JWSS - Journal of Water and Soil Science

---

In this study, the transport of nalidixic acid-resistant Escherichia coli (E. coli NAR) through two soils of sandy loam and clay loam was investigated. Saturated and unsaturated flow conditions were applied at two temperatures of 5 and 20ºC. Leaching was done using large repaired soil columns which had been subjected to physical weathering. A 20-cm diameter disk infiltrometer was set up to establish the steady-state flow conditions. Effluent was sampled at three depths of 15, 30 and 45 cm of soil columns. Saturated flow condition, temperature of 20 ºC and clay loam soil resulted in increasing the bacteria concentration in the leachate. Filtration coefficient and relative adsorption indices in sandy loam soil (average flow conditions, temperature and depth) were greater than those of clay loam soil with the respective values of 33% and 23%. These results may be related to the instability of soil structure and abundance of micropores in the sandy loam columns. In other words, the bacteria were physically blocked and entrapped in the fine pores of sandy loam soil. Effluent bacteria concentration decreased by depth of soil column, indicating the effect of soil on bacterial filtration as a natural filter. Leaching with cold water led to decrement of flow rate and consequently increment of bacterial filtration in the two soils of clay loam and sandy loam (average flow conditions, temperature and depth) with the respective values of 100% and 68%.

---

The effects of soil intrinsic properties on soil structural stability were evaluated. Soil samples (33 series) with wide ranges of properties and structural stability were collected from Hamadan province. Two structural stability indices were used: mean weight diameter (MWD) using Yoder method and De Leenheer-De Boodt index (DDI). Wetting pre-treatments (fast wetting to saturation and slow wetting to a matric suction of 30 kPa) were applied before wetting. Linear and multiple regression relations of MWD and DDI with the soil intrinsic properties (organic matter, clay, fine clay, silt, sand, calcium carbonate, EC and pH) were assessed. Results showed that organic matter had the highest impact on the two mentioned indices. Following organic matter, clay, fine clay and calcium carbonate were ranked respectively one after another. Fast wetting caused a higher aggregate break-down, due to its destructive energy, air entrapment, and non-uniform swelling of the soil whereas slow wetting exhibited better differentiation of soils with low structural stability. The findings of this research demonstrated high agreement (R2>75%) between the MWD and DDI, recommended both to be used for evaluating of the aggregate stability in Hamedan province

---

In agriculture, cow manures are used to enhance soil fertility and productivity. Escherichia coli is the most common fecal coliform in cow manure and considered as an index for microbial contamination of groundwater resources. The objective of this study was to investigate the transport of Escherichia coli (released from cow manure) through the field soil. Lysimeters (with internal diameter of 20.5 and height of 50 cm) were inserted into an in situ clay loam soil. Unsaturated soil water flow was controlled at an inlet matric potential of –5 cm using a tension infiltrometer. When the steady-state flow was established, air-dried fresh cow manure was applied on the lysimeters at a rate of 10 Mg ha-1 (dry basis) and the soil-manure leaching started. Soil solution was sampled at 1, 2, 4, 6, 12 and 24 h after leaching initiation using plastic samplers installed at depths of 20 and 40 cm. Concentrations of Escherichia coli in the soil solution (C) and the influent (C0) were measured using the plate count method. Impacts of soil depth, sampling time, and their interaction on C and C/C0 were significant (P<0.01). In all leaching times, relative adsorption index (SR) was lower when both soil layers were considered and the filtration increased with soil depth. When the concentration was corrected for the second layer (i.e. 20–40 cm), the SR values in this layer were considerable and greater than those in the first layer at 4 and 6 h. The influence of surface layer was substantial in bacterial filtration however, the preferential flows especially in the initial leaching times resulted in bacterial movement towards the second layer. Temperature drop reduced bacteria release from the manure, increased viscosity of the flowing water, and consequently diminished significantly the bacteria concentration in the soil solution at 24 h. Overall, it was found that similar to surface layer, subsurface layer might have great role in bacterial filtration due to its higher clay and carbonate contents

---

This study was conducted to investigate the effect of water salinity and sodicity on pore size distribution and plant-available water of two clay and sandy clay loam calcareous soils. All combinations of water EC values of 0.5, 2, 4 and 8 dS m-1 and SAR values of 1, 5, 13 and 18 (in total 16 solutions) were used to wet and dry the soil samples for five cycles. Then, water retention of the soil cores was measured at matric suctions of 0 (θs), 10 (θ10) 100 or 300 cm (θFC) and 15000 cm (θPWP). The following quantities were calculated: the difference between θ100 or θ300 and θ15000 considered as available water contrent, the θs and θ10 as macrorosity, the θ10 and θ100 as mesoporosity, and the θ100 as microrosity. The initial porosity of both soils was similar, but the greater values of pore indices and θFC, θPWP and AWC were measured in the clay soil due to clay swelling. As water EC increased, mesopores were destructed and altered to macropores and micropores. Salinity altered the mesopores into macropores due to contraction of diffuse double layer and particle’s flocculation and consequently decreased the θFC, and created new micropores which were responsible for the higher value of θPWP. These trends ultimately diminished the AWC. As water SAR increased, mesopores were destructed and altered to micropores but it did not significantly affect the macropores. With increment of SAR, both θFC and θPWP increased due to structural distruption clay swelling and dispersion resulting in increased adsorptive and interlayer surfaces. The increasing effect of SAR on θPWP was greater and more distinct so that AWC was reduced. As a result, high values of SAR of irrigation water decreased the soil available water to plants besides its toxicity and hazardous effect on plants. With increment of irrigation water salinity, the destructive impacts of SAR diminished. The influence of water quality on water retention was pronounced for the clay soil.‎

---

Hardsetting phenomenon is an indicator of poor soil physical quality. Hardsetting soils are soils with high rate of mechanical strength increase upon drying and are hardened and/or compacted when dry out. It is difficult to till such soils. Hardsetting soils have additional limitations such as poor aeration at wet conditions, low infiltrability and high runoff and erosion. Most of Iran soils have low organic matter content and it is expected that hardsetting phenomenon occurs in some of these soils. This study was conducted to investigate the hardsetting phenomenon on 9 soil series collected from Hamadan province. Three types of mechanical strength consisting tensile strength (ITS), unconfined compressive strength (UCS), and penetration resistance (PR) were measured on the repacked soil samples prepared in the lab. The ITS, UCS and PR tests were done on the soil cores which had been prepared at bulk density (BD) equal to 90% of critical BD for root growth (0.9BDcritical). The effects of intrinsic properties on the hardsetting phenomenon were studied, too. Based on the suggested definition in “International Symposium on Sealing, Crusting and Hardsetting Soils” to International :::union::: of Soil Science, in which a hardsetting soil has air-dry tensile strength ≥ 90 kPa, one soil (medium-textured) out of the studied soils showed the hardsetting phenomenon at 0.9BDcritical. It might be concluded that medium-textured soils are more susceptible to hardsetting. For all of the studied soils, the ITS increased with the increase in clay content. The increasing impacts of clay and carbonate contents were also observed for the UCS and PR, respectively. Calcium carbonate could act as a cementing agent in between the soil particles and brings about the soil susceptibility to hardsetting. Moreover, the decreasing trend of all soil mechanical strengths was observed with water content increase. Slope (b) of the exponential model (fitted to the soil mechanical strength characteristic curve), as an index of hardsetting, had positive correlation with the sand content and negative correlation with the silt content. Overall, texture and calcium carbonate content are major and effective properties in terms of hardsetting phenomenon in Hamadan soils.

---

This study was conducted to assess the long-term effects of soil texture and crop management on transport of lithium (Li+) and bromide (Br-) under unsaturated flow conditions. Treatments were two different soil textures of clay loam and sandy loam to be cropped with either wheat or alfalfa for 4 years. Undisturbed soil columns were taken for the steady-state flow condition using tap water prior to applying a pulse of 0.005 M (C0) LiBr solution as the influent. Four pore volumes (4PV) leaching for each column was obtained. Bromide and lithium concentrations of the effluent (C) were measured in 0.2PV intervals using bromide selective electrode and flame photometer, respectively. Relative concentrations (C/C0) of Br- and Li+ in the effluent were drawn vs. pore volumes. The results showed that the effluent concentrations were significantly affected by crop type and soil texture (in combination by soil structure). The breakthrough curves illustrated the early appearance of Br- in the effluent due to anion repulsion and retarded movement of Li+ because of surface adsorption through the soil columns. Both Br- and Li+ concentrations decreased with time and converged at low levels justifying the minor effect of macropores on continuation of leaching and final transport via soil matrix. The Br- and Li+ concentrations were higher in the effluent of clay loam soil under alfalfa due to higher structural stability compared with sandy loam soil under the same crop. It was also shown that in both soil textures the concentrations of Br- and Li+ appeared to be higher under alfalfa than under wheat, indicating the importance of crop management in contaminant transport compared with soil texture. The trends of breakthrough curves of Li+ were similar to Br- with lower concentration in effluent as a result of its adsorbtion on active surfaces.

---

In this study, the effect of soil structure under saturated and unsaturated flow conditions on nonreactive bromide (BR) transport was investigated. The soil structure treatments consisted of undisturbed columns (prismatic and granular structures), and disturbed columns (single- grain structure). A constant concentration (C0= 0.005 M) of bromide was supplied on the surface of the columns in a steady-state flow condition. For the saturated flow condition, a flux equal to the highest saturated hydraulic conductivity (Ks) of the columns was applied on all of the columns. To create the unsaturated flow condition, a flux equal to the half of the lowest Ks of the columns was imposed on all of the columns. The leaching of the columns was followed for five pore volumes (5PV) and the bromide concentration of the effluent was measured at 0.2PV intervals using bromide selective electrode. The breakthrough curve (BTC) of single- grain structure was sigmoidal (S-shaped) and similar to piston-capillry flow form. In contrast, BTCs of the granular and prismatic structures had a steep initial part and later gradual tailed part. The preferential pathways caused the early appearance of bromide in the leachate of columns of these two structures. Tailing of the BTCs might be due to dispersion and diffusion between mobile and immobile water fractions. In saturated condition, the bromide plume appeared earlier than that in the unsaturated condition because of domination of mass flow and rapid macroporous stream. The results demonstrated the importance of soil structure, preferential pathways, and flow conditions in solute and pollutant transport.

---

Soil aggregate stability is considered as a key indicator of soil quality and health assessments in rangelands. Many factors and properties such as soil texture, organic carbon, calcium carbonate, sodium adsorption ratio, and electrical conductivity might affect soil aggregate stability. The effects of these factors on aggregate stability of 71 soil samples collected from 4 rangeland sites (2 in semi-arid and 2 in arid lands) in Isfahan province were investigated. Aggregate stability was measured using the wet-sieving method. To optimize the trial conditions for the investigated soils, three shaking times (5, 10 and 15 minutes) were used to impose different hydromechanical stresses on the aggregates of ten soils selected out of the studied soils. The structural stability was assessed using mean weight diameter (MWD) and geometric mean diameter (GMD) of the water-stable aggregates. Significant differences of MWD were observed between the shaking times. The 10-min shaking was selected as best for structural stability assessment in the studied regions because it resulted in better differentiation of soils on the basis of structural stability. Among the intrinsic properties, soil organic carbon content had the most important role in aggregate stability in all zones. However, electrical conductivity (in addition to organic carbon content) had an important role in aggregate stability in the arid rangelands. Log-normal distribution and GMD could represent better the aggregate size distribution when compared with normal distribution and MWD in the studied regions. Overall, wet-sieving method with shaking time of 10 min is suggested to assess the soil structural stability in rangelands of Isfahan province. Therefore, soil aggregate stability and the factors affecting this vital indicator can be used efficiently for assessing and monitoring management effectiveness and rangeland functionality trend.

---

Considering soil compaction problem in sugarcane fields due to using heavy harvester and haulout equipment under unsuitable moisture conditions, this research aims to assess soil compaction in sugarcane fields located in Da'balKhazaei Plantation unitofSugarcane Development and By-product Company, Ahvaz. Undisturbed soil samples from the furrow (wheel tracks) were collected for measuring soil water content and bulk density. Considering the changes in soil texture of sugarcane fields, for expressing the degree of soilcompactness, in addition to soil bulk density (BD), relative bulk density (BD divided by reference BD) was also determined. The change in soil mechanical resistance with depth was determined by a cone penetrometer. Results showed that most of soil BD values measured in the sugarcane fields were in the range of small root development scale (high limitation). Comparingthe calculated RBD values with optimum value (0.85), it was observed that most of the values were higher than the optimum values recommended for root growth. This shows excessivesoil compaction in the sugarcane fields. The values of cone indices measured in soil profiles indicated that most of the values were higher than either limiting (2 MPa) or critical (3 MPa) values for root growth. Therefore, for improving soil physical fertility and achieving sustainability in crop production, management of farm machinery traffic in sugarcane fields, especially at the harvest time, needs to be reconsidered.

---

Arbuscular mycorrhizal fungi (AMF) are widespread endosymbionts in terrestrial ecosystems and their exudates have important effects on soil properties. A greenhouse experiment was conducted with six AMF treatments including four exotic species inoculums (Funneliformis mosseae ,Claroideoglomus claroideum  and Rhizophagus irregularis and a mixed isolate of three species), one mixed native AMF species treatment and a sterilized soil (control) with four salinity levels (1, 5, 10 and 15 dS m^-1). AMF increased the soil (EEG) and total (TG) extractable glomalin, and also the hot water (HWC) and diluted acid (DAC) extractable carbohydrates compared to control treatment in all salinity levels. The native AMF species had the greatest effects on EEG, TG, HWC and DAC at 10 and 15 dS m^-1. Soil EEG and TG concentrations were higher in the mixed exotic AMF treatment than in each AMF species. The greatest glomalin concentration was related to F. mosseae at 1, 5 and 15 dS m^-1 but at 10 dS m^-1 the greatest glomalin concentration was related to C. claroideum. The greatest carbohydrate concentration was related to F. mosseae at 1 and 5 dS m^-1 but at 15 dS m^-1 significant differences were observed among the three AMF species. Our results showed that there is an interaction between salinity and different AMF species, and a combination of them determines the function of AMF.

---

Petroleum pollution is an important environmental issue in most of the countries especially those have an oil industry. This study was conducted to investigate the effect of petroleum pollution on soil water repellency and its relation to soil structural stability in Bakhtiardasht area, Isfahan. Polluted and adjacent non-polluted locations were selected to be representative in the green space around the Isfahan Oil Refinery. Soil water repellency was assessed using water drop penetration time (WDPT) in the polluted locations. Soil sample with least aggregates disturbance were collected and selected soil physical and chemical properties were measured. Soil structural stability was evaluated using the wet-sieving method and mechanically dispersible clay (MDC) structural stability indices of mean weight diameter (MWD) and geometric weight diameter (GMD) of aggregates and MDC were then calculated. Results showed that the positive effect of petroleum pollution on the MWD and GMD become significant. Negative impact of petroleum pollution on MDC was also significant. Increment of total petroleum hydrocarbons (TPHs) increased the soil water repellency. A positive correlation was observed between soil water repellency and GMD. However, TPHs concentrations greater than 6.4% decreased the MWD and GMD presumably due to anionic repulsion between clay particles and hydrocarbon functional groups. Although greater water repellency increased soil structural stability in the polluted locations when compared to control locations, however, diminished water retention of polluted soil has created an unfavorable condition for the green space in the area.

---

Today, modern irrigation systems are constructed at a very high cost to operate for optimal use of water and soil. Lack of appropriate technical, social and economic studies, caused high maintenance costs of these facilities during operation. Water resources have been polluted due to industrial development, increasing human population and non-compliance with environmental standards. Most of hydraulic structures are built in areas with poor water quality. Furthermore, engineering properties of fine-grained soils, especially the clay soils, depend on factors such as salinity of solute in the pore water. So that any change in salinity of solute leads to change in the physical and mechanical properties of soils, and consequently make damage to hydraulic structure. This study investigated the effect of water salinity on engineering properties of fine-grained soils. For this purpose, NaCl, with 5 different levels (0, 0.1, 0.2, 0.41 and 0.72 mol/L) was added to the soil and the mechanical properties of soil including compaction, shear parameters, Atterberg limits and consolidation parameters were investigated. The results showed that the addition of NaCl had made no significant changes to the maximum dry unit weight and optimum moisture content of the soil, but it reduced cohesion of soil and increased the internal friction angle .Also, Limit Liquid (LL) are decreased, but it had little effect on the Plastic Limit(PL) of soil.
 

---

Soil water repellency can affect several soil properties such as aggregate stability. Soil texture and organic matter are two main internal factors responsible for the variability of soil water repellency. Major sources of organic matter in soil include plant residues, and exudates of plant roots and soil microorganisms. Tall fescue (Festuca arundinacea Schreb.) as an important cool-season perennial forage grass is usually infected by a fungal endophyte (Epichloë coenophiala) which often enhances resistance to biotic and abiotic stresses as well as altering the litter decomposition rate and soil properties. In this study, the effects of endophyte-infected (E+) and endophyte-free (E−) tall fescue residues (in three different levels of 0, 1 and 2%) on soil organic carbon, basal microbial respiration, water-dispersible clay and water repellency index (determined by intrinsic sorptivity method) were investigated in four texturally-different soils in the laboratory. E+ and E− tall fescue residues were completely mixed with moist soil samples and then were incubated at 25 °C. During two months of incubation period, the amended soil samples were subjected to 10 wetting and drying cycles and then, the above-mentioned soil properties were measured. The results indicated that soil organic carbon and water-dispersible clay were greater, while basal soil respiration and repellency index were lower in fine-textured soils. Water repellency index was increased by production of hydrophobic substances (for the rate of 1%) and was reduced by induced greater soil porosity (for the rate of 2%). Presence of endophyte in plant residues had no significant effect on water sorptivity, ethanol sorptivity and water repellency index; nevertheless, E+ residues increased soil organic carbon and decreased water-dispersible clay significantly. Overall, it is concluded that tall fescue residues, especially those with E+, can improve soil physical quality due to improving soil organic carbon storage and water repellency index and decreasing water-dispersible clay (as an index for aggregate instability). These E+ species and the residues have great potential to be used in sustainable soil conservational managements.
 

---

---

---

---

---

---

---