JWSS - Journal of Water and Soil Science

The contact angle is a numerical index of differentiation between hydrophilic and hydrophobic soils. The objectives of this research are: 1) assessing different methods such as capillary rise, the molarity of ethanol droplet, repellency index, and sessile drop, and 2) Determining the most efficient method in a typical soil with sandy loam texture. In this study, hydrophobic soil was hydrophobized artificially using stearic acid and according to the water drop penetration time classification method. Calculated contact angles of hydrophilic soil with capillary rise method, the molarity of ethanol droplet method, repellency index (two methods of calculation), and sessile drop method were 89.9, 75.41, (57.81), 56.28, and 58.91, respectively. Using the contact angle measuring device, the contact angle of five hydrophobic levels were 58.91, 104.92, 120.48, 129.96, and 173.07, respectively. According to the precession of the device where the operator is capable to control data and processes and there is no limitation in usage, therefore, the sessile drop method is the most suitable method to measure contact angle. The contact angle of the late method and water drop penetration data are positively correlated (R² = 0.975).

The reuse of treated wastewater in countries such as Iran that suffers from drought is considered an important challenge in water management programs. The application of modern wastewater treatment systems particularly attached growth systems, owing to the short time required for start-up, low land requirements, and the absence of problems associated with sludge handling may be a resolution. The objective of this study is to investigate the performance of the Moving Bed Biofilm Reactor (MBBR) in treating synthetic municipal wastewater and selecting an appropriate model. In this way, a bench-scale reactor possessing an effective volume of 15 liters, and synthetic wastewater with influent COD of 500 mg/l (similar to typical municipal wastewater) has been used and the experiments with media filling percentages of 30%, 50%, and 70% and hydraulic retention times (HRT) of 4, 8, and 12 hours have been carried out. The observed data show that the optimum bulk density and hydraulic retention time are 50% and 4 hours, respectively. Also, the kinetic study of reactor performance indicates that Grau second-order model has better conformation with Moving Bed Biofilm Reactor results. In addition, a regression model for predicting effluent COD based on the filling percentage and retention time is presented.

Due to the limitation and scarcity of water supplies, it is essential to identify and reuse alternative water sources, particularly in the arid and semi-arid regions according to environmental conditions. Reuse of runoff is an adaptive management philosophy and approach to balance efforts and provide sustainable water services and manage hazards. The present study is aimed to design a suitable model of water resource management with an emphasis on crisis management. In this study, indices and dimensions of the water resources management model were determined via the Delphi method (based on Schmidt, et al.). Delphi panel members were identified and selected in three stages using random sampling. The faculty members of water resources and watershed management university specializing and passive defense experts of water organization were selected as the Delphy panel members. Initially, panel members identified the most important effective items on water resources security, based on their inference of the model. Based on the first evaluation and after eliminating duplicates, 43 items remained. Finally, 36 items remained in the analyses, when the items with low and medium significance coefficients were eliminated. The final model of water resources management was approved by the expert opinion based on the crisis management approach. According to the results, designing rainwater collection and storage systems in different parts of the city and installing tanks for roof rainwater collection in each home were selected as the best approach in the critical condition (with an average grade of 4.94), whereas the installation of the sensors in different parts of water pipe with an average grade of 2.10 was ranked in the 33rd selection. Finally, the items identified by the Delphi panel were classified into four general indices: retrofit, safety, culture, and planning. In general, it is necessary for the officials of urban water resources, as well as crisis management, must prepare for crisis conditions as well as the correct, principled, and scientific use of available water resources to extract and store rainwater and runoff to use it in crises and disrupt the general water supply system.

To investigate and evaluate the effects of different levels of drip irrigation on grain yield and yield components, oil yield, seed oil percentage, and seed water use efficiency, an experiment was performed at Behbahan Agricultural Research Station during two crop years 2018-19 and 2019-20. The experiment was conducted in split plots based on a randomized complete block design with 3 replications. The amount of water in tape drip irrigation was compared at four levels of 40, 60, 80, and 100% water requirement in main plots and two sesame cultivars Local of Behbahan and Shevin in subplots from the beginning of flowering. Comparison of mean interaction effects of irrigation levels and cultivars showed that the treatment of 100% water requirement in the Behbahan local cultivar with the yield of 1218.0 kg/ha was ranked first and foremost. Water consumption in the highest treatment (100% water requirement and Behbahan local cultivar) was calculated to be 5389.4 m³/ha. Treatments of 100% and 80% of water requirement in superior cultivar (local Behbahan) with water use efficiency of 0.226 and 0.210 kg/m³ had no significant difference, respectively, and were in the first place. Pearson correlation coefficient calculated for the measured traits showed that the highest correlation of water volume was calculated (r = 0.9271) with the weight of one thousand seeds. Significant correlations of water volume with grain yield and yield components indicated that sesame was susceptible to drought stress and attention to optimal water management in sesame cultivation. Therefore, decreasing the volume of water consumed and consequently drought stress in sesame reduced yield and yield components.

The simulation of the rainfall-runoff process in the watershed has particular importance for a better understanding of hydrologic issues, water resources management, river engineering, flood control structures, and flood storage. In this study, to simulate the rainfall-runoff process, rainfall and discharge data were used in the period 1997-2017. After data qualitative control, rainfall, and discharge delays were determined using the coefficients of autocorrelation, partial autocorrelation, and cross-correlation in R Studio software. Then, the effective parameters and the optimum combination were determined by the Gamma test method and used to implement the model under three different scenarios in MATLAB software. Gamma test results showed that today's precipitation parameters, precipitation of the previous day, discharge of the previous day, and discharge of two days ago have the greatest effect on the outflow of the basin. Also, the P_t Q_t-1 and P_t P_t-1 Q_t-1 Q_t-2 Q_t-3 combinations were selected as the most suitable input combinations for modeling. The results of the modeling showed that in the support vector machine model, the Radial Base kernel Function (RBF) has a better performance than multiple and linear kernels. Also, the performance of the Artificial Neural Network model (ANN) is better than the Support Vector Machine model (SVM) with Radial Base kernel Function (RBF).

Water hammer is one of the unsteady flows in urban water distribution networks, which has been of great importance due to the damage caused to the pipeline and has always been of interest to researchers. In this study, the phenomenon of water hammer due to the sudden closure of the valve in the downstream end has been investigated in a laboratory and using a numerical model. In the laboratory section of the study, the effect of flow changes with control equipment and without control equipment on the maximum and minimum height of pressure wave head was investigated. The results showed that the proper performance of the surge tower pipe in reducing the maximum pressure wave as well as improving the negative pressures in the system. In a maximum discharge of 35.75 liters per minute, surge tower pipe reduced pressure wave head by a maximum of 70.40%. In a minimum discharge of 7.70 liters per minute, the surge tower pipe reduced the height of maximum pressure by 34.82%. Also, in minimum discharge, surge tower pipe has improved the minimum pressure wave head by more than 78%. AFT Impulse numerical model was used to analyze the water hammer. The results of the numerical model were examined in a benchmark problem using a characteristic method and its validity was confirmed. Simulation of laboratory model with numerical software showed that this software only predicts the first wave properly when water hammer produces negative pressures, but in the next cycles it does not show the depreciation rate of the pressure wave, properly.

Reducing surface water resources and successive droughts and consequently excessive use of groundwater resources, especially for agricultural purposes, have caused irreparable damage to the natural resources of the country. In the meantime, knowing the status of the water balance of the plain can help to effective management of water resources in the region. Samalqan plain is located in a semi-arid climate in North Khorasan Province. Since the surface water resources for water supply are not very reliable, so, the main source of water supply in the region is well. Due to the existence of rivers in the plain, the low thickness of the alluvium, groundwater level fluctuations, and the high uncertainty in the calculation of hydrodynamic coefficients, the need for careful hydrogeological studies and determining the role of each parameter affecting groundwater is necessary. This study was conducted to simulate the Samalqan aquifer and analysis of water balance for the years 2003 to 2013 using the MODFLOW model. To identify the groundwater recharge rate, this component was estimated by the SWAT model. Calibration and validation of the model with an error of 1.1% and 1.2%, respectively, indicated that an appropriate estimation between the simulated and observed heads. Assessment of the groundwater hydrograph in the observation wells showed that the groundwater level in most places has many monthly and seasonal fluctuations. After drawing the potential lines of the plain, the inputs and outputs were identified, and using the reserve volume changes, the water balance was determined. The results showed that the water balance of the plain was negative and the reservoir deficit was estimated at 9.14 million cubic meters. Therefore, this model can be used to predict the future situation of aquifer and the management of water resources in the region.

The application of simulation-optimization models is a valuable tool for selecting the appropriate cropping pattern. The main objective of this research is to develop a two-objective simulation-optimization model to determine the pattern of cultivation and water allocation. The model performs the optimization with the multi-objective metamorphic algorithm (MOALO) after simulating different states of the cultivation pattern. The decision variables including land and water allocated to ten-day periods of plant growth were designed in a way that the minimum utilization of water resources and economic maximization were identified as target functions. The developed model was used to simulate and optimize the cultivation pattern with an area of ​​5500 hectares and water allocation of Semnan plain with renewable water at the rate of 60.8 million cubic meters. Harvesting scenarios of 80 (GW80) and 100 (GW100) percent of renewable groundwater and scenarios of change in existing cropping pattern of 30 (AC30) and 60 (AC60) percent were considered and each scenario was simulated with the MOALO algorithm. Optimization using the proposed model in four scenarios improved the water and economic objective functions compared to the initial simulation performance. The results showed that the four proposed scenarios were obtained by minimizing the water objective function and maximizing the economic objective function relative to the current situation (simulation). In general, the proposed model had a good performance despite its simplicity, which is a specialized tool to optimize the crop pattern with water allocation.

Integrated assessment of the watershed is critical in arid and semi-arid areas due to the severe water stress in these regions. Data and information are an essential part of decision making and water governance to obtain integrated water resources management at the watershed scale. Water accounting is a helpful tool to organize information and present them as the standard indicators to achieve this goal. Therefore, the objective of this study is to implement the Water Accounting Plus framework (WA+) in the Ferizi watershed located in the Khorasan-e Razavi Province. In this study, water accounting indicators of the Ferizi watershed for a period of 28 years (1990-2017) and wet (1990-1997) and dry (1998-2009) periods were calculated using the SWAT model. The calculated indicators showed that the amount of manageable water and usefulness of consumption (transpiration) is low in the watershed and a large part of the share of irrigation in the watershed is provided by groundwater resources. Generally, the results of this study showed that the use of the SWAT model, WA+ framework, and analysis of water accounting indicators play a significant role in assessing the agricultural and hydrological conditions of the watershed. The proposed approach in this study can help managers make enlightened decisions to keep the sustainability of the watershed.

One of the ways to reduce the amount of wastewater pollution is the use of constructed wetlands. In this research, the performance of a hybrid constructed wetland with pumice ore and vetiver plant on urban wastewater has been investigated. Hybrid wetlands with these specifications were constructed in the vicinity of wastewater treatment at the Isfahan University of Technology. To evaluate the performance of constructed wetland the effects of three and six days of retention time on the removal efficiency were studied using a completely randomized design. On average, for three days of retention time, in the wetland with the vertical flow, the horizontal flow, and hybrid wetland, fecal coliform was 47.4, 98.3, and 99.1 percent, BOD₅ was 7.6, 20.9, and 26.9 percent, and the COD was 4.6, 40.0, and 42.7 percent decreased, respectively. Also, during the six days of retention time in the wetland with the vertical flow, the horizontal flow, and hybrid wetland, fecal coliform was 61.6, 99.3, and 99.8 percent, BOD₅ was 10.7, 29.9, and 37.4 percent, and COD was 16.0, 86.8, and 88.9 percent decreased, respectively. The combination of Pumice as a porous material with the ability to absorb the elements as well as vetiver as a plant capable of phytoremediation indicated a very suitable performance during low retention time.

The present research was conducted to determine water stress tolerance and water productivity (WP) of 5 alfalfa cultivars as a split-plot design in a randomized complete block with 3 replications in the Safiabad Agriculture and Natural Resources Research Center (SARRC) with Silty clay loam soil texture during 2018-2019. The main plot was 4 levels of water irrigation depth (including 25, 50, 75, and 100% water requirement supply) with a constant irrigation cycle and the sub-plot was the five alfalfa cultivars (Baghdadi, Yazdi, Nikshahree, Omid, and Mesasirsa). Two-year data on forage yield and WP for six harvests (from June to November) were analyzed by SAS software. The results showed that the wet and dry forage yield decreased by applying water stress and the percentage of dry forage increased. The highest yield of dry matter (12.4 tons ha^-1) and WP of dry forage (0.94 kg m^-3) were obtained from 75% water requirement supply treatment. Baghdadi genotype with wet and dry forage yield 39.1 and 10.7 tons ha^-1, respectively, and the WP of dry forage 0.9 kg m^-3 was higher than other genotypes. However, the Yazdi genotype had the lowest yield of wet and dry forage (30.3 and 8.5 tons ha^-1, respectively) and dry forage WP (0.75 kg m^-3). Therefore, the Baghdadi genotype with a 75% water requirement supply is recommended for similar conditions to the climate of Northern Khuzestan to increase water productivity.