Showing 24 results for Weir
E Izadi, M Heidar Pour, A Kabiri Samani,
Volume 12, Issue 46 (1-2009)
Abstract
In this study, the flow characteristics have been investigated by measuring separation zone, surface and velocity profiles over the circular crested side weirs. An equation was proposed for the length of the separation zone using dimensional, statistical and regression analysis. The dimensional analysis showed that the length of separation zone depends on the upstream to the downstream water depth over the side weir, channel width to the downstream water depth and the Froude number. Comparison of the longitudinal and sectional surface profiles showed that the surface profiles at the vicinity of the side weir are non-uniform, due to separation zone close to the side weir. Therefore, the suitable place for measuring the characteristics of flow is along the centre line of the channel. It was observed that the maximum velocity occurred below the surface water which might be due to the secondary flow around the side weir. By increasing the distance far enough from the side weir, the effects of secondary flow were minimized and the velocity profiles tended to be uniform.
A Karizi , T Honar ,
Volume 14, Issue 51 (4-2010)
Abstract
Side weirs as flow diversion devices are usually used as emergency weirs in large hydraulic structures like dams and irrigation and drainage networks, because of their importance they require delicate design. As a result application of numerical and simulation models play an important role in design of these hydraulic structures. In this research, the flow pattern and shear stress distribution on broad crested side weirs with different widths and entrances along with different discharges were studied by numerical solution under two and three dimensional conditions and then the results were compared with laboratory findings. These experiments were conducted in a rectangular channel with one side weir and a length of 70 cm. Experiments were done considering rounded and sharp entrances with different rounded radii and one constant discharge with intake proportions of 40 and 60 in main and branch channels, respectively. Comparison of numerical solution and experimental results show that side weirs with rounded entrance had a noticeable shear stress reduction (arrived in the bed and sides) and non-effective spinal flow, resulting in increased intake efficiency.
M. Heidarpoor, S. H. Razavian, Y. Hosseini,
Volume 18, Issue 68 (9-2014)
Abstract
The combined system of gate and weir is used for flow measurement in open channels. But in case the passing water has floating material and sediment it damages their performance and hence error of measurement will increase. In order to solve this problem, weir and gate can be combined and a concentrated hydraulic system known as weir-gate can be developed, thus allowing sediments transportation from under the gate and floating particles on weir. The principal goal of this study was to investigate the passing flow characteristics by trapezoidal weir and sharp-edge rectangular sluice gate in rectangular channel, and also suggest a discharge coefficient for combinational flow in different flow conditions. The experiments were carried out in laboratory channel on models with different geometric dimensions under various hydraulic conditions. Discharge coefficient was presented for various condition of passing flow of trapezoidal sharp-edge weir and below rectangular sluice gate using statistical analysis conducted on dimensionless geometric parameters affecting the flow. Resulting discharge coefficients were in agreement with laboratory results.
T. Honar, S. Mazloom Shahraki,
Volume 18, Issue 69 (12-2014)
Abstract
Cylindrical and semi-cylindrical weirs are used in water distribution systems for flow measurement in open channels and for control of water surface. Review of literature shows that cylindrical and semi-cylindrical weirs are not widely used in practice. Because of their low construction cost and simplicity, an investigation was done to study cylindrical and semi-cylindrical weirs in terms of their hydraulic characteristics such as discharge coefficient, energy loss and flow depth over the spillway crest. The research was done for 128 models in the hydraulic laboratory of water engineering department, Shiraz University. According to the results, due to flow separation from body of the weirs, flow coefficient increases in the cylindrical and semi cylindrical weirs by 57%. It was found that discharge coefficient increases by increasing the total head of upstream. Therefore, construction of cylindrical and semi-cylindrical weirs and side weir is recommended due to reduction in weir length, increased hydraulic efficiency, and reduced administrative costs compared to other wide edge side weirs.
S. Samiee, M. Heidarpour, S. Okhravi,
Volume 19, Issue 73 (11-2015)
Abstract
Side weir is the structure to evacuate extra water from a canal when level of water rises. This structure is mounted on the wall of canal. It is used predominantly to set flow in irrigation and drainage systems or urban wastewater harvesting systems. Implementing guide vanes is a simple way to increase side weir efficiency. In this study, the effect of using guide vanes on discharge and discharge coefficient of rectangular sharp-crested side weirs was investigated. ADV instrument was applied for recording vertical velocity over the crest of side weir. Local discharge was calculated by vertical velocity data for both conditions of presence and no presence of guide vanes. Results showed that in both cases, increasing the Froude number results in the decrease of passing discharge and discharge coefficient of the rectangular sharp-crested side weir. Data analysis also showed that by increasing the Froude number, guide vanes have more effect on increasing discharge coefficient and local discharge. The local discharge increased along the crest and the most passing local discharge occurred near the end of the side weir. Analysis indicates that using guide vanes leads to the increase of discharge coefficient by about 32%.
M. Majedi Asl, M. Fuladipanah,
Volume 22, Issue 4 (3-2019)
Abstract
A labyrinth weir is a nonlinear weir folded in the plan-view which increases the crest length and the flow rate for a given channel width and an upstream flow depth. Nowadays, a labyrinth weir is an attractive alternative for those weirs that have a problem in passing the probable maximum flood. The three-dimensional flow pattern and unlimited geometric parameters provide a major challenge to the designers of these weirs. The present study aimed at determining discharge coefficients of sharp-crested triangular labyrinth weirs using the support vector machine (SVM). The results were compared with the experimental data. For this purpose, 123 laboratory test data including geometric and hydraulic parameters such as vertex angle (θ), magnification ratio (L/B), head water ratio (h/w), Froude number (Fr), Weber Number (We) and Reynolds number (Re) were used. The results showed that the SVM-based model produced the most accurate results when only three geometric parameters, e.g. (h/w, θ, L/B), were introduced as the input parameters (R2 = 0.974, Root mean square error [RMSE] = 0.0118, mean absolute error [MAE] =0.0112 and mean normal error [MNE] =0.017 for the test stage). Also, for these weirs, polynomials linear and nonlinear regression equations were presented. Finally, the discharge coefficient of sharp-crested triangular labyrinth weirs based on the Rehbock equation was evaluated and compared with the SVM using nonlinear and linear regression methods.
H. Azarpeyvand, A. R. Emadi, M. Sedghi Asl,
Volume 23, Issue 1 (6-2019)
Abstract
Labyrinth weirs are the economic structures to increase the weir output efficiency in limited widths, which can be seen in the plane f trapezoidal and triangular forms. These weirs with a hydraulic load and fixed width pass the more discharge in comparison to other type of weirs. In this study, labyrinth weirs trapezoidal in plane form were investigated. The experiments were performed on 27 laboratory models with 9 different discharge rates and a total of 243 tests. The results showed that, in all of the composite trapezoidal labyrinth weirs, the ratio of discharge coefficient to Ht/p (Ht: Total hydraulic load and p: weir length) weir length was increased at first; after reaching the maximum rate, it started to decrease. According to the suggested general relation, the utmost impact on discharge coefficient resulted from the cycle number and Ht/p relation. Creating new labyrinth on the wing of the weir led to the increase of the effective length; as a result of it, the discharge rate increased in a specific amount of Ht/p. Also, the discharge through a trapezoidal labyrinth weir with the semicircular planform was better than the square; the square, in turn, was better than the simple trapezoidal weirs.
R. Monjezi, M. Heidarnejad, A. R. Masjedi, M. H. Pourmohammadi, A. Kamanbedast,
Volume 23, Issue 2 (9-2019)
Abstract
Nonlinear weirs are regarded as important hydraulic structures for water level adjustment and flow control in channels, rivers and dam reservoirs. One example of non-linear weirs is shaped as curved-zigzag. The crest axis of these weirs is non-linear. At a given width, the crest length is greater than that of the conventional linear weirs. Thus, they achieve a higher flow rate for an identical hydraulic load. This research experimentally focused on the discharge coefficient and flow rate of curved weirs with three different curve radii in two triangular linear and zigzag shapes. The discharge coefficients of these weirs were comparatively explored in terms of the hydraulic performance as a function of the total hydraulic load to weir crest height ratio (hd/P) and curvature angle (θ) (or curve radius). The results indicated that for the same hydraulic load, the increase of θ (the decrease in curve radius) led to a lower discharge coefficient; this was first because of the increased topical rise of water level, and then the more indirect path with a greater curvature through which the flow had to transport. Both factors could negatively affect the water discharge coefficient. In practice, the runoff coefficient at a weir with a curve radius of R/w=1.25 was approximately 8.5% greater than that of a weir with a curve radius of R/w=0.75 under a hydraulic load of 0.2.
A. Rezaei Ahvanooei, H. Karami, F. Mousavi,
Volume 23, Issue 3 (12-2019)
Abstract
In this research, by using FLOW3D, the performance of non-linear (arced) piano key (PKW-NL) in plan and linear piano key weir (PKW-L), with equal length of weir, was compared. Results showed that nonlinearity of the weir caused 20% increase in the discharge coefficient. Investigating the velocity contours for these two weir models also showed that maximum velocity within the PKW-NL weir structure is about 30% lower than the PKW-L weir. Also, the performance of non-linear piano key weir was evaluated under inward (PKW-IC) and outward (PKW-OC) curvatures to the channel. Results showed that in the case of PKW-IC weir, the discharge coefficient was increased by 8% as compared to the PKW-OC weir. Investigating the pressure contours for these two weir models also shows that the average pressure within the PKW-IC weir structure is about 5% higher than the PKW-OC weir. This increase in pressure leads to a decrease in the speed and better distribution of flow over the weir keys.
A. Saki, A. A. Kamanbedast, A. Masjedi, M. Heidarnejad, A. Bordbar,
Volume 23, Issue 4 (12-2019)
Abstract
After Hamidieh Diversion Dam near the city of Hamidieh, Karkheh River is divided into two streams known as Hufel and Nissan. At the lower flow rates, Nissan makes up a greater share than Hufel due to the steeper slope of the former. This study attempted to construct a hydraulic structure to appropriately divide water flow in Hufel. In a laboratory experiment, a flume with a 90-degree bend was used at Islamic Azad University of Ahvaz. Various experiments were conducted at different widths and heights. Furthermore, this model was simulated through CCHE2D, the results of which were compared against those of physical and mathematical models. The results indicated that the weir height increased the deviation flow percentage to the Hufel stream due to rising water level. Moreover, the deviation flow percentage to Hufel was declined as the weir width was increased due to falling water level. At Hufel, the installation of rectangular weir in different dimensions yielded the minimum of 34.3% and the maximum of 61.5% increase in the flow rate. In the normal mode without any weirs installed, however, there would be an increase in the flow rate, as compared to the mode where a weir has been installed. This can be associated with the flow controlled by the weir. On average, the deviation flow rate was increased by 2.8% in the weir mode and 7.7% in the weir-less one. An increase in the Froude number from 0.21 to 0.38 led to a lower average deviation flow rate by 19.3%. Moreover, the results of the simulation through CCHE2D were demonstrated to be largely similar to those of physical model experiments. However, an increase in the Froude number did not lead to a decline in the deviation flow rate (i.e. it remained constant). This trend was inconsistent with the results of the physical model.
R. Gharibvand, M. Heidarnejad, H. A. Kashkouli, H. Hasoonizadeh, A. Kmanbedast,
Volume 24, Issue 1 (5-2020)
Abstract
The flow fields over a trapezoidal labyrinth weir (two-cycle) and a piano key weir were simulated using Flow3D, studying the impact of each model on the flow field in the weirs and the coefficient of discharge in comparison with the available experimental data. Moreover, the models were investigated experimentally in a 12.5 m long, 0.3 m wide, and 0.4 m high rectangular flume under clear-water conditions. The results showed good agreement between the data from the numerical and experimental models. The piano key weirs had a higher coefficient of discharged compared with labyrinth weirs. The coefficient of discharge was observed to increase by 26 percent as the height of the PKW was increased by 50 percent (from 5 to 7.5 cm). This increase was 24 percent for labyrinth weirs.
A. Alizadeh, B. Yaghoubi, S. Shabanlou,
Volume 24, Issue 2 (7-2020)
Abstract
In this study, the discharge coefficient of sharp-crested weirs located on circular channels was modeled using the ANFIS and ANFIS-Firefly (ANFIS-FA) algorithm. Also, the Monte Carlo simulations (MCs) were used to enhance the compatibilities of the soft computing models. However, the k-fold cross validation method (k=5) was used to validate the numerical models. According to the input parameters, four models of ANFIS and ANFIS-FA were introduced. Analyzing the numerical results showed that the superior model simulated the discharge coefficient as a function of the Froude number (Fr) and the ratio of flow depth over weir crest to the weir crest height) h/P(. The values of the mean absolute relative error (MARE), root mean square error (RMSE) and correlation coefficient (R) for the superior model were calculated 0.001, 0.002 and 0.999, respectively. However, the maximum error value for this study was less than 2%.
A. R. Bahrebar, M. Heidarnejad, A. R. Masjedi, A. Bordbar,
Volume 25, Issue 2 (9-2021)
Abstract
The combination of a labyrinth weir with an orifice is a proper solution for floating material to pass over the weir and transfer sediment through the orifice. Additionally, creating a slot in the overflow wing leads to higher discharge. This study examined four discharges (5, 10, 15, and 20 liters per second) with channel width and height of 30 and 40 cm in trapezoidal-orifice, square-orifice, and triangular-orifice labyrinth weirs in the laboratory and using Flow3D with RNG k-epsilon (k-ε) turbulence model, the results were compared with one another. Comparing the discharge flow over weirs and measuring the discharge coefficient among the mentioned models showed that the triangular-orifice labyrinth weir had the highest discharge rate. Moreover, the increased Ht/P ratio (Ht represents total hydraulic head; P denotes weir height) for all models resulted in the increased discharge coefficient. Due to the efficiency of this type of weirs, the highest discharge coefficient was obtained at low Ht/P ratios. At lower ratios, since there was free flow, the coefficient of weir discharge increased, and as the ratio increased, the weir was partially submerged. Furthermore, for the weir design, the best Ht/P ratio was between 0.13 to 0.41, and the maximum discharge coefficient (Cd = 1.2) was within this range.
J. Meshkavati Toroujeni, A.a. Dehghani, A. ٍemadi, M. Masoudian,
Volume 25, Issue 3 (12-2021)
Abstract
One of the crucial problems that exist in the irrigation networks is the fluctuation of the water surface flow in the main channel and changes in the flow rate of the intake structure. One of the effective methods to decrease these fluctuations is increasing the weir crest length at the given width of the channel with the use of the labyrinth weirs can be achieved for this purpose. The labyrinth weir is the same linear weir that is seen as broken in the plan view. In this study, a labyrinth weir with a length of 3.72 m, three different heights of 15, 17, and 20 cm, three different shapes of dentate (rectangular, triangular, and trapezoidal), and a linear weir were used in a recirculating flume with 15 m length and 1 m width. The result showed that for a given length and height of weir, with the increasing of the upstream water head to the weir height ratio (
), the discharge coefficient decreases. The results showed that by increasing weir height, the discharge coefficient decreases for a given length of the weir. Linear weir and labyrinth weir without dentate create more water depth at the upstream by 3.3 and 1.2 fold compared with dentate labyrinth weir.
H. Elahifar, O. Tayari, N. Yazdanpanah, M. Momeni,
Volume 25, Issue 4 (3-2022)
Abstract
The discharge coefficient of labyrinth weirs increases with increasing the crest length in a certain width range. The present research was carried out in a laboratory flume with a length of 8 m, a width of 0.6 m, and a height of 0.6 m. The discharge coefficient of two-cycle symmetric and asymmetric rectangular labyrinth weirs was experimentally measured. The dimensional analysis by the Buckingham π theorem indicated that the discharge coefficient was dependent on Se, B/Wavg, Ht/P, and WL/WR. According to the results, the discharge coefficient decreased with increasing the hydraulic head in the symmetric and asymmetric labyrinth weirs and the linear weir. Asymmetric labyrinth weirs with a WL/WR of 2.05 outperformed symmetric labyrinth weirs with a WL/WR of 1. Quantitatively, the discharge coefficient of the labyrinth weir with a B/Wavg of 3.1 was respectively 21% and 94% higher than that with a B/Wavg of 2.93 and 2.76. The discharge coefficient of the labyrinth weir with a WL/WR of 2.05 was 10-27% higher than that with a WL/WR of 1. The discharge coefficient of the linear weir was 60-250% higher than that of labyrinth weirs.
M. Sabouri, A.r. Emadi, R. Fazloula,
Volume 26, Issue 2 (9-2022)
Abstract
A compound sharp-crested weir is often used to measure a wide range of flows with appropriate accuracy in open channels. In this study, experiments were performed to investigate the hydraulic flow through a compound weir of circular-rectangular with changes in hydraulic and geometric parameters in free and submerged flow conditions. The characteristics of the weirs include rectangular spans width of 39 cm, a circular radius of 5, 7.5, and 12.5 cm, and heights of 10 and 15 cm. The results showed that by increasing the radius and height of the Weir, upstream water depth increases around 28.4%. At a constant h/p, the discharge coefficient increases with the increasing radius of the circular arc. Also, in the submerged conditions, the discharge coefficient is less (around 40%) than in the free flow condition, which is due to the resistance of the depth of the created stream against the passage of the flow.
M. Sadeghi, T.o. Naeeni, F. Kilanehei, M. Galoie,
Volume 26, Issue 3 (12-2022)
Abstract
One of the most important hydraulic structures in a dam is the spillway. The design of the ogee spillway crest is based on the lower profile of the free-flow jet passing through the sharp-crested weir. When the downstream ogee spillway profile for the design discharge conforms to the lower profile of the free-jet passing through the sharp-crested weir, the pressure on that surface of the spillway becomes zero. In this study, the design of the ogee spillway was performed initially based on both two- and three-dimensional numerical modeling and then compared to the USBR standard method. The comparison of the final numerical and analytical results showed that although the vertical two-dimensional outputs were completely in agreement with the USBR standard profile, the three-dimensional profiles were different because in this model, guide walls were not considered. According to the analysis, if the flow entering the spillway is parallel to its axis, the lower profile of the sharp-edge spillway will be in complete agreement with the standard profile. Since, the design of guide wall geometry for ogee spillways is carried out using physical modeling which iteratively revises during a high-cost trial and error procedure, this research based on the case study of the spillway of Karun-3 dam has been tried using numerical modeling. The closest geometry to the geometry of the overflow guide wall was obtained which creates the least difference in transverse velocities. In this way, the design of guide walls can be done with more accuracy and low cost in comparison to physical modeling.
M. Majedi Asl, T. Omidpour Alavian, M. Kouhdaragh, V. Shamsi,
Volume 27, Issue 3 (12-2023)
Abstract
Non-linear weirs meanwhile economic advantages, have more passing flow capacity than linear weirs. These weirs have higher discharge efficiency with less free height upstream compared to linear weirs by increasing the length of the crown at a certain width. Intelligent algorithms have found a valuable place among researchers due to their great ability to discover complex and hidden relationships between effective independent parameters and dependent parameters, as well as saving money and time. In this research, the performance of support vector machine (SVM) and gene expression programming algorithm (GEP) in predicting the discharge coefficient of arched non-linear weirs was investigated using 243 laboratory data series for the first scenario and 247 laboratory data series for the second scenario. The geometric and hydraulic parameters were used in this research including the water load (HT), weir height (P), total water load ratio (HT/p), arc cycle angle (Ɵ), cycle wall angle (α), and discharge coefficient (Cd). The results of artificial intelligence showed that the combination of parameters (Cd, H_T/p, α, Ɵ) respectively in GEP and SVM algorithms in the training phase related to the first scenario (Labyrinth weir with cycle wall angle 6 degrees) were respectively equal to (R2=0.9811), (RMSE=0.02120), (DC=0.9807), and (R2=0.9896), (RMSE=0.0189), (DC=0.9871) in the second scenario (Labyrinth weir with a cycle wall angle of 12 degrees) it was equal to (R2=0.9770), (RMSE=0.0193), (RMSE=0.9768), and (R2 = 0.9908), (RMSE = 0.0128), (DC = 0.9905), which compared to other combinations has led to the most optimal output that shows the very favorable accuracy of both algorithms in predicting the coefficient the Weir discharge is arched non-linear. The results of the sensitivity analysis indicated that the effective parameter in determining the discharge coefficient of the arched non-linear Weir in GEP and in SVM is the total water load ratio parameter (HT/p). Comparing the results of this research with other researchers revealed that the evaluation indices for GEP and SVM algorithms of this research had better estimates than other researchers.
S. Barani, M. Zeinivand, M. Ghomeshi,
Volume 27, Issue 4 (12-2023)
Abstract
In this study the effect of orifice number and dimensions in combined structure sharp crested rectangular weir with multiple square orifice was investigated. For this propose, some experiments in different flow rate, different orifice number and dimensions were done. The results showed that by different orifice numbers and dimensions, flow discharge increased at the same upstream flow head. This increasing trend was observed in all numbers and dimensions of the investigated experiments. The analysis of the quantitative results showed that by increasing the number of orifices, the discharge rate through the combined structure of weir-orifice was increased on average 2.06 liters per second and by increasing each centimeter of orifice dimensions, the discharge was increased by 2.82 liters per second. Also by calculating the percentage of flow rate increase, it was observed that by adding the orifice number, it increases by 18.7% and by increasing the size of the orifice by one centimeter, the flow rate increases by 28.1%.
M. Majedi Asl, T. Omidpour Alavian3, M. Kouhdaragh,
Volume 27, Issue 4 (12-2023)
Abstract
Weirs of the labyrinth have some advantages including the high coefficient of the irrigation of weir and the low fluctuation of water when the flow passes over the crest of the weir. In this research, the flow rate coefficient has been investigated by changing the weir geometry in terms of wall slope, arc cycle angle, and nose length change in the upstream and downstream of each cycle of the trapezoidal arc labyrinth weir. A total of 240 tests have been performed on 16 different physical models in a channel with a width of 120 cm and a narrowing of 20 cm from each wall. All models have been compared with the control model (normal labyrinth weir) (80A). The results showed that the 80B weir with an arc cycle angle of 20 degrees and without wall slope has a better performance than other weirs. Also, the weir with an arc cycle angle and a wall slope of 20 degrees in a divergent form (D20B) in the area (Ht/P) <0.31 has a better performance than other weirs with an arc cycle angle of 20 degrees, and after this area, the weir with a wall slope of 10 degrees has performed better in divergent form (D10B). In weirs with different cycles at an arc cycle angle of 20 degrees, the labyrinth weir with 5 cycles (N5) has performed better up to the point (Ht/P)=0.36. Also, at the maximum point, the difference is 13 and 17%, respectively, compared to the 4-cycle and 3-cycle weirs.
