cases with a fixed opening position and different aspect ratios including 0.1, 0.25, 1, 4 and 10 are modeled. In the cavities with opening in the bottom or cavities with aspect ratios less than one, the results show weak effects of natural convection on heat transfer. This research has been done for air as a working fluid (Pr=0.71). In some cases, the results are compared with those from previous studies.
Keywords: Convection, Natural, Forced, Cavity, Rayleigh, Ventilate
H. Ahmadikia, and G. A. Iravani,
Volume 26, Issue 1 (7-2007)
Abstract
Design of a natural dry cooling tower has been accomplished in two sections: the design of heat exchangers and the numerical solution of flow through the tower. Heat exchanger (Heller type) has been simulated thermodynamically and then coupled with a computer program, which calculated the turbulent natural convection flow through the tower. The computer program developed for this purpose can be used to obtain thermodynamic propertied of the cooling tower such as mass flow rate of air, temperature of outlet water, distribution of temperature, distribution of velocity, and distribution of pressure through the tower. Numerical results have been compared with experimental data of Shahid Montazery Thermal Power Plant under different environmental conditions. Comparison between numerical results and experimental data showed good agreement.
M. Nemati, M. Sefid, M. S. Barghi Jahromi, R. Jahangiri,
Volume 40, Issue 2 (1-2022)
Abstract
In the present work, the effect of magnetic field, changes in the angle of inclination of the cavity and the shape of nanoparticles on the flow field and heat transfer of water-alumina with uniform heat generation/absorption is investigated by Lattice Boltzmann method (LBM). The curved wall and the diagonal walls of the cavity are at a constant temperature of hot and cold, respectively. Nanoparticle volume fraction of 0, 0.02 and 0.04, Hartmann number of 0, 15, 30, 45 and 60, heat generation/absorption coefficient of -5, 0 and +5 and inclination angle of 45, 135 and 225 degrees are studied. The high accuracy of the results compared to previous studies confirmed the correctness of the code written in Fortran language. The results shows that in all cases, increasing the Hartmann number leads to a decrease in the maximum value of the streamlines and the average Nusselt number, with the lowest effect at 225 degrees. Also increasing the strength of the magnetic field leads to an average decrease of 28, 23 and 7% of the average Nusselt number for angles of 45, 135 and 225 degrees, respectively. Increasing the heat generation/absorption coefficient is a determining factor in the effectiveness of the magnetic field and adding nanoparticles, and increasing it reduces the amount of heat transfer. On average, heat generation reduces the average Nusselt number by 71, 98, and 145 percent for the angles of 45, 135, and 225 degrees, respectively. In general, the lowest value of the average Nusselt number is related to the angle of 225 degrees, but the effect of adding nanoparticles in increasing the average Nusselt number is the highest at this angle. Generally, an increase in the percentage of nanoparticles leads to an average increase of 12% in the average Nusselt number. The effect of nanoparticle shape is more apparent with increasing their volume fraction. The highest amount of heat transfer is related to the cylindrical nanoparticles, in which the average Nusselt number is on average about 6% higher than the spherical state.
