JWSS - Journal of Water and Soil Science

Dusts contain heavy metals such as Pb, Zn, Cu, Cr, Cd and As that can threat human's health and environment. Therefore, the spatial distribution of heavy metals concentration and soil pollution monitoring and environmental quality protection seem to be essential. To assess heavy metals pollution level in Ahvaz street dust, 115 street dust samples were collected from main pedestrians. The samples were analyzed by Atomic Absorption (AAS). The pollution level was estimated based on the geo-accumulation index (I_geo), contamination factor (CF) and the enrichment factor (EF). The average concentration values of Pb, Zn, Cu, Cr, Cd and As were found to be 197.6, 150.1, 179.7, 101, 5.6 and 14.2 mg/kg, respectively. Pearson's correlation coefficient also indicated that Pb, Zn, Cu and Cr had a significant correlation showing similar possible anthropogenic sources. On the other hand, Cd and As showed a lower correlation with other metals, indicating that they belonged to the geogenic sources. The results of contamination factor, enrichment factor and geo-accumulation index also indicated that Pb, Zn, Cu and Cd had a high contamination level.  Also, areas with high population density, heavy traffic volume, and industrial activities exhibited a high level of heavy metals contamination.

Wind erosion is one of the environmental problems worldwide, particularly in arid and semi-arid areas of Iran. Different methods and models have been proposed to measure and monitor wind erosion in the recent years. One of the accurate models for measuring f wind erosion is the USEPA model. The purpose of this study was to evaluate the quantification of wind erosion with the USEPA model and the comparison of different interpolation methods for drowsing high-precision soil erosion mapping. For this purpose, 50 samples from 0-30 depth were taken from the study area. Based on the analysis of the physical properties of the soil, including the distribution of the primary and secondary particle sizes, climatic parameters such as evaporation and transpiration, rainfall, wind speed and also, the vegetation and topography characteristics of the area, the erosion rates of Q, Q₃₀ and Q₅₀ were measured. Interpolation methods including general kriging, IDW, LPI and RBF were compared. The results showed that the highest erosion emission rate of Q₅₀ was 39 ton ha^-1. The highest and lowest erosion rates for the Q₃₀ index were 0.060 and 2.694 ton ha^-1, respectively; for the Q index, the highest and lowest erosion rates were 0.009 and 0.055 ton ha^-1, respectively. The results also showed that the IDW method for the Q₅₀ index with the minimum error rate (RMSE) values of 3.94 and the mean absolute error (MAE) with the valueof 1.89 had the best performance among the studied models. The LPI model Q had the best performance with the lowest error (0.0086) and absolute absolute error (0.0021).

The reuse of treated wastewater in countries such as Iran that suffers from drought is considered an important challenge in water management programs. The application of modern wastewater treatment systems particularly attached growth systems, owing to the short time required for start-up, low land requirements, and the absence of problems associated with sludge handling may be a resolution. The objective of this study is to investigate the performance of the Moving Bed Biofilm Reactor (MBBR) in treating synthetic municipal wastewater and selecting an appropriate model. In this way, a bench-scale reactor possessing an effective volume of 15 liters, and synthetic wastewater with influent COD of 500 mg/l (similar to typical municipal wastewater) has been used and the experiments with media filling percentages of 30%, 50%, and 70% and hydraulic retention times (HRT) of 4, 8, and 12 hours have been carried out. The observed data show that the optimum bulk density and hydraulic retention time are 50% and 4 hours, respectively. Also, the kinetic study of reactor performance indicates that Grau second-order model has better conformation with Moving Bed Biofilm Reactor results. In addition, a regression model for predicting effluent COD based on the filling percentage and retention time is presented.

Iran is located in the dry belt of the earth and is predicted to face water stress in the next half-century. Currently, the area of sugarcane cultivation in Khuzestan is over 85,000 hectares and due to the high water needs of sugarcane and drought conditions, optimization of water consumption and irrigation management is necessary to continue production. Therefore, in this study, the values of soil moisture, canopy cover, biomass yield in five treatments and irrigation levels (start of irrigation at 40%, 50%, 60%, 70%, and 80% soil moisture discharge) during 2 planting dates in the crop year 2015-2016 on sugarcane cultivar CP69-1062 in Amirkabir sugarcane cultivation and industry located in the south of Khuzestan was simulated by AquaCrop model. The measured data on the first culture date (D1) and the second culture date (D2) were used to calibrate and validate the model.  The results of NRMSE statistics in canopy cover simulation in calibration and validation sets with values of 2.1 to 15.6% and 3.8 to 18.3%, respectively, and in biomass simulation with values of 6.2 to 15.2%, and 9.5 to 12.6%, respectively and coefficient of determination (R2), range 0.98 to 0.99 indicated that the high ability of the AquaCrop model in simulation canopy cover and biomass yield. whereas, the values of NRMSE of soil depth moisture in the calibration and validation sets ranged from 11.6 to 23.8, and 12.2 to 22.7, respectively, with a coefficient of determination (R2), 0.73 to 0.96 (calibration) 0.8 to 0.93 (validation) showed less accuracy of the model in the simulation. The best scenario is related to the third proposal that water consumption, water use efficiency, and yield are 1710 mm, 1.53, and 42.27 tons per hectare, respectively, which shows a reduction in water consumption of 360 mm.