Showing 130 results for Char
H. R. Fooladmand, A. R. Sepaskhah, J. Niazi,
Volume 8, Issue 3 (10-2004)
Abstract
To obtain soil-moisture characteristic curve experimentally is time-consuming and usually subject to considerable errors. So, many investigators have tried to predict soil-moisture characteristic curve by different models. One of these models predicts soil moisture characteristic curve based on soil particle size distribution and bulk density. In this model, soil particle size distribution curve is divided into a number of segments, each with a specific particle radius and cumulative particle mass greater than that of the radius. Using these data, soil-moisture characteristic curve was estimated. In this model, a scale factor, α, is used which may be considered as a constant, or obtained by logistic or linear procedures. The average values of α for clay, silty clay, sandy loam, two loam soils, and two silty clay loam soils were 1.159, 1.229, 1.494, 1.391, 1.393, 1.253 and 1.254, respectively. For most conditions, soil particle size distribution curve is not available, but only the percentages of clay, silt, and sand could be obtained using soil textural data, which is not enough to draw a precise soil particle size distribution curve. In this situation, a precise soil particle size distribution curve must be initially developed on the basis of which the soil moisture characteristic curve can be predicted. In this study, using soil textural data of seven different soils, soil moisture characteristic curve of each was estimated. In these estimations, logistic and linear methods were used to obtain the α value. Then, the results were compared with those of measured soil moisture characteristic curve. For estimation of soil particle size distribution curve, two extreme values for soil particle radius, 125 and 999 m, were used. The results indicated that using particle radius of 999 µm is more appropriate. On the other hand, it was found that for clay, silty clay, and sitly clay loam texture, it is more appropriate to employ a linear equation to determine for estimating soil-moisture characteristic curve while the logistic equation can be more appropriately used for loam and sand loam textures.
M. Sharifi, M. Hajabbasi, M. Kalbasi, M. Mobli,
Volume 9, Issue 1 (4-2005)
Abstract
Potato (Solanum tuberosum L.) has relatively weak root system and requires high nitrogen fertilizer which is costly and may pose environmental pollution. This study was conducted to compare root morphological characteristics and nitrogen uptake of some potato cultivars growing in Iran. A greenhouse experiment using a completely randomized design with 3 replications and 8 potato cultivars including: Arinda, Agria, Premiere, Diamant, Concord, Marfona, Marodana and Nevita was conducted at Isfahan University of Technology, Isfahan. Virus-free seed tubers were planted and grown up to flowering stage. The plants were then harvested and their root length (RL), root average diameter (RAD) and root surface area (RSA) were determined using a Delta-T Scan image analysis system and Windias software. Root length density (RLD), root length and shoot weight ratio (R/S) were also calculated. Dry mater production and nitrogen accumulation (total nitrogen uptake) (PNA) were also determined. Soil inorganic nitrogen was measured before planting and after harvest. All measured parameters, except RAD, were significantly (p<0.05) affected by cultivar. Large differences observed between cultivars for all traits indicated genetic diversity among the studied potato cultivars. The highest and the lowest values of RL, RLD, RSA, R/S, RDW and PNA were found in Marfona and Nevita respectively. Based on cluster analysis, cultivars were divided into four different groups. Under the condition of this study, Marfona was superior whereas Arinda, Nevita, Marodana and Agria were inferior. Due to the high differences in root morphological characteristics and nitrogen uptake among potato cultivars, plant breeders may produce cultivars with larger root volumes and high nitrogen uptake.
H. Naghavi, M. A. Hajabbasi, M. Afyuni,
Volume 9, Issue 3 (10-2005)
Abstract
The objective of this study was to evaluate effects of cow manure on soil hydraulic properties and bromide leaching in a sandy loam soil (coarse loamy mixed, Typic Torrifluvents). Manure was applied at 0, 30, and 60 tha-1 at three replications in a completely random design. Three months after manure application potassium bromide (KBr) at rate of 300 Kg ha-1 Br was uniformly applied on the surface. Soil bulk density, porosity, organic matter, and soil moisture at18 levels of matric potentials were determined. Soil samples to the depth of 105 cm at 15-cm increments were collected after 100, 200 and 400 mm of irrigation. Soil bulk density, porosity, organic matter content, and soil moisture at different levels of matric potential increased significantly with manure application. Manure application also significantly affected the hydraulic parameters. Bromide leaching was significantly lower in plots with manure application and the greatest leaching occurred at the zero manure application treatment. The center of mass evaluation indicated a relatively similar result with measured values.
S. M. A. Zomorodian, M. R. Bagheri Sabzevari,
Volume 9, Issue 4 (1-2006)
Abstract
The vertical pipe intake is an economical structure relative to the other alternatives. VPI usually installed near the water surface and prevents from the coarse sediment entrance to the system. The strong vortex in VPI entrance is a major problem which may reduce the system efficiency. Recognizing the vortex affected parameters, helping engineers to design anti vortex structures. In this study an experimental model is built to study the effect of tangential velocity, flow direction at approach channel outlet on the discharge coefficient of vertical pipe intake. By dimensional analysis it is indicated that the vortex in VPI could be defined by the dimensionless numbers (Reynolds, Weber, Froude, Circulation and Submergence). The relationship between the Froude, Circulation and Submergence numbers are presented. By using this relation one can determine the Submergence number and then calculate the discharge coefficient of vertical pipe intake.
L. Rozbeh Nasiraei, Sh. Dokhani, M. Shahedi, R. Shokrani,
Volume 9, Issue 4 (1-2006)
Abstract
The Two cultivars of kiwi fruit, Hayward and Abbot, with the desirable quality were harvested on time from Valiabad, a region in Tonekabon (Mazanddaran Provicnce). Fruits were graded and packed in the wooden boxes, cartons and low density polyethylene (LDPE) films, the fruits were cold stored in a proper and constant conditions (T= ±0.5 & RH=90-95%) for a period of 6 months. Samples were taken in completely randomised design from each package for intervals of 30±3 days and during storage (6 months). Chemical characteristics such as the total soluble solids(TSS), titratable acidity as citric acid, dry matter, vitamin C and the Physical characteristics such as yield point (Y.P.), yield point strength (Y.P.S.), penetration force (P.F.) and penetration stress (P.S.) were measured. Statistical analysis was performed with the factorial experiment in an unequal completely randomized design and the means compaired by Duncan multiple range test. The results indicated that, cv, Abbot has shorter shelf life, 4 months, compared to Hayward with 6 months storage period. Hayward contained more dry matter than Abbot throughout the storage period. Total soluble solids of cultivars increased and titrable acidity as citric acid decreased during storage. Vitamin C of Abbot was more than Hayward throughout the storage. Total factors in relation to texture and physical properties decreased by time such texture Hayward cv.after six month storage and in Abbot after four month storage was softer. As the final conclusion, wooden bins packaging for longer storage and plastic packaging for monotonous rippening of kiwifruit was the best in compared with other packaging.
M. Heidarour, S. F. Mousavi, A. R. Roushani Zarmehri,
Volume 10, Issue 3 (10-2006)
Abstract
Because of slight variation of the static head due to discharge fluctuations, the labyrinth weirs are considered to be economical structures for flood control and water level regulation in irrigation networks, as compared to other devices. Labyrinth weirs are composed of folded sections observed as trapezoidal and triangular in plan view. In this study, rectangular and U-shaped labyrinth weirs were investigated. Experiments were conducted on 15 labyrinth weir models. The models included eight rectangular labyrinth models and six U-shaped labyrinth models with different heights and lengths, and one linear model. All the experiments were performed in a horizontal rectangular flume, 7 m long, 0.32 m wide and 0.35 m high. The results indicated that for all the models, discharge coefficient increased sharply with an increase in Ht/P and attained a maximum value. This coefficient then decreased smoothly with a further increase in Ht/P. Increasing height of weirs increased the discharge coefficient for both rectangular and U-shaped weirs. The results also showed that increasing the length parallel to the flow direction decreased and increasing the length perpendicular to the flow direction increased the discharge coefficient. Generally, the discharge coefficient for rectangular weir was less than that of the U-shaped weir. The obtained results compared with those of Tullis et al. (1995) showed that discharge coefficient for U-shaped weir is more and for rectangular weir is less than that of the trapezoidal weir for angle of the side legs of 8 and 12 degrees.
A. Sarkhosh, Z. Zamani, M. R. Fatahi Moghaddam, A. Ebadi, A. Saie, S. Z. Tabatabaie, M. R. Akrami,
Volume 10, Issue 4 (1-2007)
Abstract
In order to determine the most important quantitative and qualitative characteristics of pomegranate fruit and its components for categorizing the genotypes, a study was carried out using 24 genotypes. In this study 28 quantitative and qualitative characteristics of pomegranate fruit and seed were evaluated. Analysis of variance showed that all of the characteristics in examined genotypes were significant, showing high variability in characteristics. Results of simple correlation analysis showed the existence of significant, positive and negative correlations among some important characteristics. Also, factor analysis showed that most of fruit juice, aril and seed characteristics constituted the main factors. Effective characteristics categorized in seven factors accounted for 89% of total variance. For each factor, eigen value more than 0.7 was considered significant. Cluster analysis was performed using these seven factors and genotypes, in the distance of 9, were divided into 5 main clusters. These groups were mainly distinct in fruit flavor and soft seededness. Furthermore, by using three main factors, genotypes positions determined in 3-plot analysis, which distinguished sweeter genotypes from sweet-sour and sour genotypes.
M. R. Dini Torkamani, J. Karapetion,
Volume 11, Issue 40 (7-2007)
Abstract
Sesame is an annual self-pollinated plant with a high seed oil and protein content. It is considered as an oilseed plant for human consumption. For a breeding purpore, quantitative and qualitative characteristics of seed total protein of different sesame varieties (Oltan, Zoodras , Yekta , Hendi , Varamin , Chini , Karaj 1 , Moghan local,Nazok tak sakheh and Nazok chand shakheh) were evaluated. Protein extracts were analysed using Kejeldal and gel electrophoresis methods. Total average of 24.02% was observed for seed protein content of all varieties. Analysis of varieties revealed a significant variation at (p < 0.01) between varieties. The profile of seed storage proteins had a relative mobility from 0.20 to 0.94. The observed bands varied in intensity and scattered in three zones of the gel . All bands were monomorphic and no variation was observed between the varieties. It was concluded that this characteristic does not carry the necessary value for breeding purposes.
E. Zandi Esfahan, S. J. Khajedin, M. Jafari, H. Karimizadeh, H. Azarnivand,
Volume 11, Issue 40 (7-2007)
Abstract
In order to determine the reciprocal relationship between the important characteristics of soil and the growth of Haloxylon ammodendron (C.A. Mey) plant in segsi plain of Isfahan., ordination method was used. The study was performed through the stratified random sampling and the regions were separated according to the plant age and physical physiognomy, then 10 samples of Haloxylon ammodendron (C.A. Mey) of the same age were selected in each region. Meanwhile, factors such as height, canopy cover area, canopy cover perimeter, canopy cover diameter, and basal area were considered. Also, 30 profiles from viewpoint of growth situations in 10 different regions were dug. Soil characteristics such as : pH, Ec, total soluble Ca2+ and Mg2+, Cl-, CO3--, HCO3-, SP%, CaCO3%, CaSO4%, organic matter%, total nitrogen percentage, phosphorous, Na+, K+, SAR, and hardpan depth were measured. Data was analyzed using ordination method. According to the results, samples of the same age showed significant differences in plant features. Other results showed that physical characteristics such as depth of hardpan from soil surface, SP%, and chemical characteristics such as salinity, alkalinity and total nitrogen had the highest effect on qualities of this kind of plant. In other words, the results mentioned above showed the important role of Haloxylon ammodendron (C.A. Mey) in sharp increase of salinity and alkanity in it's stratum.
H. R. Fooladmand,
Volume 11, Issue 41 (10-2007)
Abstract
Soil particle size distribution and bulk density are used for estimating soil-moisture characteristic curve. In this model, soil particle size distribution curve is divided into a number of segments, each with a specific particle radius and cumulative percentage of the particles greater than that radius. Using these data, soil-moisture characteristic curve is estimated. In the model a scale factor, a , is used which may be considered as a constant, or obtained by logistic or linear procedures. F or most conditions, soil particle size distribution curve is not available, but only the percentages of clay, silt and sand could be obtained using soil textural data. In this situation, at first a precise soil particle size distribution must be developed, based on which the soil-moisture characteristic curve can be predicted. According to the previous studies, using particle radius of 999 µ m is more appropriate than radius 125 µ m. Also, adjusted coefficients for estimating soil particle size distribution curve for radii 1 to 20 µ m was obtained. In this study, using the soil textural data of 19 different soils from UNSODA database, soil-moisture characteristic curve of each was estimated with logistic and linear methods based on initial and adjusted soil particle size distribution estimation. The estimated values were compared with the measured data. The results indicated that for most soils, using the combination of logistic and adjusted particle size distribution estimation procedures is more appropriate than the previous methods.
M. Vafakhah, G.h. Shojaei,
Volume 11, Issue 42 (1-2008)
Abstract
Continuous measurement of river discharge is a hard and expensive task in hydrology. To overcome this problem, the stage readings at hydrometric gauges are permanently taken and the discharge of any time at which the actual discharge is unavailable will be estimated through a relationship between discharge and stage. To study the stage-discharge relations and the capability of long-term data in establishing a permanent stage-discharge relationship, and also to determine the best time to measure the discharge of rivers, a study was conducted at the hydrometric station of the Zayandehrud regulatory dam using data from 1990 to 2003. The data were analyzed using simple regression analysis, the percentage of relative error and factor analysis. The results indicated that the best model to show the stage-discharge relation at the studied station is a power function model. Moreover, the model used for every year can only be used for that year. The results also showed that the most suitable times for the measurement of discharge are July, December and March.
H. Khoshghalb, K. Arzani, M. J. Malakouti, M. Barzegar,
Volume 12, Issue 45 (10-2008)
Abstract
Changes of the main sugars and organic acids content in Asian pear (Pyrus serotina Rehd.) Cultivars ‘KS’9 and ‘KS’13 grown in Tehran were studied from fruit set to maturity. The main sugars and organic acids content in fruits were determined 1 and 2 months before harvest, at the time of harvest and 1, 2 months after harvest time using High Performance Liquid Chromatography (HPLC). Fruits were stored at 2˚C and 80-85% relative humidity (RH). There were significant differences between cultivars and time of fruit harvest in terms of sugars and organic acids content. In both studied cultivars, fructose, glucose and sorbitol increased from the first fruit sampling to one month after harvest (1 to 9% FW) and then decreased. Sucrose content decreased from 2 months before harvest to 2 months after harvest time (3 to 0.75% FW). In both studied cultivars organic acids content increased at the time of pick-up and then decreased. The highest organic acids contents in the studied cultivars were malic and ascorbic acids (345 and 41.1mg 100g-1FW in ‘KS’9 and control, respectively). The relationship between low sugar and organic acid content in fruits showed the highest correlation (0.8 to 1) in both cultivars among low flesh firmness, low total soluble solid (TSS), low dry weight and high internal browning determined in this study. Results indicated that high content of sugars and organic acids in fruit led to delayed internal browning. Asian pears with a low ascorbic acid concentration are probably more susceptible to internal browning. High correlation was observed between high sugars content and high fruit colour.
Gh. A. Akbari, H. Jabbari, J. Daneshian, I. Alahdadi, N. Shahbazian,
Volume 12, Issue 45 (10-2008)
Abstract
In order to investigate the limited irrigation impact on physical characteristics of seed in nine sunflower hybrids, three 3-replicate field experiments RCBC were conducted under three irrigation regimes (irrigation after 60, 120 and 180 mm cumulative evaporation from class A evaporation pan, respectively) at the research field of Seed and Plant Improvement Institute in Karaj, Iran. The results showed that the Maximum length, width and seed diameter were obtained from irrigation after 60 mm cumulative evaporation from pan, and irrigations after 120 and 180 mm evaporation caused to decrease the length by 11% and 16%, width by 21% and 26% and seed diameter by 22% and 28%, respectively. There fore the seed diameter in comparison with width and seed length was most susceptible to limited irrigations levels. The Maximum length was seen in hybrid of A74×R95, and the maximum width, and seed diameter were observed in hybrids of Allstar. Also, A74×R95 under irrigations after 60 and 120 mm evaporation and Azargol under irrigation after 180 mm evaporation had the highest seed weight.
M Khorshid, As Hosseinpur, Sh Oustan,
Volume 12, Issue 46 (1-2009)
Abstract
Organic manures can affect phosphorus (P) sorption characteristics (PSC) and its availability in soils. Information about effect of sewage sludge (SL) on PSC in calcareous soils of Hamadan province is limited. The objective of this research was to study the effect of SL on PSC and available P in 10 calcareous soils. The soil samples were incubated with and without 1.5 % SL for 5 months at field capacity at 25 ±1 סC . After incubation, available P was determined by Olsen method. Furthermore, 2.5 g samples were shaken with 25 mL 0.01 M CaCl2 containing 0 to 30 mg P L-1 as KH2PO4. After equilibration, suspensions were centrifuged and P concentration was determined in clear extracts. The results showed that SL application increased available P. The mean available P value increased by 37.6 %. Available P in untreated and SL-treated soils ranged from 8.1 to 22.1 and 14.8 to 28.0 mg kg-1, respectively. Sorption data in the all samples were well described by Freundlich and linear isotherm, whereas sorption data in all SL-treated soils did not adequately fit to the Langmuir isotherm. The constants of sorption isotherms were lowered by SL application. The mean sorption maxima, binding energy and maximum buffering capacity values decreased by 38.85, 21.34 and 38.90 % respectively. The mean distribution coefficient, Freundlich n and the mean buffering capacity (slope of linear model) values decreased by 21.7, 16.0 and 6.1 %, respectively. The results of this study showed that application of SL decreases standard phosphorus requirement. Moreover PSC results indicated that use of sewage sludge might increase the risk of P transfer to surface water.
R Rajabi-Kanafgourabi, R Ebadi, M Fazilati, S.z Mirhoseini,
Volume 13, Issue 47 (4-2009)
Abstract
The effect of mulberry leaves enrichment with riboflavin in 7, 37, 77 and 127ppm concentrations on larval growth and cocoon characteristics of Bombyx mori L., hybrid 103×104 was studied. Silkworm larvae were fed on fresh mulberry leaves of shin inche nevise enriched with riboflavin once a day. All biological and economical parameters were determined by using standard techniques in sericulture. The results showed that larval weight was greater in 77ppm among treatments on the 7th day of the fifth instar which had 47% increase compared to control. Maximum amount of female cocoon weight and female pupal weight were recorded 1.622g and 1.169g, respectively, in 127ppm while male cocoon weight and pupal weight were greater in 37ppm and recorded to be 1.169g and 0.895g, respectively. Maximum amount of cocoon shell weight and cocoon shell ratio were recorded in 77ppm for male (0.311g and 26.06%) and female (0.318g and 21.46%). Maximum weight of 50 eggs (0.027g) was recorded in 127ppm while high fertility and hatchability was recorded in 77ppm concentration. Effective rate of rearing was maximum in control treatment (72%) with no significant difference compared with other treatments. The overall results showed that riboflavin can be used at 77ppm concentration for the significant increase of cocoon weight, cocoon shell ratio and egg production of silkworm, Bombyx mori L.
M Sh.zeinodin, M Tadyoni, Sh Dokhani, S Soleymanian Zad,
Volume 13, Issue 48 (7-2009)
Abstract
Exo-polysaccharide (EPS) production by some lactic acid bacteria (starter) during fermentation could affect the physical properties of yoghurt. In this study, at first EPS content and its effects on physical properties of three traditional (S1, S2 and G) and one industrial (I) yoghurt samples were studied. The results showed that there was significant differences in fat content, solid non-fat content, pH, EPS content, viscosity, elasticity and sensitivity to syneresis among samples. Statistical analysis based on a completely randomized design revealed that a significant correlation exists between EPS content and viscosity as well as resistance to syneresis of the samples. Fat content and solid non-fat content of the samples showed no correlation with physical properties of the samples. In the second phase of the study, to remove effects of raw milk composition and to be able to attribute the results to the EPS producing activity of the starter, skim milk was used to produce yoghurt samples using yoghurt samples tested in the first stage only as sources of starter. In these yoghurt samples, there were significant differences between amount of EPS and physical properties of yoghurts. There was also a significant correlation between EPS content and physical properties of each sample.
N Vahedi, M Mazaheri Tehrani, F Shahidi,
Volume 13, Issue 48 (7-2009)
Abstract
In this study, the effect of “Osmodehydrofrozen” fruit addition on sensory, physical, chemical and microbiological properties of concentrated yoghurt and its quality during storage was evaluated. This research was done in two stages. At the first stage, fruit percentage, type and addition time (before and after fermentation) was determined. The results indicated yoghurts containing 10% apple or 13% strawberry, which was added before fermentation had a better quality. Because of high osmotic activity of apple, the synersis was lower in apple yoghurt in comparison with strawberry yoghurt. According to osmotic activity of both fruits, the synersis value was much lower than that of fruit yoghurts, which contained untreated fruits. Taste value was higher in strawberry yoghurt and texture and mouth feel values were higher at low percentages of fruit. The results of the second stage (quality evaluation during storage) indicated that storage had a significant effect on pH, acidity, synersis, taste and texture (P<0.05). In samples which contained apple, coli forms disappeared after 7 days of storage. In samples that contained strawberry, coli forms disappeared after 7 days of storage.
S Mahbob Sharemi, A Forghani, H Ramezanpor,
Volume 13, Issue 49 (10-2009)
Abstract
Surface charge of soils is measured using two different approaches: ion adsorption and potentiometric titration. Most models of surface charge chemistry of soils have been derived from the data obtained by potentiometric titration. The Uehara and Gillmanُs model was used to estimate the surface charges at some soil pH range in three forest soils of Lahidjan region. The selected soils (Typic Udorthent, Typic Hapludalf, Ultic Hapludalf) were formed on three different types of parent rocks. So, the effect of parent rocks on surface charge characteristics was investigated. Soil samples were characterized through their organic carbon, clay percentage, pH in water and 1 M KCl, cation exchange capacity (CEC), point of zero charge of variable charge components (pH0), zero point of net charge(ZPNC) and charge variation. All soils had a significant amount of negative charge at soil pH. A Typic Hapludalf contained the lowest value of pH0 and the largest amount of negative charge at soil pH. The pH0 values were less in the surface than in the subsurface horizons. The ZPNC values were not obtained by the interpretation of charge variation curves and estimated lower than 2.5, which refers to high amount of negative charge in these soils. Differences in negative charge development in a pH range from 3 to 6 were largest for horizons rich in organic carbon and least for those with significant amounts of layer silicate minerals. Data obtained from charge variation curves of the studied soils also showed that the values of AEC were low and below 1 cmol/kg soil.
A.r Hosseinpur, M.r Panahi,
Volume 14, Issue 52 (7-2010)
Abstract
Potassium (K) fixation by phyllosilicates clay minerals is a very important process influencing the availability of K for plants. Information about K fixation is limited in Hamadan soils. The objectives of this research were to determine potassium fixation capacity (PFC) and potassium fixation index (PFI) of 10 surface soils of Hamadan province and the correlation of these parameters with soil charge characteristics. Potassium fixation capacity was obtained using six different levels of added K as KCl and three wetting and drying cycles. Also charge characteristics of soils were determined. Tetrahedral CEC of soils was determined after saturation of samples with LiCl and heating at 300 oC to reduce octahedral charge near zero. The results showed that tetrahedral and octahedral CEC ranged from 4.6 to 16.0 and 0.8 to 4.9 cmolckg-1 respectively. Mineral and organic portion CEC ranged from 6.1 to 20.9 and 0.97 to 9.7 cmolckg-1 respectively. The amount of PFC increased with increasing added K. Mean amount of PFC ranged from 58.2 to 175.03 mgkg-1. Potassium fixation index ranged from 0.23 to 0.67. The results of correlation studies indicated that PFI were significantly correlated with octahedral CEC, mineral and organic portion CEC, total CEC, exchangeable and nonexchangeable K. The results of this research showed that PFI very different in soils. So that this parameter should be consider in K soil testing.
P. Ashofteh, A. R. Massah Bouani,
Volume 14, Issue 53 (10-2010)
Abstract
Climate change has different impacts on extreme events such as flood and drought. However, in Iran there are few researches about the impacts. This research was aimed to investigate maximum annual discharge (magnitude and frequency) that may occur due to climate change in Aidoghmoush Basin during 2040-2069 (2050s). At first, monthly temperature and precipitation data of HadCM3 model under the SRES emission scenario, namely A2 , was provided for the basin. Then, these data were downscaled spatially and temporally to Aidoghmoush basin by proportional and change factor downscaling methods. Results showed that the temperature increases (between 1.5 to 4) and the precipitation varies (30 to 40 percent) in 2040-2069 compared with baseline period (1971-2000). A semi-conceptual model (IHACRES) for simulation of daily runoff was calibrated. Downscaled temperature and Precipitation for 2050s were introduced to IHACRES and daily runoff was simulated for the future. Probability distribution was fitted to maximum annual discharge series and the maximum discharge regime of the future was compared with the baseline. Results indicated that climate change affects Maximum discharge in the regime of the basin. Also, the analysis showed that the intensity of maximum discharges for the time period less than 50 does not show any significant difference but by increasing the return period, the intensity increases in future periods. Moreover, it was shown that the probability of maximum discharges with constant intensity will decrease in the future compared to the baseline.
