Showing 34 results for Jalalian
H. Majdi, M. Karimian- Eghbal, H. R. Karimzadeh, A. Jalalian,
Volume 10, Issue 3 (fall 2006)
Abstract
Stabilizng sand dunes has been one of the main challenges in the arid regions. So far, different kinds of mulches have been used extensively for sand dune stabilization. This study was carried out to determine the optimum composition, concentration and thickness of clay mulch for sand dune stabilization. For this purpose two soil samples from clay flats of a playa with different amount of salinity from Ardestan area were used to make clay mulches. A sand dune sample was selected as bed for applying the mulch. To select the right ingredient and treatments, clay samples were mixed with sand and different amount of water, and sprayed on sand dune bed. In addition, wheat straw was added to some mixture to test its effect on stability of the mulch. Treatments with lowest crack and highest penetration of mulch in sand bed were selected for the experiment in this study. Mulch treatments contained (1): 250g sand dune + 250g clay + 25g straw (2) 250g clay + 25g straw (3) 250g sand + 250g clay (4) 250g clay (5) 125g sand + 125g clay and (6) 125g clay. All treatments were mixed with 500ml water. The experimental design was a CRD with a 6(mulch) * 2(thickness)* 2 EC factorial method with 3 replications. The results showed that clay mulch were resistant to wind erosion, but erosion took place when they had been bombarded with sandblast. The mulches with straw showed the highest resistance to erosion as compared to other treatments. With increasing the number of mulch layers, resistant to erosion also increased. The added stability of mulch was due to the increase in mulch thickness and also increases in clay and silt content. The overall result of this study shows that the mulch with two layers and higher mixture of clay and sands was the best treatment for the stabilization of sand dunes.
A. Jalalian, J. Givi, M. Bazgir, Sh. Ayoubi,
Volume 10, Issue 4 (winter 2007)
Abstract
In Iran, the development of cultivated areas becomes gradually impossible due to ever-increasing population growth and urban area development. Therefore, it is very important to use the existing cultivated lands more efficiently. Land suitability evaluation makes the sustainable use of the lands feasible. The objective of this study was qualitative, quantitative and economic assessment of land suitability in Talandahst area for rainfed wheat, barley and chickpea. Talandasht plain with a surface area of 4500 ha is located southwest of Kermanshah city. The climate is semi-arid with cold winter and moderate summer. The successive stages of this research included soil survey in the field, soil analysis, qualitative and quantitative and economic evaluations of land suitability. In qualitative evaluation of land, climatic, topographic and soil suitability classes were determined according to the degree of the matching. Limitation and parametric methods were used in qualitative evaluation. Quantitative and economic evaluations made based on the observed yield and gross benefit, respectively. Based on qualitative evaluation, the studied area is marginally suitable for rainfed farming of wheat, barley and chickpea. This is due to water deficiency occurring during some stages of the growing cycle. The solution for this problem is supplementary irrigation. In addition to climate limitation, there are also topographic and soil restriction for the growth of the studied crops. On the basis of observed yield, the land units are moderately to highly suitable for rainfed wheat and barley production. Among the three named crops, the most and least profitable ones are chickpea and barley, respectively, and wheat ranks between them.
M. Yousefifard, A. Jalalian, H. Khademi,
Volume 11, Issue 40 (summer 2007)
Abstract
Improper use of natural resources, especially soil, causes its degradation and severe soil erosion. Water erosion is an important factor causing soil degradation. Land use change of pasture would result in severe soil erosion mainly due to the reduction of vegetation cover and also surface soil disturbance. The objectives of this study were to estimate the amount of sediment, runoff and nutrient loss in four different land uses including a pasture with good vegetation cover (> 20%), a pasture with poor vegetation cover (< 10%), a currently being used dryland farm and a degraded dryland farm which is not used. Soil samples were taken from the depth of 0–10 cm in a completely randomized design with four replications. A rainfall simulator was run for two hours to estimate the amount of sediment, runoff and nutrient loss. Organic matter, total N, available P and distribution of particles size in soil and sediment were measured. The results showed that a very high degradation has occurred in the area mostly due to water erosion created as a result of overgrazing in pasture, susceptibility of geological formations and more importantly, the change of land use pasture to inefficient dryland farming. Maximum and minimum runoff was observed in the abandoned dry landfarm and pasture with good vegetation cover, respectively. Maximum sediment content was observed in dryland farm. Sediment content in dryland farm, abandoned dry landfarm and pasture with poor vegetation cover were 54.5, 21 and 10.4 times more than that in the pasture with good vegetation cover, respectively. Enrichment ratio (ER) of soil particles in sediment was highest for fine silt (2-5µm), followed by clay. A minimum of ER was obtained for sand fraction. Percentages of organic matter, total N and available P in sediment were higher in the first hour as compared to the second one. This is mainly due to the fact that fine particles are removed at the beginnings of the rainfall event. Total removal of these chemical factors was highest in dryland, intermediate in pasture with poor vegetation cover and abandoned dryland and lowest in pasture with good vegetation cover. In general, cultivation and disturbance of the pasture in the area land have caused a great decrease in soil quality and made the surface very sensitive to erosion.
F. Kiani, A. Jalalian, A. Pashaee, H. Khademi,
Volume 11, Issue 41 (fall 2007)
Abstract
To investigate the degree of forest degradation and the effect of land use change on selected soil quality attributes in loess-derived landforms, samples were taken from different land uses including forest, rangeland, degradated rangeland and farmland in Pasang watershed located in the Galikesh area of Golestan province (37°16'N, 55°30'E). The annual average temperature and mean precipitation of study area were 15°C and 730 mm respectively. Organic matter, pH, EC, CaCO3 and nutrients (N, P, K) as chemical indicators, hydraulic conductivity, bulk density and porosity as physical indicators and soil respiration as biological indicator were measured. The results showed that the amount of organic matter decreased three percent when it was turned from forest to farmland, and increased two percent from farmland to rangeland. The amount of CaCO3 in surface layer of deforested area was more than in the forest soils. The amount of soil N in forest and soil P and K in rangeland were higher than in other land uses. Bulk density and porosity in forest and MWD in rangeland were higher than in other land uses because of the decrease in organic matter due to farming activities. Soil respiration in forest was highest as compared to in other land uses. Difference of enzymes activities (L-asparaginase and Dehydrogenase) compared to microbial respiration indicates that enzymes activity is related to specific biological processes while soil microbial respiration basically depends on the general activity of soil microbial population. It could be concluded that amount of organic matter, soil N, bulk density, porosity, MWD, soil respiration and enzymes activities are suitable indicators for soil quality evaluation in this area.
A. Jalalian, M. Amirpour Robat, B. Ghorbani, S.h. Ayoubi,
Volume 11, Issue 42 (winter 2008)
Abstract
Soil erosion is one of the most threatening issues for crop production and environmental qualities, especially for soil and water resources. Appropriate knowledge about total soil loss and runoff is valuable in order to perform soil and water conservation practices in watersheds. EUROSEM, "a single event, dynamic and distributed model," was developed to simulate soil loss, sediment transportation and deposition by rill and interrill processes. This study was conducted to evaluate EUROSEM model in order to simulate soil loss and runoff in Sulijan sub-basin, which covered 20 ha, from Charmah-Bakhtari province. The sub-basin was divided in to 19 homogeneous elements using topographic, land use, plant cover, slope and channel properties throughout it. Soil, plant cover, land surface and climate characteristics were measured and evaluated by field observations and laboratory measurements. Actual soil loss and runoff for studied events were determined by direct measurement in the field. After sensitivity analysis, calibration and validation steps were carried out to simulate runoff and soil loss. The results of sensitivity analysis showed that the EUROSEM model for predicting runoff was more sensitive to hydraulic conductivity, capillary drive and initial soil moisture. On the other hand the model for predicting soil loss was more sensitive to Manning's coefficient and soil cohesion. The results showed that the EUROSEM model was able to simulate well the total runoff, peak of runoff discharge, total soil loss and time for the peak of soil loss discharge. But that could not simulate well the peak of soil loss discharge and time for the peak of runoff. Although it seems that EUROSEM is able to predict soil loss and runoff partially well in individual events, it is necessary to evaluate the efficiency of the models for different basins with varieties of soil, plant cover and climatic properties.
A. Jalalian, M. Rostaminia, S.h. Ayoubi, A.m. Amini,
Volume 11, Issue 42 (winter 2008)
Abstract
Extension of cultivation areas becomes gradually impossible due to ever-increasing population growth and urban area development in Iran. Therefore, it is very important to use the existing cultivated lands more efficiently. Land suitability evaluation makes the sustainable use of the lands feasible. The objective of this study was qualitative, quantitative and economic suitability evaluation of irrigated croplands for wheat, maize and sesame in Mehran plain, Ilam Province. Soil survey in the field, laboratory analysis of the soil samples, qualitative, quantitative and economic evaluation were different successive stages of this research. In qualitative evaluation, climatic, topographic and soil suitability classes were determined according to the degree of the matching with plant requirements, by parametric (square root) method. Quantitative and economic evaluations were done based on observed, potential and marginal yield analysis. Results of the qualitative land evaluation showed that most of the land units were classified moderately suitable for given crops because of soil limitations. Qualitatively, most of the land units were classified in the same classes as, or in lower classes than quantitative suitability classes for wheat and maize production, due to high management level at the farms. Whereas quantitative classes of sesame were determined lower than qualitative classes induced by low management level for this crop. Economic land suitability classification showed that the wheat production was the most economic land utilization type. Results of the economic assessment suggested that the cultivation of wheat in rotation with sesame would produce the most income for different units and could be increased in future using improvement in management level in the study area for sesame cultivation.
N. Toomanian, H. Khademi , A. Jalalian,
Volume 12, Issue 44 (summer 2008)
Abstract
Determination of landscape evolution is useful to well understand the physical environment and it also enables us to conduct the soil related studies. The objective of this study was to establish the historic evolution of Zayandeh-rud Valley from late Tertiary to Quaternary. To achieve this objective, the spatial structure of a representative area of Zayandeh-rud Valley in three dimensions was examined. Responsible geologic and geomorphic processes of landscape formation were determined and inherited records and evidences of changes in soil development were investigated. The inherited foot marks and different analyses proved that following the Zayandeh-rud River formation, from Miocene to present time, the following processes and events have occurred during valley formation pathway: 1- formation of old gypsiferous gravelly alluviums, 2- lagoon formation, the change in the river pathway, 3- playa formation, 4- river terrace deposition and 5- starting of wind erosion.
A. Karimi, H. Khademi, A. Jalalian,
Volume 12, Issue 44 (summer 2008)
Abstract
Despite the existence of highly silty soils in southern Mashhad, there is no information about the aeolian and /or in situ formation of these soils. The main objective of this study was to determine the source of silt generation in this area. Granitic hilly lands in southern Mashhad have been covered by silty deposits. Based on the soil origin, four profiles including a residual soil covered by a silty layer, a residual soil with low amount of silt, a highly silty soil and an alluvial soil as well as a deep profile containing a succession of silty and alluvial materials were studied. Cumulative particle size distribution curve (CPSDC), depth distribution curves of silt/sand ratio (Si/S), Folk inclusive graphic standard deviation, Folk inclusive graphic skewness (SKI) and sand grain morphology analyzed by scanning electron microscopy (SEM) were determined and used to identify the source of the silty materials. Based on the results obtained, silty (L), residual-silty (R-L), residual (R), alluvial (A) and alluvial-silty (A-L) horizons were identified. CPSDC of L horizons is sigmoidal in shape and is easily distinguishable from that of the other horizons. In contrast, the CPSDC of alluvial and residual horizons is spherical in shape. CPSDCs for R-L and A-L horizons are neither sigmoidal nor spherical, but something in between. The L horizons have the highest SKI (very skewed to fine particles) and the lowest Folk inclusive graphic standard deviation (very badly sorted). In this regard, alluvial and residual horizons are intermediate. Because of the silt addition to R-L and A-L horizons, these horizons have a nearly zero SKI (symmetrical) and the highest Folk inclusive graphic standard deviation (very badly sorted). Particle size distribution histograms of R-L and A-L horizons are bimodal, a mode for sand and a mode for silt, suggesting two different sources. Depth distribution of Si/S, SKI and Folk inclusive graphic standard deviation of highly silty and other horizonz show a drastic change between L horizons and the other horizons-an indication of lithologic discontinuity and difference in origin. In conclusion, despite the possible contribution of granitic parent rocks to silt generation in the area, loess deposits recognized appear to have mostly been transported by aeolian movement.
M Momeni, M Kalbasi, A Jalalian, H Khademi,
Volume 12, Issue 46 (1-2009)
Abstract
The forms and dynamics of soil phosphorus can be greatly affected by land use changes, which often involve changes in vegetation cover, biomass production and nutrient cycling in the ecosystem. Present research evaluates the impact of land use change on the amount of total organic and inorganic P, labile, moderately labile and nonlabile P pools in semiarid soils of central Zagros. Samples were collected from surface soils (0-10 cm) of i) of moderately degraded pasture (20-25% plant cover), ii) highly degraded pasture (5-10 % plant cover), and iii) cultivated field (10 years) in Soolegan sub watershed and i) moderately degraded pasture (25-30 % plant cover) and ii) highly degraded pasture (5-10 % plant cover) in Sadat Abad sub-watershed. Significantly (P<0.05) low amounts of total organic P were found following cultivation (23.9%) and overgrazing (18.2 and 40.8 %) in Soolegan and Sadat Abad, respectively. The largest depletion of labile organic P (NaHCO3-Po) (72.3%) and moderately labile organic P (H2SO4-Po plus NaOH-Pi) (24.3%) were observed in cultivated rainfed land in Soolegan. Overgrazing led to decrease in labile organic P (42.1 and 64.4%), moderately labile organic P (13.9 and 35.7%) and nonlabile organic P (NaOH-Po) including moderately resistant and resistant organic P (12.9 and 44.4%) in Soolegan and Sadat Abad, respectively. Our results showed that degradation of natural plant cover cause to depletion in the soil P pools. Decreasing the amounts of moderately resistant and resistant P pools led to a decline in soil productivity and fertility.
M Noruzi, A Jalalian, Sh Ayoubi, H Khademi,
Volume 12, Issue 46 (1-2009)
Abstract
Crop yield, soil properties and erosion are strongly affected by terrain parameters. Therefore, knowledge about the effects of terrain parameters on strategic crops such as wheat production will help us with sustainable management of landscape. This study was conducted in 900ha, of Ardal district, Charmahal and Bakhtiari Province to develop regression models on wheat yield components vs. terrain parameters. Wheat yield and its components were measured in 100 points. Points were distributed randomly in stratified geomorphic surfaces. Yield components were measured by harvesting of 1 m2 plots. Terrain parameters were calculated by a 3×3 m spacing from digital elevation model. The result of descriptive statistics showed that all variables followed a normal distribution. The highest and lowest coefficient of variance (CV) was related to grain yield (0.36) and thousand seeds weight (0.13), respectively. Multiple regression models were established between yield components and terrain parameters attributes. The predictive models were validated using validation data set (20% of all data). The regression analysis revealed that wetness index and curvature were the most important attributes which explained about 45-78% of total yield components variability within the study area. The overall results indicated that topographic attributes may control a significant variability of rain-fed wheat yield. The result of validation analysis confirmed the above-stated conclusion with low RMSE and ME measures.
M Nael , A Jalalian1 , H Khademi, M Kalbasi, F Sotohian, R Schulin,
Volume 14, Issue 51 (spring 2010)
Abstract
Geologic and pedologic controls are the main factors determining the behavior of elements in natural soil environments. In order to assess the role of these factors on content and distribution of selected major and trace elements in soil, six parent materials including: phyllite, tonalite, periditite, dolerite, shale and limestone were selected in Fuman-Masule region. Soil genesis and development of representive residual pedons were studied for each parent material and the total content of Si, Al, Ca, Mg, Fe, Ti, Mn, Ni, Co, Cr, Cu, Pb, V and Zn were compared among them. Enrichment/depletion patters of trace elements were assessed using Ti as reference element. Generally, Cr, Ni, Co and V are highest in soils derived from peridotite (984, 285, 53 and 204 mg/kg, respectively) and dolerite (1023, 176, 39 and 185 mg/kg, respectively). In the same way, Si and Al exhibit the features of parent materials in the sense that the lowest content was observed in soils developed on peridotite, dolerite and limestone. Zinc and Pb are highest in soils derived from shale (106 and 27 mg/kg, respectively). In a given pedon, different elements exhibited different enrichment/depletion patterns moreover, a given element may behave differently not only in soils with different parent materials but also, in some cases, in soils developed on similar lithology. Lead, Zn, Cu and Mn have been generally enriched in most pedons, except in some acidic and strongly leached soils, whereas Co, Cr, Fe, Ni and V have been leached, especially from Dystrudepts and Eutrudepts. The latter elements, however, showed enrichment trend in Hapludalfs and Argiudolls parallel to the development of illuvial B horizons.
M. Nael , A. Jalalian , H. Khademi , M. Kalbasi , F. Sotohian , R. Schulin ,
Volume 14, Issue 54 (winter 2011)
Abstract
Geologic and pedologic controls are the main factors determining the distribution of elements in natural soil environments. In order to assess the role of these factors in the content and distribution of major elements of soil, six parent materials including phyllite (Ph), tonalite (To), periditite (Pe), dolerite (Do), shale (Sh) and limestone (Li) were selected in Fuman-Masule region. Soil genesis and development of representive residual pedons were studied for each parent material. Total content of Si, Al, Ca, Mg, Fe, Mn, K, Na, Ti and P of soil horizons were measured and compared to the geochemical and mineralogical composition of parent materials. Maximum concentrations of Fe2O3 and MgO were found in the soils derived from Pe and Do however, these soils had low content of SiO2 and Al2O3, which is in conformity with the geochemical composition of the parent rocks. On the contrary, FeCBD content of these soils was lowest, indicating the low degree of soil development and, by the same fact, the importance of inheritance factor in soil Fe concentration. However, comparison of total Fe and FeCBD in Li1, Sh2 and To2 revealed that relative development of these pedons is higher than the others. Silicon depletion in Ph1, To2 and Sh2 pedons, relative to parent rocks, is higher than in Pe and Do pedons. However, this element is enriched in Li pedons. MnO content of Pe and Do pedons is governed by geogenic factors, while in Sh pedons, pedogenic factors, especially redox conditions, play the major role. Exchangeable forms of Ca and Na are determined by soil properties rather than by parent material type. Notwithstanding the redistribution of all major elements throughout pedons due to soil forming processes, the importance of inheritance factor in soil Si, Al, Mg, Fe, K, and Ti is higher than pedogenic factors.
M. Hamidpour, A. Jalalian, M. Afyuni, B. Ghorbani,
Volume 16, Issue 62 (Winte - 2013 2013)
Abstract
Models are helpful tools to predict runoff, sediment and soil erosion in watershed conservation practices. The objectives of this research were to investigate sensitivity analysis, calibration and validation of EUROSEM model in estimation of runoff in Tangh-e-Ravagh sub-basin of Karoun watershed. The model was tested in a one hectare experimental test site. The area was divided into nine elements according to EUROSEM user's manual. A triangular weir was installed at the outlet of the area to collect runoff in specified time periods for six rainfall events. Sensitivity analysis of the model was performed by a ±10% change in the dynamic parameters of the model and examining the outputs for a rainstorm. Sensitivity analysis showed that total runoff was sensitive to saturated hydraulic conductivity and insensitive to soil cohesion. Sensitivity analysis indicated that the model sensitivity depends on evaluation conditions and it is site-specific in nature. Calibration and validation of the model was performed on input parameters. Calibration of hydrographs was performed by decreasing saturated hydraulic conductivity and capillary drive and increasing initial soil moisture. Validation results showed that EUROSEM model simulated well the total runoff and peak of runoff discharge, but it could not simulate well the time of runoff, time to peak discharge
B. Khalili Moghadam, M. Afyuni, A. Jalalian, K. C. Abbaspour, A. A. Dehghani,
Volume 19, Issue 71 (spring 2015)
Abstract
With the advent of advanced geographical informational systems (GIS) and remote sensing technologies in recent years, topographic (elevation, slope, and aspect) and vegetation attributes are routinely available from digital elevation models (DEMs) and normalized difference vegetation index (NDVI) at different spatial (watershed, regional) scales. This study explores the use of topographic and vegetation attributes in addition to soil attributes to develop pedotransfer functions (PTFs) for estimating soil saturated hydraulic conductivity in the rangeland of central Zagros. We investigated the use of artificial neural networks (ANNs) in estimating soil saturated hydraulic conductivity from measured particle size distribution, bulk density, topographic attributes, normalized difference vegetation index (NDVI), soil organic carbon (SOC), and CaCo3 in topsoil and subsoil horizon. Three neural networks structures were used and compared with conventional multiple linear regression analysis. The performances of the models were evaluated using spearman’s correlation coefficient (r) based on the observed and the estimated values and normalized mean square error (NMSE). Topographic and vegetation attributes were found to be the most sensitive variables to estimate soil saturated hydraulic conductivity in the rangeland of central Zagros. Improvements were achieved with neural network (r=0.87) models compared with the conventional multiple linear regression (MLR) model (r=0.69).
N. Shahabinejad, M. Mahmoodabadi, A. Jalalian, E. Chavoshi,
Volume 24, Issue 3 (Fall 2020)
Abstract
Wind erosion is known as one of the most important land degradation aspects, particularly in arid and semi-arid regions. Soil properties, by affecting soil erodibility, can control the wind erosion rate. The aim of this study was to attribute the soil physical and chemical properties to the wind erosion rate for the purpose of determining the most important property. To this aim, wind erosion rates were measured in-situ at 60 points of Kerman province using a portable wind tunnel facility. The results indicated that wind erosion rates varied from 0.03 g m-2 min-1 to 3.41 g m-2 min-1. Threshold wind velocity decreased wind erosion rate following a power function (R2=0.81, P<0.001). Clay and silt particles, shear strength, mean weight diameter (MWD), surface gravel, dry stable aggregates (DSA<0.25mm), soil organic carbon (SOC), calcium carbonate equivalent (CCE) and the concentrations of the soluble Ca2+, K+ and Mg2+ were inversely proportional to the wind erosion rates following nonlinear functions. On the other hand, Wind erosion was significantly enhanced with increasing the sand fraction, soluble Na+, electrical conductivity (EC) and sodium adsorption ratio (SAR). According to the final results, among the studied soil properties, SAR and MWD were s the most effective properties controlling wind erosion in the soils of Kerman province. Therefore, it is recommended to consider suitable conservation practices in order to prevent the sodification and degradation of arid soils.
S. S. Ariapak, A. Jalalian, N. Honarjoo,
Volume 25, Issue 2 (Summer 2021)
Abstract
In this study, spatial-temporal variation of dust deposition rate in the western and eastern half of Tehran and its climatic parameters affecting were studied. At 34 points in the city, dust samples were collected by glass traps from the roof, for twelve months, and the climatic data were obtained and analyzed from relevant organizations. The highest deposition rate is in the western half of the city and its total amount has varied from 54.52 to 121.21 g/m2/y. In both halves of the city, summer has the highest dust deposition rate and its central areas have the highest amount. There were significant positive correlations between dust deposition rate with temperature and medium wind speed, and there were significant negative correlations between dust deposition rate with rainfall and relative humidity in all months, which justifies the high dust deposition rate in the dry seasons of the year. The results of stepwise regression showed that rainfall was the most important factor affecting the dust deposition rate in both halves of the city. The city of Tehran has a special geographical location the presence of mountains like a barrier has prevented dust from leaving the city and the air inlet corridor of Tehran has faced problems due to the expansion of building construction and high-rise building. Other factors affecting the rate of dust deposition in this city, in addition to the distance from the main source of dust production, atmospheric parameters can be mentioned the existence of barren lands around the city, vegetation cover, construction operations, and traffic.
H. Alipour, A. Jalalian, N. Honarjoo, N. Toomanian, F. Sarmadian,
Volume 25, Issue 4 (Winiter 2022)
Abstract
Dust is one of the environmental hazards in arid and semi-arid regions of the world. In some areas, under the influence of human activities, dust is contaminated by heavy metals. In this study, the dust of 10 stations in the Kuhdasht region of Lorestan province in four seasons of spring, summer, autumn, and winter, as well as adjacent surface soils (a total of 40 dust samples and 10 surface soil samples), were sampled and some heavy metals including Zn, Pb, Cd, Ni, Cu, and Mn were analyzed. The results revealed that the amount of Zn in the dust was much higher than the surface soils of the region (800 vs. 85 mg/kg). Contamination factor index calculation indicated that high contamination of Cd and Zn, significant contamination of Ni and Pb, and lack of contamination by Cu and Mn. The annual enrichment factor of Cd (33.9) and Zn (24.6) was very high, Ni (11.3) was significant, Pb (6.4) was moderate, Mn (1) and Cu (0.82) were low. Based on the enrichment factor values, Cd, Zn, and Ni seem to have a human origin, Pb has both human activities and natural origin, and Cu and Mn have an only natural origin.
A.r Modares Nia, M. Mirmohamad Sadeghi, A. Jalalian,
Volume 25, Issue 4 (Winiter 2022)
Abstract
Desertification has become one of the main problems of human societies living in the vicinity of desert areas in recent years. One of the methods that have been considered in recent years and are rapidly expanding in the field of soil mechanics is the Microbial Induced Carbonate Precipitation (MICP). In this method, urea-positive organisms that are naturally present in the soil can stabilize the soil and improve its engineering parameters by using urea and calcium chloride. Recently, attempts have been made to use this method to create a crustal layer on the soil to prevent wind erosion. In the present study, the effect of environmental conditions in deserts such as temperature and sand bombardment on microbial soil treatment has been investigated using this new method. The soil of the Segzi region as one of the main centers of dust in the Isfahan region was studied in this research. Therefore, the improved samples are subjected to regional temperatures which increased the surface layer resistance with increasing temperature. Also, the sandstorm conditions of the region were simulated using three different grain sizes of sand inside the wind tunnel. The results of these experiments showed that stabilized soil could withstand the conditions at wind speeds of 7 and 11 m/s. However, by increasing the wind speed to 14 m/s and the grain size, the crustal layer destroys and increases the wind erosion of the soil. Also, the resistance of the surface layer increased by increasing temperature in the tested samples. This increase in resistance continued up to 24 degrees with a high slope, but from 24 degrees onwards, this slope decreases. Based on the results of this research, it can be said that the microbial improvement method can be used as an alternative method in the future to stabilize desert soils.
E. Javiz, A. Jalalian, M.r. Mosaddeghi, E. Chavoshi, N. Honarjoo,
Volume 26, Issue 4 (Winiter 2023)
Abstract
One of the most significant environmental crises in arid, semi-arid, sub-humid, and even humid regions is the destructive phenomenon of desertification and in the arid and semi-arid regions is wind erosion. These problems exist in large areas of Iran and it is necessary to use an environmentally friendly and economic method to solve this problem. In this study, calcium bentonite clay was used for the first time in Iran and perhaps in the worlds in the critical region of Sajzi, which covers an area of 65 hectares. Experiments were performed on the crusts after one year of mulching with bentonite clay. The results showed that wind erosion has a negative and significant correlation with the mean weight diameter and geometric weight diameter of aggregate, aggregates with diameters greater than 0.25 mm, shear strength, and penetration resistance. On the other hand, the results of the permeability test using double-ring and by three models (Kostiakov, Horton, and Philip) showed that the lowest mean square error (SSE) and the highest coefficient of determination (R2) belonged to the Kostiakov model in the mulch-applied and control samples. This result indicated the superiority of the Kostiakov model compared to Horton and Philip's models. Wind erosion intensity was also measured in situ using a portable wind tunnel at 20 points in the Sajzi region. The findings showed that mulch application has controlled more than 95% of soil erosion.
A.r. Eftekhari, M. Mirmohammad Sadeghi, A. Jalalian,
Volume 27, Issue 2 (Summer 2023)
Abstract
The use of biotechnology-based methods in the field of geotechnical engineering has led to the birth of new knowledge of biogeotechnology and several studies have been conducted using this new knowledge in various geotechnical issues including reducing permeability and increasing shear strength, especially in sandy soils and the desired results have been obtained. Nevertheless, little research has been done using biogeotechnology in the field of improving the mechanical properties of clay soils, especially in reducing the swelling of expansive soils, which is considered one of the types of problematic soils. The main cause of swelling of expansive soils is the presence of montmorillonite clays in these types of soils. Using chemical additives to stabilize expansive soils such as lime and cement is a common practice. However, environmental concerns related to greenhouse gas production caused by the production of chemical substances and the destructive effects of these substances on the environment and soils have encouraged researchers to use other sustainable stabilization alternatives. Microbial Induced Carbonate Precipitation (MICP) is a technique that can be a promising solution to solve this problem. The objective of the present study was to investigate the effect of the MICP method on the swelling of expansive clay soils and its effect on the mechanical strength of this type of soil. One-dimensional swelling tests, uniaxial compressive strength tests, and Atterberg limits tests were performed on clay soil with a liquid limit of 53 using Sporosarcina pasteurii bacteria, calcium chloride, and urea as nutrients. Taguchi's method was used for the design of the experiments and the statistical analysis of the results. This method designs experiments through partial factorial and reduces their number without a significant effect on the results. Bacterial concentration, nutrient molarity ratio, treatment time, and soil moisture were selected as four factors with Four levels of variation. The results showed that the (MICP) method was effective in reducing the swelling potential of expansive soils and also caused a significant increase in the unconfined compressive strength of the soil and its undrained shear strength.