Showing 51 results for Carbon
N. Enayatizamir, M. Noruzi Masir, A. Ghadamkhanii,
Volume 23, Issue 4 (2-2020)
Abstract
The soil organic matter plays an important role in increasing agricultural products and various nutrient cycle in the soil due to its effect on the physical, chemical and biological properties of soil. There is, however, little information regarding the effect of growth promoting bacteria on biological indices and different forms of carbon in agricultural soils of the country. Therefore, this study was aimed to investigate the effect of plant growth promoting bacteria on soil respiration, microbial quotient, organic carbon, microbial carbon biomass, permanganate oxidizable carbon, cold water extractable organic C, and hot water extractable organic C under the cultivation of wheat, Chamran cultivar. The experiment was conducted in greenhouse condition as a randomized complete design with 9 replications. Treatments consisted of bacterium inoculation (without inoculation, Enterobacter cloacae Rhizo_33, Enterobacter cloacae Rhizo_R1
and mixof both bacteria). During the experiment, some characteristics such as plant height and chlorophyll index were measured. At the end of the cultivation period, root and aerial part dry weight and grain yield were determined. Biological properties and different forms of carbon in the soil were measured after cultivation. The results indicated the applied plant growth promoting bacteria increased chlorophyll index, height, root and shoot dry weight and grain yield, as compared to the control. The minimum value of pH and the highest amount of each carbon forms were obtained by soil inoculation with different strains of bacteria, as compared to the control. The highest value of organic carbon was observed in the presence of the consortium of both bacteria with 22.7% increase, as compared to the control. The highest amount of microbial carbon biomass was, respectively, measured in the treatments containing consortium of bacteria, Enterobacter cloacae Rhizo_R1, Enterobacter cloacae Rhizo_33 with 87.67, 42 and 26.5% increment, as compared to the control. A positive and significant correlation was observed between cold and hot water extractable organic carbon, dissolved organic carbon and permanganate oxidizable carbon with soil respiration and there was a negative correlation between mentioned properties and the soil pH. The use of microbial inoculants increased the carbon content of the soil, which can play a positive role for improvement of physical and chemical properties of the soil and plant yield.
M. Maleki-Kakelar, M. Yavari,
Volume 24, Issue 1 (5-2020)
Abstract
Biocementation through microbial induced carbonate precipitation (MICP) is a recently developed new branch in geotechnical engineering that improves the mechanical properties of bio-treated soils. The potential application of MICP to handle problems such as liquefaction and erosion has been established; this technique offers an environmentally friendly, cost-effective and convenient alternative to traditional soil improvement approaches. Nevertheless, in spite of the widespread demonstration of the process at laboratory scale, few field and practical applications have been implemented to assess the efficiency of the biochemical process. Therefore, this paper presents a review of the utilization of MICP for soil improvement and discusses the treatment process including the key constituents involved and the main affecting factors, especially in field scale applications. The major contribution of this research is to identify the main parameters restricting the application of this method on site. Finally, technical and commercial progress in the industrial adoption of the technology and the main challenges that are ahead for the future research prior to real practical application are briefly discussed.
M. J. Rousta, S. Afzalinia, A. Karami,
Volume 24, Issue 1 (5-2020)
Abstract
Given the various advantages of applying conservation tillage methods in the agriculture, including reducing the effects of climate change by decreasing the carbon dioxide emissions to the atmosphere caused by carbon sequestration in soil, this study was conducted with two wheat-cotton and wheat-sesame rotations at Agricultural Research Station Bakhtajerd, in Darab, the southeast of Fars Province, which had a warm and dry climate; this work was carried out in a loam soil during four years. The aim of this investigation was to compare the carbon sequestration (CS) in the soil after application of different conservation tillage methods with the conventional method. The results showed that in wheat-cotton rotation, the maximum and minimum amount of CS in the 0-20 cm depth of soil with the average 17.160 and 13.810 t/ha could be obtained by using no-till and conventional tillage, respectively. Therefore, no-till increased CS by 24.26% in wheat and cotton cultivation, as compared to the conventional tillage. The economic value of this CS increment for the environment was $2459 per hectare. In the wheat-sesame rotation, the highest and lowest CS was obtained with an average of 25.850 and 12.505 t/ha in no-till and conventional tillage, respectively. Namely, direct seeding of wheat and sesame increased the CS at the 0-20 cm depth of soil by 107%, as compared to the conventional tillage with the economic value of $9809.5 per hectare. Under similar conditions, in wheat-cotton and wheat-sesame rotations, the conventional methods could be replaced by no tillage.
A. Abdollahi, M. Norouzi Masir, M. Taghavi, A. Moezzi,
Volume 24, Issue 2 (7-2020)
Abstract
Nowadays, one of the ways to confront with the micronutrients deficiency is application of Nano materials to increase the availability of elements such as zinc for plants. Therefore, this study was conducted to investigate the effect of functionalized iron oxide nanoparticles and zinc sulfate chemical fertilizer on the zinc chemical forms in soil solution phase and its correlation with zinc concentrations and uptake in wheat. This study was carried out in a completely randomized design with three replications. Treatment consisted of functionalized iron oxide nanoparticles of Hydroxyl (OH), Carboxyl (COOH) and Amine (NH2), each at three levels (100, 200 and 300 mg.kg-1), ZnSO4 (40 kg.ha-1) and Control (without using iron oxide nanoparticles). At the end of the cultivation period, soil chemical properties such as pH, soil available zinc and dissolved organic carbon and concentrations and the uptake of zinc in plant were measured. The results showed that pH, available zinc and dissolved organic carbon content of soil solution were significantly affected by the treatments. The results obtained from the Visual MINTEQ Geochemical model showed that the highest amount of the free form of zinc (Zn2+) was obtained at the level of 300 mg.kg-1 of carboxyl iron oxide nanoparticles. Also, the experimental treatments significantly influenced the concentration of Zn-DOM species. The positive and significant correlation between Zn+2 and Zn- DOC species with the concentration and total Zn uptake of wheat indicated that these pools of Zn could be liable species in soil. The results of this study, therefore, showed that the application of functionalized iron oxide nanoparticles could help to improve soil conditions in order to increase the zinc availability for plants.
S. Abdi Ardestani, B. Khalili, M. M. Majidi,
Volume 25, Issue 1 (5-2021)
Abstract
Long-term drought effect is one of the main factors of global climate change, with consequences for soil biogeochemical cycling of carbon and nitrogen and the function of soil ecosystem under drought conditions. We hypothesized that 1) the Bromus inermis, Dactylis glomerata and festuca arundinacea species would differ in their rhizosphere responses to drought and 2) combined plant species and drought would have offsetting effects on the soil biological traits. We tested these hypotheses at the long-term drought field expreiment at the Lavark Farm of Isfahan University of Technology by analyzing soil microbial biomass carbon and nitrogen and activity of β-glucosaminidase in the rhizosphere of Bromus inermis, Dactylis glomerata and festuca arundinacea species. Soil microbial biomass carbon and nitrogen responses to drought depended on plant species, such that the highest MBC was recorded in the Bromus inermis rhizosphere, while the lowest was in the Dactylis glomerata rhizosphere, thereby suggesting the greater microbial sensitivity to drought in the Dactylis glomerata rhizosphere. Genotype variations (drought tolerate and sensitive) mostly affected the change in the β-glucosaminidase activity, but they were not significantly affected by drought treatment and plant species. In general, the positive effects of the plant genotype could offset the negative consequences of drought for soil microbial biomass and traits.
S. Jafari, M. Karimzadeh, A. Abdeshahi,
Volume 25, Issue 2 (9-2021)
Abstract
Characteristics of most soils in arid and semi-arid regions affected by carbonates. The study aimed to determine the distribution of carbonates in the size components of some soils in Khuzestan province. Upward to the bottom of Karun, Karkheh, and Jarahi rivers were studied at depths of 0-50, 50-100, and 150-100 cm. The results showed that the average amount of carbonates in the soils of the Jarahi river basin (37%) was significantly different from the amount in the soils of the other two rivers (33%). Carbonates were observed in all soil size components but the maximum was present in the clay component. The highest regression relationship between soil particles was in the clay component (0.375). The highest percentage of particle reduction after carbonate removal was related to coarse silt particles (0.75). Therefore, the soil texture changed from clay in Jarahi, from clay and silty clay in Karun, and silty clay in Karkheh due to the removal of carbonates to sandy loam. There was no significant difference in the distribution of carbonates at different depths for river soils and all studied soils. The relatively uniform distribution of carbonates in the four components studied in these soils from the surface to the depth showed that the carbonates originated from the parent material, namely alluvial flood sediments of these rivers.
F. Sadeghdoust, N. Ghanavati, A. Nazarpour,
Volume 25, Issue 4 (3-2022)
Abstract
Street dust is mainly affected by the pollution of polycyclic aromatic hydrocarbons (PAHs). PAHs are a group of organic pollutants consisting of two or more benzene rings and are mainly produced during incomplete combustion. PAHs have attracted widespread attention due to their high carcinogenic and mutagenic properties in humans. Therefore, the purpose of this study was to investigate the sources and extent of the impact of these compounds on human health and the environment. To achieve this goal, 30 dust samples were collected from the sidewalks of the main streets of Dezful and the concentration of PAHs was determined by gas chromatography-mass spectrometry (GC-MS). The total concentration of PAHs in street dust of Dezful varied from 562.85 to 51447.10 μg / kg. The ratio of carcinogenic compounds to total PAHs was in the range between 0.73 to 0.91. Low molecular weight and high molecular weight PAHs accounted for 12% and 88% of total PAHs, respectively. The most important sources of PAHs in Dezful are the combustion of fossil fuels and petroleum products and emissions from vehicles and traffic. Moreover, incremental lifetime cancer risk (ILCR) in pathways ingestion in children was higher than in adults, but the ILCR in pathways dermal contact and inhalation in adults was higher than in children. The total cancer risk (CR) for children (5.77×10-3) was higher than adults (5.56×10-3), which shows the high potential for CR in the study area.
A.r Modares Nia, M. Mirmohamad Sadeghi, A. Jalalian,
Volume 25, Issue 4 (3-2022)
Abstract
Desertification has become one of the main problems of human societies living in the vicinity of desert areas in recent years. One of the methods that have been considered in recent years and are rapidly expanding in the field of soil mechanics is the Microbial Induced Carbonate Precipitation (MICP). In this method, urea-positive organisms that are naturally present in the soil can stabilize the soil and improve its engineering parameters by using urea and calcium chloride. Recently, attempts have been made to use this method to create a crustal layer on the soil to prevent wind erosion. In the present study, the effect of environmental conditions in deserts such as temperature and sand bombardment on microbial soil treatment has been investigated using this new method. The soil of the Segzi region as one of the main centers of dust in the Isfahan region was studied in this research. Therefore, the improved samples are subjected to regional temperatures which increased the surface layer resistance with increasing temperature. Also, the sandstorm conditions of the region were simulated using three different grain sizes of sand inside the wind tunnel. The results of these experiments showed that stabilized soil could withstand the conditions at wind speeds of 7 and 11 m/s. However, by increasing the wind speed to 14 m/s and the grain size, the crustal layer destroys and increases the wind erosion of the soil. Also, the resistance of the surface layer increased by increasing temperature in the tested samples. This increase in resistance continued up to 24 degrees with a high slope, but from 24 degrees onwards, this slope decreases. Based on the results of this research, it can be said that the microbial improvement method can be used as an alternative method in the future to stabilize desert soils.
A.r. Eftekhari, M. Mirmohammad Sadeghi, A. Jalalian,
Volume 27, Issue 2 (9-2023)
Abstract
The use of biotechnology-based methods in the field of geotechnical engineering has led to the birth of new knowledge of biogeotechnology and several studies have been conducted using this new knowledge in various geotechnical issues including reducing permeability and increasing shear strength, especially in sandy soils and the desired results have been obtained. Nevertheless, little research has been done using biogeotechnology in the field of improving the mechanical properties of clay soils, especially in reducing the swelling of expansive soils, which is considered one of the types of problematic soils. The main cause of swelling of expansive soils is the presence of montmorillonite clays in these types of soils. Using chemical additives to stabilize expansive soils such as lime and cement is a common practice. However, environmental concerns related to greenhouse gas production caused by the production of chemical substances and the destructive effects of these substances on the environment and soils have encouraged researchers to use other sustainable stabilization alternatives. Microbial Induced Carbonate Precipitation (MICP) is a technique that can be a promising solution to solve this problem. The objective of the present study was to investigate the effect of the MICP method on the swelling of expansive clay soils and its effect on the mechanical strength of this type of soil. One-dimensional swelling tests, uniaxial compressive strength tests, and Atterberg limits tests were performed on clay soil with a liquid limit of 53 using Sporosarcina pasteurii bacteria, calcium chloride, and urea as nutrients. Taguchi's method was used for the design of the experiments and the statistical analysis of the results. This method designs experiments through partial factorial and reduces their number without a significant effect on the results. Bacterial concentration, nutrient molarity ratio, treatment time, and soil moisture were selected as four factors with Four levels of variation. The results showed that the (MICP) method was effective in reducing the swelling potential of expansive soils and also caused a significant increase in the unconfined compressive strength of the soil and its undrained shear strength.
Miss S. Bandak, A.r. Movhedei Naeani, Ch.b. Komaki, M. Kakooei, J. Verrlest,
Volume 27, Issue 3 (12-2023)
Abstract
Soil organic carbon (SOC) is one of the most important components of soil physical and chemical properties that have an important role in sustainable production in agriculture and preventing soil degradation and erosion. Data mining approaches and spatial modeling besides machine learning techniques to investigate the amount of soil organic carbon using remote sensing data have been widely considered. The objective of the present study was the evaluation of SOC using the remote sensing technique compared with field methods in some areas of the Gonbad Kavous and Neli forests of Azadshar. The soil samples were collected from the soil surface (0-10 cm depth) to estimate the SOC. Data were categorized into two categories: 70% for training and 30% for validation. Three machine learning algorithms including Random forest (RF), support vector machine, extra tree decision, and XGBoost were used to prepare the organic soil carbon map. In the present study, auxiliary variables for predicting SOC included bands related to Lands 8 OLI and sentinel 2 measurement images, topography, and climate. The results showed that the extraction of the components related to the bands along with the calculation of indicators such as normalized vegetation difference, wetness index, and the MrVBF index as auxiliary variables play an important role in more correct estimation of the amount of soil organic matter. Comparison of different estimation regressions showed that the Sentinel 2 random forest model and in Landsat8 with the values of coefficient of determination (R2), root mean square error (RMSE), and mean absolute error (MEA) of 0.64, 0.05, and 0.17, respectively, was the best performance ratio compared to other approaches used in the study to estimate the organic carbon content of surface soil in the study area. In general, the results of this study indicated the ability of remote sensing techniques and learning models in the spatial estimation of soil organic carbon. So, this method can be used as an alternative to laboratory methods in determining soil organic carbon.
M. Kashi, S. Alizadeh Ajirlo, N. Najafi,
Volume 28, Issue 1 (5-2024)
Abstract
The reduction of water resources due to the issue of global climate change and population growth is one of the most critical issues facing the designers and planners of the development of green spaces in cities. Against these challenges, there is an urgent need to improve the efficiency of water consumption and chain use of water resources with suitable options. Due to the significant volume of urban wastewater Effluent, its reuse in green space irrigation is important from the point of view of water resource management from an ecological and economic point of view. The effect of the Parand city wastewater treatment plant on the chemical properties of soil under the cultivation of three types of cover crops (Frankinia (FR), Festuca (FE), Dichondra (DI)) in a bed with sandy loam soil is investigated. This study was conducted as a factorial experiment based on a completely randomized design using mixing of water and Effluent at 4 levels with irrigation treatments of zero (control), 50, 75, and 100% compared to fresh water and 3 replications, and then the soil chemistry characteristics such as pH, EC, OC, Na, Cl, Ca, and Mg were evaluated. The results obtained from the soil chemical analysis parameters showed that the pH value decreased in all the treatments with effluent compared to the control, and this decrease was not significant in any treatment. The values of EC and Cl have increased in all plants, and these values were significant in the FR100 treatments with an increase of about 195 and 561% compared to the control, and in the FE100 treatment with an increase of about 54 and 162%, respectively, at the 5% probability level. The amount of OC in the FR100 treatment was significant with an increase of about 41% compared to the control treatment, but in other plants, this ratio was not significant in any treatment. The maximum amount of Mg in the FR50 treatment was 30.27, which has a significant effect compared to other treatments. The amount of Na and Ca in the FR100 treatment was significant with an increase of about 343% and 130%, respectively, compared to the control treatment, while in FE and DI plants, this ratio was not significant in any treatment.
