Showing 43 results for سرریز
S. Kouchakzadeh,
Volume 6, Issue 3 (10-2002)
Abstract
Side channel spillways have a common usage in conveyance and distribution networks, high dams, water and wastewater treatment plants, and surface drainage networks. A side channel carries spatially varied flow with increasing discharge and their water surface profiles is a main feature in the design process. Usually, the bottom width of the channel is flared in the flow direction and an end sill is also installed at the downstream end to provide a control section and to generate an even water surface profile. In this study, the impact of installing an end sill on the flow characteristics in a non-prismatic side channel is presented. Six distinct longitudinal profiles were clearly observed in each run and the difference between the mid points of the maximum and the minimum profiles of each run was used to evaluate the sill effects on the water surface profile and the energy dissipation.
The results indicated that the maximum and the minimum differences are, respectively, equal to critical depth and half of it generated at the channel downstream end. Also, based on an envelope of the data, a method was proposed to determine the maximum potential impact of an end sill that might have on the flow depth, which could also be considered as a guideline in the design process.
M. Heidarpour, H. Afzalimehr, E. Khorami,
Volume 6, Issue 3 (10-2002)
Abstract
Of the many hydraulic structures developed by man, the weir is perhaps the oldest. Weirs are used for the measurement of discharge and regulation of water flow. The most common types of weirs are broad-crested, sharp-crested, circular-crested and cylindrical, and ogee crest weirs. Advantage of the circular-crested and cylindrical weir compared to the other weirs include simplicity of design, stable overflow pattern, larger coefficient of discharge and the associated lower costs. In the present study, potential flow around a circular cylinder are adapted to determine the velocity distribution at the crest section and to develop a model for coefficient of discharge (Cd) for circular-crested weirs. These results were evaluated using present test data for three types of weir models, namely, cylindrical, semicylindrical and semicylindrical with different heights and also Dressler theory. The results of the study showed that the experimental velocity profile agree very well with the theoretical profiles for the range of the study. Also, the prediction of the velocity distribution over the weir crest using Dressler theory is always less than the proposed model and measured data. The predicted values of coefficient of discharge (Cd) based on the proposed model agree well with Cd determined from direct discharge measurements. For the cylindrical model, the coefficient of discharge can be predicted from the proposed model within an error of –7% and for the semicylindrical and semicylindrical with different heights within ± 5%.
T. Honar, M. Javan, A. Keshavarzi,
Volume 6, Issue 3 (10-2002)
Abstract
Side weirs as flow diversion devices are widely used in irrigation, land drainage and urban sewage systems. In the present study, the effects of the length and height of inclined side weir crest on discharge coefficient were investigated in prismatic and nonprismatic rectangular channels.. In this study, 675 laboratory tests were conducted.
Analysis of experimental tests showed that the discharge coefficient is strongly correlated with uptream Froude number, height of weir to depth ratio at upstream of weir, ratio of water depth on weir to length of weir, and with prismatic factor. Based on experimental results, a model is proposed. The model is capable of estimating the discharge coefficient under subcritical flow conditions. Finally, the data from the proposed model was compared with those obtained by other researchers under different side and bed slopes. There was a good agreement with a relative error of less than ten percent.
M. Heidarour, S. F. Mousavi, A. R. Roushani Zarmehri,
Volume 10, Issue 3 (10-2006)
Abstract
Because of slight variation of the static head due to discharge fluctuations, the labyrinth weirs are considered to be economical structures for flood control and water level regulation in irrigation networks, as compared to other devices. Labyrinth weirs are composed of folded sections observed as trapezoidal and triangular in plan view. In this study, rectangular and U-shaped labyrinth weirs were investigated. Experiments were conducted on 15 labyrinth weir models. The models included eight rectangular labyrinth models and six U-shaped labyrinth models with different heights and lengths, and one linear model. All the experiments were performed in a horizontal rectangular flume, 7 m long, 0.32 m wide and 0.35 m high. The results indicated that for all the models, discharge coefficient increased sharply with an increase in Ht/P and attained a maximum value. This coefficient then decreased smoothly with a further increase in Ht/P. Increasing height of weirs increased the discharge coefficient for both rectangular and U-shaped weirs. The results also showed that increasing the length parallel to the flow direction decreased and increasing the length perpendicular to the flow direction increased the discharge coefficient. Generally, the discharge coefficient for rectangular weir was less than that of the U-shaped weir. The obtained results compared with those of Tullis et al. (1995) showed that discharge coefficient for U-shaped weir is more and for rectangular weir is less than that of the trapezoidal weir for angle of the side legs of 8 and 12 degrees.
M. Yasi, M. Mohammadi,
Volume 11, Issue 41 (10-2007)
Abstract
A labyrinth spillway is an overflow spillway to regulate and control flow in canals, rivers and reservoirs. The main hypothesis for the development of such a spillway is to increase the discharge per unit width of structure for a given headwater. This type of structure is often an efficient alternative to a gated-spillway type where either the increase of the flood-passage capacity or the control of the water surface upstream is concerned. This study was aimed to investigate the hydraulic performance of labyrinth spillways of general trapezoidal planform with simple curved apexes. In the experimental work, twelve spillway models with double cycles were considered using three different curved apexes (R/w= 0.15, 0.2, 0.25), each with four different crest heights (w/P= 1.5, 2, 3, 4). Based on the cited recommendations, the length magnification was set to a constant ratio of (l/w= 3) the crest shape was to be of a semi-circular form with simple radius (r= 15 mm) and the spillway walls were vertical with the thickness of T= 2r. An intensive experiment was carried out over a wide range of flows, providing 720 flow data ranging from free flow to submerged flow conditions. 1D flow equation was presented using combined mathematical and dimensional analysis. A coefficient of discharge, Cd, was introduced to represent the influence of the effective geometric and hydraulic parameters on the flow capacity over the spillway. Modular limit was also controlled to see whether the flow over the spillway would be submerged. The results of the study indicate that the modified curved planform of the spillway apexes with consistent divergence in the downstream channel introduces a significant improvement in the flow efficiency over the labyrinth spillways. Spillways with narrower curved apexes (i.e. R/w≤ 0.2), and with the vertical-aspect ratio of (2≤w/P<3) provide more stable and higher hydraulic performance than any other labyrinth planforms over a wide range of flows (i.e. 0.10/P<0.6). In terms of the flow capacity, the proposed spillway model is shown to be more efficient than other zig-zag planforms (i.e. triangular and trapezoidal shapes) with an identical crest length.
H Faghih, M Kholghi, S Kochekzadeh,
Volume 12, Issue 46 (1-2009)
Abstract
Overtopping is one of the main factors responsible for dam failure. To avoid overtopping, dam is equipped with one or some spillways to release the water impounded in the reservoir. The number and size of these spillways are determined on the basis of design flood. Determination of design flood of dam spillway can be formulated as a multiobjective risk problem. This problem can be solved by Quantitative Risk Analysis Methods. Here, four economical design methods which are based on risk analysis including, United States National Research Council (NRC), US Civil Engineering, Unit Curve and Partitioned Multiobjective Risk (PMR) were studied. In order to compare these methods, Risk Analysis was performed for re-determining design flood of Pishin Dam Spillway. This Dam has been constructed on the Sarbaz River. Owing to the fact that the integrals of the expected damage relations in the two methods, i.e., Civil Engineering, and Partitioned Multiobjective Risk are analytically unsolvable, Romberg numerical integration technique and Excel software were utilized for the related calculations and drawing graphs. Also, in order to select suitable distribution, the flood analysis was done using Smada software. The findings of the study indicated that design flood determined by the three methods, i.e., Civil Engineering, National Research Council and Unit Curve was almost the same, and that the amount of flood was less than the 10,000-year-old flood while design flood determined by Partitioned Multiobjective Risk Method, was larger than the 10,000- year-old flood.
E Izadi, M Heidar Pour, A Kabiri Samani,
Volume 12, Issue 46 (1-2009)
Abstract
In this study, the flow characteristics have been investigated by measuring separation zone, surface and velocity profiles over the circular crested side weirs. An equation was proposed for the length of the separation zone using dimensional, statistical and regression analysis. The dimensional analysis showed that the length of separation zone depends on the upstream to the downstream water depth over the side weir, channel width to the downstream water depth and the Froude number. Comparison of the longitudinal and sectional surface profiles showed that the surface profiles at the vicinity of the side weir are non-uniform, due to separation zone close to the side weir. Therefore, the suitable place for measuring the characteristics of flow is along the centre line of the channel. It was observed that the maximum velocity occurred below the surface water which might be due to the secondary flow around the side weir. By increasing the distance far enough from the side weir, the effects of secondary flow were minimized and the velocity profiles tended to be uniform.
A Karizi , T Honar ,
Volume 14, Issue 51 (4-2010)
Abstract
Side weirs as flow diversion devices are usually used as emergency weirs in large hydraulic structures like dams and irrigation and drainage networks, because of their importance they require delicate design. As a result application of numerical and simulation models play an important role in design of these hydraulic structures. In this research, the flow pattern and shear stress distribution on broad crested side weirs with different widths and entrances along with different discharges were studied by numerical solution under two and three dimensional conditions and then the results were compared with laboratory findings. These experiments were conducted in a rectangular channel with one side weir and a length of 70 cm. Experiments were done considering rounded and sharp entrances with different rounded radii and one constant discharge with intake proportions of 40 and 60 in main and branch channels, respectively. Comparison of numerical solution and experimental results show that side weirs with rounded entrance had a noticeable shear stress reduction (arrived in the bed and sides) and non-effective spinal flow, resulting in increased intake efficiency.
M. Toozandehjani, M. Kashefipour,
Volume 16, Issue 62 (3-2013)
Abstract
One of the usual ways to dissipate excess energy in the dam's downstream is hydraulic jump. Hydraulic jump is a rapidly varied flow, in which the flow conditions change from supercritical to sub-critical with a large amount of energy loss. In this research, a combination of two water jets in the form of overflow dam and underflow through a slot on the body of an ogee dam with the USBR standard was established in order to decrease the length and sequent depth in a hydraulic jump. In these experiments, the underflow from the slot was designed with three out passages of 0, 45, and 90 degrees in respect horizontal line. Six different discharge ratios were used for each slot and the effect of each experiment conditions on decreasing of the length and sequent depth of hydraulic jump was investigated. The results showed that the confluence of two jets with 45 degrees from the slot had the maximum effect on the reducing of the length of hydraulic jump and sequent depth, and when 26 percent of the total discharge passed through the slot as underflow, it caused the length of hydraulic jump to be reduced by 50 percent in comparison with the classic jump. This slot not only decreases the length and sequent depth of hydraulic jump but also the sediment behind the dam can be evacuated through it. Moreover, it increases the discharge coefficient.
M. Heidarpoor, S. H. Razavian, Y. Hosseini,
Volume 18, Issue 68 (9-2014)
Abstract
The combined system of gate and weir is used for flow measurement in open channels. But in case the passing water has floating material and sediment it damages their performance and hence error of measurement will increase. In order to solve this problem, weir and gate can be combined and a concentrated hydraulic system known as weir-gate can be developed, thus allowing sediments transportation from under the gate and floating particles on weir. The principal goal of this study was to investigate the passing flow characteristics by trapezoidal weir and sharp-edge rectangular sluice gate in rectangular channel, and also suggest a discharge coefficient for combinational flow in different flow conditions. The experiments were carried out in laboratory channel on models with different geometric dimensions under various hydraulic conditions. Discharge coefficient was presented for various condition of passing flow of trapezoidal sharp-edge weir and below rectangular sluice gate using statistical analysis conducted on dimensionless geometric parameters affecting the flow. Resulting discharge coefficients were in agreement with laboratory results.
T. Honar, S. Mazloom Shahraki,
Volume 18, Issue 69 (12-2014)
Abstract
Cylindrical and semi-cylindrical weirs are used in water distribution systems for flow measurement in open channels and for control of water surface. Review of literature shows that cylindrical and semi-cylindrical weirs are not widely used in practice. Because of their low construction cost and simplicity, an investigation was done to study cylindrical and semi-cylindrical weirs in terms of their hydraulic characteristics such as discharge coefficient, energy loss and flow depth over the spillway crest. The research was done for 128 models in the hydraulic laboratory of water engineering department, Shiraz University. According to the results, due to flow separation from body of the weirs, flow coefficient increases in the cylindrical and semi cylindrical weirs by 57%. It was found that discharge coefficient increases by increasing the total head of upstream. Therefore, construction of cylindrical and semi-cylindrical weirs and side weir is recommended due to reduction in weir length, increased hydraulic efficiency, and reduced administrative costs compared to other wide edge side weirs.
S. Samiee, M. Heidarpour, S. Okhravi,
Volume 19, Issue 73 (11-2015)
Abstract
Side weir is the structure to evacuate extra water from a canal when level of water rises. This structure is mounted on the wall of canal. It is used predominantly to set flow in irrigation and drainage systems or urban wastewater harvesting systems. Implementing guide vanes is a simple way to increase side weir efficiency. In this study, the effect of using guide vanes on discharge and discharge coefficient of rectangular sharp-crested side weirs was investigated. ADV instrument was applied for recording vertical velocity over the crest of side weir. Local discharge was calculated by vertical velocity data for both conditions of presence and no presence of guide vanes. Results showed that in both cases, increasing the Froude number results in the decrease of passing discharge and discharge coefficient of the rectangular sharp-crested side weir. Data analysis also showed that by increasing the Froude number, guide vanes have more effect on increasing discharge coefficient and local discharge. The local discharge increased along the crest and the most passing local discharge occurred near the end of the side weir. Analysis indicates that using guide vanes leads to the increase of discharge coefficient by about 32%.
A. A. Kamanbedast, S. R. Mousavi,
Volume 20, Issue 78 (1-2017)
Abstract
Morning glory spillway is one of the spillways and used when it is not possible to use any other spillways. With the onset of submergence and flow loss, and intensification of circulation and vortexes, spillway performance decreases severely. With decreasing discharge coefficient, the height of water in the reservoir increases and the risk of dam damage, caused by the lack of spillway ability of great flow discharge, increases. Anti-vortex piers are used to solve this problem. The increase of the submergence threshold can provide ability of greater flow discharging, without spillway submergence and its negative consequences. Anti-vortex piers, in addition to correcting circulation and vortexes, may also be effective in increasing the submergence threshold. To investigate this possibility, 110 experiments were performed with the physical model on spillways with square and circular inlet section in different modes and number of anti-vortex piers. Results show that increasing number of Anti-vortex piers increases the submergence threshold and spillway can discharge greater inflow and height of water without being submerged. The effect of the overflow of the circle shape, because currents and vortexes spinning in a circle overflow is higher than square spillway. Also the maximum discharge coefficient was observed when 4 vortex breakers were installed at the angle of 90 degrees.
K. Qaderi, R. Jafarinia, B. Bakhtiari, Z. Afzali Goruh,
Volume 22, Issue 1 (6-2018)
Abstract
The investigation of local scour below hydraulic structures is so complex that makes it difficult to establish a general model to provide an accurate estimation for the local scour dimension. During the last decades, Data Driven Methods (DDM) have been used extensively in the modeling and prediction of unknown or complex behaviors of systems One of these methods is Group Method of Data Handling (GMDH), that is a self-organization approach and increasingly produces a complex model during the performance evaluation of the input and output data sets. So, the objective of this study was to investigate the potential of the GMDH method in the accurate estimation of local scouring geometry (maximum scour depth, the distance of maximum local scour depth till Ski-jump bucket and length of local scour) below the Siphon spillway with Ski-jump bucket energy dissipaters for a set of experimental data. 80% of data set was used for the training period and the remaining data set was used for the test period. The average values of MSRE, MPRE, CE and RB for the nonlinear second order transfer function (FUNC1) were calculated to be 0.92, 0.02, 8.74, -0.01; also, for the nonlinear first order transfer function (FUNC2), they were 0.85, 0.02, 10.43 and -0.02, respectively. The results indicated that the performance of FUNC1 was better than FUNC2. Also, the value of the coefficient of determination (R2) for the estimation of local scour dimension using different methods such as s linear regression, nonlinear regression and ANN indicated the high performance of the developed model of GMDH in the accurate estimation for local scour dimensions.
M. Majedi Asl, M. Fuladipanah,
Volume 22, Issue 4 (12-2018)
Abstract
A labyrinth weir is a nonlinear weir folded in the plan-view which increases the crest length and the flow rate for a given channel width and an upstream flow depth. Nowadays, a labyrinth weir is an attractive alternative for those weirs that have a problem in passing the probable maximum flood. The three-dimensional flow pattern and unlimited geometric parameters provide a major challenge to the designers of these weirs. The present study aimed at determining discharge coefficients of sharp-crested triangular labyrinth weirs using the support vector machine (SVM). The results were compared with the experimental data. For this purpose, 123 laboratory test data including geometric and hydraulic parameters such as vertex angle (θ), magnification ratio (L/B), head water ratio (h/w), Froude number (Fr), Weber Number (We) and Reynolds number (Re) were used. The results showed that the SVM-based model produced the most accurate results when only three geometric parameters, e.g. (h/w, θ, L/B), were introduced as the input parameters (R2 = 0.974, Root mean square error [RMSE] = 0.0118, mean absolute error [MAE] =0.0112 and mean normal error [MNE] =0.017 for the test stage). Also, for these weirs, polynomials linear and nonlinear regression equations were presented. Finally, the discharge coefficient of sharp-crested triangular labyrinth weirs based on the Rehbock equation was evaluated and compared with the SVM using nonlinear and linear regression methods.
H. Azarpeyvand, A. R. Emadi, M. Sedghi Asl,
Volume 23, Issue 1 (6-2019)
Abstract
Labyrinth weirs are the economic structures to increase the weir output efficiency in limited widths, which can be seen in the plane f trapezoidal and triangular forms. These weirs with a hydraulic load and fixed width pass the more discharge in comparison to other type of weirs. In this study, labyrinth weirs trapezoidal in plane form were investigated. The experiments were performed on 27 laboratory models with 9 different discharge rates and a total of 243 tests. The results showed that, in all of the composite trapezoidal labyrinth weirs, the ratio of discharge coefficient to Ht/p (Ht: Total hydraulic load and p: weir length) weir length was increased at first; after reaching the maximum rate, it started to decrease. According to the suggested general relation, the utmost impact on discharge coefficient resulted from the cycle number and Ht/p relation. Creating new labyrinth on the wing of the weir led to the increase of the effective length; as a result of it, the discharge rate increased in a specific amount of Ht/p. Also, the discharge through a trapezoidal labyrinth weir with the semicircular planform was better than the square; the square, in turn, was better than the simple trapezoidal weirs.
R. Monjezi, M. Heidarnejad, A. R. Masjedi, M. H. Pourmohammadi, A. Kamanbedast,
Volume 23, Issue 2 (9-2019)
Abstract
Nonlinear weirs are regarded as important hydraulic structures for water level adjustment and flow control in channels, rivers and dam reservoirs. One example of non-linear weirs is shaped as curved-zigzag. The crest axis of these weirs is non-linear. At a given width, the crest length is greater than that of the conventional linear weirs. Thus, they achieve a higher flow rate for an identical hydraulic load. This research experimentally focused on the discharge coefficient and flow rate of curved weirs with three different curve radii in two triangular linear and zigzag shapes. The discharge coefficients of these weirs were comparatively explored in terms of the hydraulic performance as a function of the total hydraulic load to weir crest height ratio (hd/P) and curvature angle (θ) (or curve radius). The results indicated that for the same hydraulic load, the increase of θ (the decrease in curve radius) led to a lower discharge coefficient; this was first because of the increased topical rise of water level, and then the more indirect path with a greater curvature through which the flow had to transport. Both factors could negatively affect the water discharge coefficient. In practice, the runoff coefficient at a weir with a curve radius of R/w=1.25 was approximately 8.5% greater than that of a weir with a curve radius of R/w=0.75 under a hydraulic load of 0.2.
J. Rouzegar, A. A. Kamanbedast, A. Masjedi, M. Heidarnejad, A. Bordbar,
Volume 23, Issue 3 (12-2019)
Abstract
Morning glory spillway is one of the spillways that used to passing of flood from high to low level. This spillway is used in the reservoir dams that are placed in narrow valleys and in many locations with high slope in reservoir walls. In the Morning glory spillways, the vortex flow can reduce discharge, discharge coefficient and the performance of spillway. The zigzag spillway, as another type, is introduced as a proper option for compensating the problem of passing maximum possible flow rate, usually encountered by spillways. In the present study, the experimental results of a physical model were used to develop a hydraulic design with squire and circle inlet and analysis method for Labyrinth Morning Glory Spillway. The analysis of experimental data in circle and square inlet showed, that increase in length of spillway and zigzag, causes decrease in the discharge coefficient. Finally the result of effect spillway inlet on flow rate demonstrate that discharge coefficient in square inlet is more than circle, whereas without vortex breaker.
A. Rezaei Ahvanooei, H. Karami, F. Mousavi,
Volume 23, Issue 3 (12-2019)
Abstract
In this research, by using FLOW3D, the performance of non-linear (arced) piano key (PKW-NL) in plan and linear piano key weir (PKW-L), with equal length of weir, was compared. Results showed that nonlinearity of the weir caused 20% increase in the discharge coefficient. Investigating the velocity contours for these two weir models also showed that maximum velocity within the PKW-NL weir structure is about 30% lower than the PKW-L weir. Also, the performance of non-linear piano key weir was evaluated under inward (PKW-IC) and outward (PKW-OC) curvatures to the channel. Results showed that in the case of PKW-IC weir, the discharge coefficient was increased by 8% as compared to the PKW-OC weir. Investigating the pressure contours for these two weir models also shows that the average pressure within the PKW-IC weir structure is about 5% higher than the PKW-OC weir. This increase in pressure leads to a decrease in the speed and better distribution of flow over the weir keys.
A. Saki, A. A. Kamanbedast, A. Masjedi, M. Heidarnejad, A. Bordbar,
Volume 23, Issue 4 (12-2019)
Abstract
After Hamidieh Diversion Dam near the city of Hamidieh, Karkheh River is divided into two streams known as Hufel and Nissan. At the lower flow rates, Nissan makes up a greater share than Hufel due to the steeper slope of the former. This study attempted to construct a hydraulic structure to appropriately divide water flow in Hufel. In a laboratory experiment, a flume with a 90-degree bend was used at Islamic Azad University of Ahvaz. Various experiments were conducted at different widths and heights. Furthermore, this model was simulated through CCHE2D, the results of which were compared against those of physical and mathematical models. The results indicated that the weir height increased the deviation flow percentage to the Hufel stream due to rising water level. Moreover, the deviation flow percentage to Hufel was declined as the weir width was increased due to falling water level. At Hufel, the installation of rectangular weir in different dimensions yielded the minimum of 34.3% and the maximum of 61.5% increase in the flow rate. In the normal mode without any weirs installed, however, there would be an increase in the flow rate, as compared to the mode where a weir has been installed. This can be associated with the flow controlled by the weir. On average, the deviation flow rate was increased by 2.8% in the weir mode and 7.7% in the weir-less one. An increase in the Froude number from 0.21 to 0.38 led to a lower average deviation flow rate by 19.3%. Moreover, the results of the simulation through CCHE2D were demonstrated to be largely similar to those of physical model experiments. However, an increase in the Froude number did not lead to a decline in the deviation flow rate (i.e. it remained constant). This trend was inconsistent with the results of the physical model.
