Showing 28 results for shirani
S. Farahi, M. Hamidpour, H. Shirani, H. Dashti, M. Heshmati,
Volume 17, Issue 66 (winter 2014)
Abstract
This research was conducted to study the effect of natural and polyacrylamide-modified montmorillonite on the sorption of Cd from aqueous solutions. The sorption of Cd on the sorbents was studied as a function of pH (Cd concentration: 10 mg L-1) in the range of 4-8.5, and as a function of metal concentration (Cd concentration in the range of 1-10 mgL-1) using a 24h batch equilibration. Experimental and modeling data from equilibrium investigations revealed that the Koble–Corrigan sorption model describes the interaction between Cd and the two sorbents better than the Freundlich and Langmuir models. The values of KF constant of Freundlich and KL constant of Langmuir models were higher for sorption of Cd onto the modified montmorillonite than for those of natural montmorillonite. Maximum sorption capacity calculated from the Langmuir model was 0.6 and 0.7 mg g-1 for natural and modified montmorillonite, respectively. These values are indications of high sorption affinity of Cd to montmorillonite in the presence of polyacrylamide. The amount of Cd sorbed by modified montmorillonite decreased by increasing solution pH while Cd sorption by natural montmorillonite increased by increasing the solution pH.
E. Amiri, A. A. Mahboubi, M. R. Mosaddeghi, H. Shirani,
Volume 18, Issue 68 (summer 2014)
Abstract
In this study, the effect of soil structure under saturated and unsaturated flow conditions on nonreactive bromide (BR) transport was investigated. The soil structure treatments consisted of undisturbed columns (prismatic and granular structures), and disturbed columns (single- grain structure). A constant concentration (C0= 0.005 M) of bromide was supplied on the surface of the columns in a steady-state flow condition. For the saturated flow condition, a flux equal to the highest saturated hydraulic conductivity (Ks) of the columns was applied on all of the columns. To create the unsaturated flow condition, a flux equal to the half of the lowest Ks of the columns was imposed on all of the columns.
The leaching of the columns was followed for five pore volumes (5PV) and the bromide concentration of the effluent was measured at 0.2PV intervals using bromide selective electrode. The breakthrough curve (BTC) of single- grain structure was sigmoidal (S-shaped) and similar to piston-capillry flow form. In contrast, BTCs of the granular and prismatic structures had a steep initial part and later gradual tailed part. The preferential pathways caused the early appearance of bromide in the leachate of columns of these two structures. Tailing of the BTCs might be due to dispersion and diffusion between mobile and immobile water fractions. In saturated condition, the bromide plume appeared earlier than that in the unsaturated condition because of domination of mass flow and rapid macroporous stream. The results demonstrated the importance of soil structure, preferential pathways, and flow conditions in solute and pollutant transport.
H. Karimi, A. Fotovat, A. Lakzian, Gh. H. Haghnia, M. Shirani,
Volume 18, Issue 68 (summer 2014)
Abstract
In recent years, due to the increased population, urbanization and changes in human consumption patterns, urban, industrial and agricultural soils have been exposed to various pollutants such as heavy metals. The objective of this research was to identify hotspots of Pb by using global and local Moran Indices in urban and suburban soils of Kashafrood catchment. A total of 261 surface soil samples (0-15 cm deep) were taken using irregular girding network method and their total Pb concentrations were measured. The positive Moran index at confidence level of more than 99 percent showed the spatial clusters between observations. On the basis of local Moran index results, 15 samples were introduced as hotspots (high-high value) located southeast of Mashhad plain. Exclusion of extreme values resulted in the addition of high-high cluster (hotspots) leading to the extension of these areas to the West of the Mashhad city.
These areas are introduced as hotspots due to the urban land use, the direction of prevailing wind, and the area being close to Mashhad airport.
M. Mosalaei, H. Shirani, V. Mozafari, I. Esfandiarpour,
Volume 18, Issue 70 (winter 2015)
Abstract
Salinity and ions toxicity are one of the main problems of agricultural lands in arid and semi-arid regions, such as Iran. In addition to the salinity problem, some other marks like boron toxicity in crops have been seen in Hossein Abad area as one of the main agricultural regions of Yazd. Therefore, this study intends to evaluate and analyze spatial variability of soil salinity as an aspect of soil degradation, and prepares soil salinity and boron maps. A regular grid sampling scheme was done through a 150 m interval. Salinity and boron were measured at the depth of 0 to 30 cm. Totally 104 samples were measured. After statistical analysis of the data and studying their distribution, Kriging estimator was used for mapping the mentioned variables. Results showed that the region has a salinity problem and does not have any boron toxicity. According to the relationship of nugget effect and sill, there was a strong dependency among all the measured factors except for boron and pH factors. The least salinity was observed in cultivated areas due to the leaching process. The boron range was between 0.07 and 1.6 mg kg-1. Salinity and soil boron were significantly correlated at 99 % confidence level. Based on the Spearman and Pearson tests, there was a positive correlation between SAR and salinity at 99 % confidence level, which shows the region has more sodic salts than others. Also, pH of the region did not present any problem for growing crops.
K. Shirani, A. R. Arabameri,
Volume 19, Issue 72 (summer 2015)
Abstract
This research was conducted to prepare landslide susceptibility zonation (LSZ) map for the Dez-e-Ouliabasin using logistic regression model. For this purpose, at first, the most important factors affecting land sliding including slope, aspect, elevation, precipitation, the distance from road, the distance from fault, the distance from drainage, land use, and lithology were determined. Then, thelandslide inventory mapwas preparedby using field digital checks, GPS and satellite images. In the next step, the landslide susceptibility zonation mapwas preparedby usinglogistic regression method. According to the obtained coefficients for LSZ maps, the most important factor in the study area was elevation layer. The Receiver Operating Curve (ROC) index value was calculated (0.92), which indicates a very high level and suggests thatthe observed mass movements have a strong relationship with the logistic regression model.
S. Molaei, H. Shirani, M. Hamidpour, H. Shekofteh , A. A. Besalatpour,
Volume 19, Issue 74 (Winter 2016)
Abstract
This experiment was conducted to evaluate the effect of vermicompost, pistachio kernel and shrimp shell on the immobilization and availability of Cd, Pb and Zn in corn in polluted soils. Treatments consisted of two levels of pistachio kernel, shrimp shell and vermicompost (5 and 10 % w/w). In control treatment, no amendment was added to the soil. The experiment was carried out as a completely randomized design with 3 replications. Plants grew for two months in the greenhouse. Then, all the plants were harvested and their shoots and roots were separated, washed with distilled water and oven dried at 65 °C to a constant mass. The measured characteristics were dry weight of shoots and roots, leaf area, greenness index, chlorophyll fluorescence, maximal quantum yield of PS photochemistry (Fv/Fm), performance index (PI), and total concentrations of Cd , Pb and Zn in shoots and roots. Results showed that plant growth parameters (dry weight of shoots and roots, leaf area) and photosynthetic characteristics (chlorophyll fluorescence, Fv/Fm, and PI) were higher in plants grown in vermicompost and pistachio kernel treatments as compared to those grown in control. Plants died in shrimp shell treatment after two weeks. The concentration of Cd, Zn and Pb in shoots and roots of plants grown in vermicompost and pistachio kernel treatments were lower than those grown in control.
K. Shirani,
Volume 21, Issue 1 (Spring 2017)
Abstract
Landslide susceptibility mapping is essential for land use planning and decision-making especially in the mountainous areas. The main objective of present research is to produce landslide hazard zonation at Sarkhoun basin in Karoon basin using two statistical models such as an index of Shannon’s entropy and weight of evidence and to assess the obtained results. At the first stage, landslide locations were identified in the study area by interpretation of aerial photographs, image sattellites, and from field investigations and then landslide inventory map was created for study area. The landslide conditioning factors such as slope degree, slope aspect, altitude, lithology, land use,distance of road, distance of fault, distance of drainage, topographic wetness index (TWI), Convergence Index, and precipitation were extracted from the spatial database and they were digitized in GIS environment. With integrated variables, landslides were calculated in each variable class and weighted in index of entropy and weight of evidence model. In the last, landslide hazard zonation map were obtained with both of models. The results of landslide susceptibility mapps of both statistical models were indicated more than 70 percent the occurred landslides were located in very high and high zones that about half of the basin area (over 45 percent) constitute. Also, the results of both models together were revealed that land use, has the greatest impact on the occurred landslides. Resolution of the zones, based on the seed cell area index (SCAI) and frequency ratio (FR) were evaluated suitable for both statistical models. Finally, the ROC (receiver operating characteristic) curves for landslide susceptibility maps were drawn and the areas under the curve (AUC) were calculated. The verification results of both models were evaluated very well and showed that the index of entropy model (AUC=89%) performed slightly better than weight of evidence model (AUC=82%).
A. Arabameri, K. Shirani,
Volume 21, Issue 3 (Fall 2017)
Abstract
Recent urban development and population growth in Shahrood tend to adopt a strategy for ground water management. This project, which is a descriptive- analytic type study based on field observation and laboratory analysis, aims to delineate proper sites for groundwater artificial recharge using integrated AHP-TOPSIS. First, the study area was delineated using remote sensing techniques. Then, appropriate criteria including 5 main criteria and 12 sub-criteria were obtained by field observation and literature review. Then, the appropriate sites for groundwater recharge were determined. The process of the used method consists of designing hierarchical structure of the project, preparation of pairwise comparison matrices, weighting criteria and sub criteria values by experts, and ultimately ranking them by TOPSIS method. Results showed that lithology, slope, water table depth, and land use have the main role in sites delineation. A number of control sites were employed for model validation that indicates 87.20 percent accuracy. Overally, 73.6 and 82.12 percent of the total area were grouped as very suitable and suitable classes, respectively.
F. Heidari, K. Shirani, R. Saboohi,
Volume 21, Issue 3 (Fall 2017)
Abstract
The Ab-Barik watershed in Bam is a part of Lut desert basin. It is like all other desert areas which has erosion problems caused by wind erosion, sand and soil storms. The result of these sand storms appears as continuous and isolated sand hills. In this paper it was attempted to identify direction and source of harvest points by using sedimentological methods. This was accomplished by step by step sand processed method. At the first step the main direction of harvest areas was determined by some studies such as collecting public information, the study of general morphology and measuring sand hill, comparison of aerial photos in different periods and analysis of region winds. At the second step the origin of sand areas was recognized by investigations such as the study of geomorphological facies of lands of harvest regions with emphasis on morphodynamic wind, granulation of sand hills elements and surface soil of erosionic facies plots at harvest lands, study of morphoscopy of forming particles of samples and determination of indices including central diameter, roundness, sorting and mineralogy of samples. The results revealed that the main source of sands is clay pan facies and farm lands, especially waste lands. Also, the main direction of harvest areas displacement is from south, southwest to north, and northeast. Application of results of this study can modify the used management methods, controlling and confronting with the problem of wind erosion and sand and soil storms.
H. Shirani, S. Shirvani, M. Moradie,
Volume 22, Issue 2 (Summer 2018)
Abstract
In recent years, microbial contamination of surface and groundwater is a serious problem in some countries, leading to dangerous diseases. Soil salinity and irrigation water can affect the amount of transport or survival of bacteria in soil. In this study, the effect of different levels of salinity of irrigation water with EC: 0.5, 2.5, 6 ds/m and three manures including poultry manure, cow manure and the mixture of poultry and cow manure with 10 ton ha-1 on the transport of Escherchia coli was investigated in disturbed soil columns with 30cm height and 10cm diameter under unsteady-state water conditions. The concentration of Escherchia coli was measured. The severity of the effluent contamination of the treated columns with water salinity was 6 ds/m, which was less than that with the salinity of 2.5 and 0.5 ds/m. This difference was significant at the 0.01 probability level. Also, the effluent contamination of poultry manure-treated columns was greater than the cow manure and the mixed manure, and the contamination of mixed manure was greater than that of cow manure. The interaction of different salinity treatments on the concentration of Escherchia coli in different fertilizer treatments was significant at the 0.01 probability level. The results showed that the concentration of the released bacteria was affected by irrigation water salinity and with increasing the salinity, the concentration of the bacteria was reduced.
K. Shirani,
Volume 22, Issue 3 (Fall 2018)
Abstract
The persistent scattering interferometry (PSI) technique is a valuable tool in displacements' monitoring of earth's surface. The persistent scattering interferometry (PSI) based on persistent scatterrer (PSInSAR) is one of the techniques used to reduce constraints (temporal and spatial incoherency). It is based on persistent scatterer and monitor displacement of only the pixels with timely-constant properties of scatterer. In order to detect and monitor landslides, two time series SAR data sets including PALSAR ascending images from 2007 to 2010 and ASAR images from 2003 to 2010 with C-band and L-band wavelength were applied, respectively. Also, the PSI technique was implemented in a landslide near Noghol village, Padena, Semirom of Isfahan province. The results revealed that both PALSAR and ASAR data set were efficient in identifying Noghol landslide. The results obtained from ASAR and PALSAR images processing (with the values of 1253 mm and 1578 mm in two stages of time 4 and 7 years, respctively) were compared. The obtained vertical displacement's rate of the landslide by using ASAR data was more suitable because of its descending orbit. However, PALSAR images that indetified more persistent scatterrer points were better in the detection of the landslide area. The results of GPS and PSInSAR techniques revealed that landslide displacement values and aspect were the same, confirming 135 centimeters of displacement to the west aspect. Finally, a combination of radar data in two different passes provided the possibility of monitoring the mechanism of landslide and its movement direction.
K. Shirani, S. Chavoshi,
Volume 22, Issue 4 (Winter 2019)
Abstract
Catchment prioritization in terms of natural disaster intensity as well as prevention and control practices plays a main role in the natural resources and watershed management. In this study, a total of 24 sub-catchments in the Zohreh-Jarrahi basin were prioritized according to their morphometric parameters and using the mixed model of TOPSIS-Multivariate regression. A total of 12 morphometric parameters including constant component of channel maintenance, drainage density, ruggedness number, infiltration index, stream power index, stream frequency, slope, drainage texture rate, relief rate, form factor, bifurcation ratio and topography wetness index, in addition to rainfall, were studied and scored. Parameters were weighted by using multivariate regression and the spatial distribution of the observed flood events. TOPSIS model was used for the prioritization process. The results obtained from the weighting analysis showed that the ruggedness number, slope and rainfall had the highest effect on flooding in the study area with the score of 0.068, 0.024, and 0.016, respectively. According to the prioritization results, sub-catchments of Seidoon, Emamzadeh Jafar, and Takht Deraz, which had the minimum distance to the positive optimum (0.0028, 0.0029, and 0.0029, respectively) and the maximum distance to the negative optimum (0.0097, 0.0098 and 0.0095, respectively), showed the highest flooding intensity with the score of 0.7745, 0.7690 and 0.7625, respectively. In order to validate the results, prioritization results were compared to the observed flood events. Validation results also indicated the efficiency of the mixed model in delineation of catchments prone to flooding. Three sub-catchments of Seidoon, Emamzadeh Jafar and Takht Deraz were observed to have the highest number of observed flood events, thereby showing the high effectiveness of the model and also, the role of the morphometric parameters in flooding.
S. V. Razavi Termeh, K. Shirani, M. Soltani Rabii,
Volume 23, Issue 2 (Summer 2019)
Abstract
Today, supplying water to meet the sustainable development goals is one of the most important concerns and challenges in most countries. Therefore, identification of the areas with groundwater potential is an important tool for conservation, management and exploitation of water resources. The purpose of this research was to prepare the potential groundwater map in Nahavand, Hamedan Province, using the weight of evidence model and combining it with logistic regression. For this purpose, the information layers of slope angle, slope aspect, slope length, altitude, plan curvature, profile curvature, TWI, SPI, distance from fault, fault density, distance from river, drainage density, lithology and land use were identified as the factors affecting groundwater potential and digitized in the ArcGIS software. After designing the groundwater potential map with these three methods, ROCs were used to evaluate the results. Of 273 springs identified in this study, 191 (70%) were used to prepare the groundwater potential map and 82 springs (30%) were used to evaluate the model. The area under curve (AUC) obtained from the ROC curve showed an accuracy of 80.4% for the weight of evidence model and 82.5% for the weight of the evidence- regression combined model
F. Amirimijan, H. Shirani, I. Esfandiarpour, A. Besalatpour, H. Shekofteh,
Volume 23, Issue 3 (Fall 2019)
Abstract
Use of the curve gradient of the Soil Water Retention Curves (SWRC) in the inflection point (S Index) is one of the main indices for assessing the soil quality for management objectives in agricultural and garden lands. In this study Anneling Simulated – artificial neural network (SA-ANN) hybrid algorithm was used to identify the most effective soil features on estimation of S Index in Jiroft plain. For this purpose, 350 disturbed and undisturbed soils samples were collected from the agricultural and garden lands and then some physical and chemical soil properties including Sand, Silt, Clay percent, Electrical Conductivity at saturation, Bulk Density, total porosity, Organic Mater, and percent of equal Calcium Carbonate were measured. Moreover, the soil moisture amount was determined within the suctions of 0, 10, 30, 50, 100, 300, 500, 1000, 1500 KP using pressure plate. Then, the determinant features influencing the modeling of S Index were derived using SA-ANN hybrid algorithm. The results indicated that modeling precision increased by reducing the input variables. According to the sensitivity analysis, the Bulk Density had the highest sensitivity coefficient (sensitivity coefficient=0.5) and was identified as the determinant feature for modeling the S Index. So, since increasing the number of features does not necessarily increase the accuracy of modeling, reducing input features is due to cost reduction and time-consuming research.
M. Moradizadeh, K. Shirani,
Volume 23, Issue 4 (winter 2020)
Abstract
Water resources management depends on the precise assessment of water storage and access in each region, as well as environmental interactions of these resources. The man objective of this study was to delineate the potential zones of groundwater storage using FAHP. Mapping and assessment of it required maps of geomorphology, drainage, density, lineament density, slope and vegetation, which were initially prepared as the input layers in FAHP; the appropriate weights were attributed to them based on FAHP. Potential zones of ground water were classified into five classes of poor, average, good, very good and excellent. The number and density of available wells and springs in the study area dealt with the potential of the region for groundwater storage. So, ROC was used to assess the validation of results, considering spring points as signs of water resources. According to the results, classes of very good, good, average, weak, and very weak were ranked as the first to the last in terms of privilege order with an area of 37.7, 55, 40, 107, and 98.4 square kilometers, respectively.
S. Chavoshi Borujeni, K. Shirani,
Volume 24, Issue 3 (Fall 2020)
Abstract
Selection of the appropriate distribution function and estimation of its parameters are two fundamental steps in the accurate estimation of flood magnitude. This study relied on the concept of optimization by meta heuristic algorithms to improve the results obtained from the conventional methods of parameter estimation, such as maximum likelihood (ML), moments (MOM) and probability weighted moments (PWM) methods. More specifically, this study aimed to improve flood frequency analysis using the Artificial Bee Colony algorithm (ABC). The overall performance of this algorithm was compared to the conventional methods by employing goodness of fit statistics, correlation coefficient (CC), coefficient of efficiency (CE) and root mean square error (RMSE). The study area, Babolrood catchment located in southern bank of Caspian Sea, has been subjected to annual flooding events. A total of 6 hydrometry stations in the study area were delineated and their data were used in the analysis of 6 distribution functions of Normal, Gumbel, Gamma, Pearson Type 3, General Extreme Value and General Logistic. This analysis indicated that Gamma and Pearson Type 3 were the most appropriate distribution functions for flood appraisal in the study area, according to the ABC and conventional methods, respectively. Also, the results showed that ABC outperformed ML, MOM and PWM; so, Gamma could be recommended as the most reliable distribution function for flood frequency analysis in the study area.
K. Shirani, M. Pasandi, B. Ebrahimi,
Volume 25, Issue 1 (Spring 2021)
Abstract
Land subsidence as a hydrogeomorphology event is currently occurring dangerously in many plains of the country due to uncontrolled groundwater extraction from water bearing layers, and accordingly monitoring and studying this phenomenon seems to be necessary. In this study, land subsidence rate of the Najafabad aquifer was determined through the Differential Radar Interferometry (DInSAR) processing of the ASAR and PALSAR radar data and the results were validated by comparying with the differential leveling and groundwater level drowdown data. Processing of the ASAR sensor data estimates the land subsidence in the Najafabad plain at an average annual subsidence rate of 6.7 cm and a total of 41 cm during 6 years period and processing of the PALSAR data suggests an annual rate of 7.7 cm and total subsidence of 30 cm during 4 years period. Most of the occured displacements are related to the Tiranchi, Koushk, Ghahderijan, Goldasht and Falavarjan cities. The simultaneous groundwater level data with acquisition date of the radar satellite images between 2002 and 2014 shows a drawdown ranging from 0.5 to 46.5 meters in the south and east to north of the Najafabad city consistent with the estimated land subsidence areas.The DInSAR processing of the PALSAR data has led to a more accurate results with higher spatial resolution. Results of the radar data processing can be employed for the hazard zonation directly utilized for management and planning of control and preventive measures.
K. Shirani,
Volume 25, Issue 2 (Summer 2021)
Abstract
Delineation of gully erosion susceptible areas by using statistical models, as well as optimum usage of existing data and information with the least time and cost and more precision, is important. The main objective of this study is to determine the areas accuracy to gully erosion and susceptibility mapping by using data mining of the bivariate Dempster-Shafer, linear multivariate statistical methods and their integration in Semirom watershed, southern Isfahan province. First, the geographical location of a total of 156 randomly gullies were mapped using preliminary reports, satellite imagery interpretation and field survey. In the next step, 14 conditioning parameters of the gullies in the study area were selected including the topographic, geomorphometric, environmental, and hydrologic parameters using the regional environmental characteristics and the multicollinearity test for modeling. Then, the Dempster-Shafer statistical, linear regression, and ensembled methods were developed using 70% of the identified gullies and 14 effective parameters as dependent and independent variables, respectively. The remaining 30% of the gully distribution dataset were used for validation. The results of the multivariate regression model showed that land use, slope and distance to drainage network parameters have the most significant relation to gully occurrence. The gully erosion susceptibility maps were prepared by individual and ensemble methods and they were divided to 5 classes of very low to very high rate. The area under the curve (AUC) of the receiver operating characteristic (ROC) curve was used to validate gully erosion susceptibly maps. The verification results showed that the AUC of ensemble method (0.948) is higher than Dempster-Shafer (0.924) and Multivariate regression (0.864) methods. Also, the the seed core area index (SCAI) value of the ensembled model from very low to very high susceptible classes have a decreasing trend that indicating a proper separation of susceptible classes by this model.
K. Shirani, R. Arfania, Y. Fereydoni, R. Naderi Samani, M. Shariati, M. Faizi,
Volume 26, Issue 4 (Winiter 2023)
Abstract
Groundwater is always considered one of the important water resources, especially in arid and semi-arid regions of the world, such as Iran. In recent decades, it has decreased drastically due to excessive use. The objective of this study was to determine the best interpolation method and evaluation of the spatiotemporal variations for the groundwater level in the Sahneh-Biston plain of Kermanshah province during three decades from 1991 to 2020. At first, four Gaussian, linear, spherical, and power semi-variograms were obtained for observations. Then, the best semi-variogram and interpolation methods were selected among the evaluated methods for zoning the groundwater level in the region. The lowest value of the sum of RMSE, MBE, and MAE error criteria and the highest coefficient of determination (R2) between observations and estimates in all three decades and the average of the entire period were calculated and considered to evaluate the most appropriate semi-variogram and interpolation methods for spatial distribution. The results showed that the ordinary kriging method with Gaussian semi-variogram is the best method to estimate the groundwater level in the Sahneh-Biston plain. The average difference between the minimum and maximum groundwater levels based on the observation wells of the study area and the zonation method is from 1279 to 1372 meters and 1289 to 1409 meters during the studied period time, respectively. The groundwater level is placed in more depth with the proximity to the central and southern regions. The maximum decrease and increase of groundwater level variations have been 12 and 19 meters during three decades, respectively. Also, the underground water level variations during these three decades showed that both the second and third decades compared to the first decade and the third decade compared to the second decade have increased in more than 50% of the region. This increase can be caused by the optimum management and water use in these years. Therefore, groundwater level monitoring provides effective help for experts and users in planning and optimal management of groundwater for the sustainable development of water resources.
M. Dehghanian, H. Tabatabaee, H. Shirani, F. Nikookhah,
Volume 27, Issue 1 (Spring 2023)
Abstract
In sustainable agriculture, cow manure is used for greater productivity, a rich source of E-Coli pathogenic bacteria. The objective of this research was to investigate the simultaneous effect of the fractionation size of cattle manure and irrigation water salinity on the retention of E-Coli bacteria in the depths of the sand column with a height of 10 cm under saturated flow. Four different particle fractions of cow manure (1-2, 0.5-1, 0.25-0.5, and smaller than 0.25 mm) were added to the surface of the sand column at the scale of 30 tons per hectare, then leaching was done with different salinities (0, 0.5, 2.5, 5, and 10 dS/m) up to 10 pore volumes, then samples were taken from the depths of 0, 3, 6, and 12 cm. The number of bacteria in each sample was determined by the live counting method. The results showed that the effect of all sources of change and their interaction effects on the retention of bacteria in the soil is significant at the level of 5%. Salinity had a negative effect on the retention of bacteria, and the highest and lowest values of the relative concentration of bacteria (the result of dividing the number of bacteria in each soil depth by the initial number of bacteria in the desired manure treatment) were in 0 dS/m and 10 dS/m salinity of leaching water, respectively. By decreasing the size of cow manure particles due to the increase in hydrophobicity and blocking of preferential pores, the retention of bacteria decreased in all investigated soil depths. The highest and lowest retention of bacteria in the soil were investigated in the largest cow manure particle size (1-2 mm) and the smallest cow manure particle size (less than 0.25 mm), respectively. In addition, the highest relative concentration of bacteria in the soil was seen in the depth of 0-3 cm, and no significant difference was seen in other soil depths.
