Showing 13 results for Heidarnejad
M. Shabanian, H. Masomi, A. Hoseinipour, J. Heidarnejad, Z. Azami,
Volume 11, Issue 1 (spring 2007)
Abstract
Cucumber cultivars, grown in greenhouse in the Jiroft region, were surveyed for the relative incidence of Zucchini yellow mosaic virus (ZYMV), Watermelon mosaic virus-2 (WMV-2), Cucumber mosaic virus (CMV) and Tomato spotted wilt virus (TSWV) from 2001 to 2004. Samples from 1294 plants representing different cultivars were analysed by Enzyme-linked immunosorbent assay (ELISA) and Dot immunobinding assay (DIBA). The data showed that green-house cucumbers are infected by CMV, ZYMV, TSWV and WMV-2. However, ZYMV was the most prevalent virus. Mixed infection including double and triple infection was identified in some samples. Transmission of aphid-borne viruses (CMV, ZYMV and WMV-2) by Aphis gossypii, A. fabae, A. craccivora and Myzus persicae revealed that ZYMV is most efficiently vectored by these aphids and, A. craccivora transmitted these viruses with more than 60% efficiency. In addition, WMV-2 was not transmitted by A. gossypii. In RT-PCR, ZYMV infection was confirmed by amplifying a PCR product of the predicated size 458 bp, using total RNA extracted from infected plants. All ZYMV infected samples reacted with monoclonal antibodies (705-1, 705-2 and 705-4) in TAS-ELISA test. These results showed that ZYMV isolate collected from Jiroft belongs to group A, cluster 1 or 2. In electron microscopy study, normal length of ZYMV flexuous particles in partial purified preparation was calculated as 790 nm. The molecular weight of coat protein of ZYMV was estimated at 36 KDa., using SDS-PAGE and western blotting. This is the first report of these viruses in greenhouse grown cucumber in the Jiroft region.
N. Zohrabi, A. Massah Bavani, E. Goudarzi, M. Heidarnejad,
Volume 20, Issue 77 (Fall 2016)
Abstract
Since climate change is regarded as a serious threat to different parts of life cycle, separation of factors intensifying this phenomenon seems necessary. This research has investigated the temperature and precipitation trend using the multiple trend test in the upstream Karkheh basin located in west of Iran. For this purpose, two-dimensional graphs of temperature and precipitation anomalies of the CGCM3 Model (1000-year data) were drown for the study area. Then, the attribution of changes in climate variables due to climate internal fluctuations or greenhouse gases affected by human factors were investigated. Based on the findings of this study, in different parts of the study area, the range of natural climate variables for temperature and precipitation changes (95% probability) in the west of the study area are
± 1.4ºC and ±76%, respectively.
The results showed increase and decrease in temperature and precipitation in most of the studied stations, respectively. The variables of temperature and precipitation are affected by climate change and as we approach latest years, especially in the western and central parts of the study area, the impact of greenhouse gases in increasing temperature and reducing precipitation becomes more evident. According to the current results it can be concluded that changes in land use in Iran caused by human interventions can be introduced as a significant factor for the ascending trend of temperature. However, it can be noted that the most important factors of the increased greenhouse gases in recent years are human activities such as land use changes. These changes certainly have affected water resources in the study area.
E. Gravandi, A. Kamanbeadst, A. R. Masjedi, M. Heidarnejad, A. Bordbar,
Volume 22, Issue 3 (Fall 2018)
Abstract
Rivers has long been regarded as one of the most basic human water supplies. If the topography, a morphology, water requirements conditions, etc. allow water to be transferred to gravity, the use of the dike can have a significant impact on the flow rate and the sediment input to Intake. Dike design needs to consider several parameters such as position, length, type, etc. Using a good design can increase the input flow rate and reduce the sediment entering it. In this study, to evaluate the dike impact on flow hydraulic conditions in the Intake with different situations, 30, 45, 60 and 90 degrees two simple L-shaped dikes in the upstream and downstream Intake and for five inlet flows (0.7, 1.12, 2.84, 5.04 and 6.23 Lit/s) were considered in the laboratory flume made by the author as a physical model to simulate the flow of the basin; then different effects of the dike on the hydraulic flow were studied. The results of the tests showed that the L-shaped dike in the upstream and downstream Intake in the internal arc flume increased the inflow flow rate into the Intake. Also, the best angle of deviation for the maximum flow entered the Intake angle of 60 degrees.
R. Monjezi, M. Heidarnejad, A. R. Masjedi, M. H. Pourmohammadi, A. Kamanbedast,
Volume 23, Issue 2 (Summer 2019)
Abstract
Nonlinear weirs are regarded as important hydraulic structures for water level adjustment and flow control in channels, rivers and dam reservoirs. One example of non-linear weirs is shaped as curved-zigzag. The crest axis of these weirs is non-linear. At a given width, the crest length is greater than that of the conventional linear weirs. Thus, they achieve a higher flow rate for an identical hydraulic load. This research experimentally focused on the discharge coefficient and flow rate of curved weirs with three different curve radii in two triangular linear and zigzag shapes. The discharge coefficients of these weirs were comparatively explored in terms of the hydraulic performance as a function of the total hydraulic load to weir crest height ratio (hd/P) and curvature angle (θ) (or curve radius). The results indicated that for the same hydraulic load, the increase of θ (the decrease in curve radius) led to a lower discharge coefficient; this was first because of the increased topical rise of water level, and then the more indirect path with a greater curvature through which the flow had to transport. Both factors could negatively affect the water discharge coefficient. In practice, the runoff coefficient at a weir with a curve radius of R/w=1.25 was approximately 8.5% greater than that of a weir with a curve radius of R/w=0.75 under a hydraulic load of 0.2.
J. Rouzegar, A. A. Kamanbedast, A. Masjedi, M. Heidarnejad, A. Bordbar,
Volume 23, Issue 3 (Fall 2019)
Abstract
Morning glory spillway is one of the spillways that used to passing of flood from high to low level. This spillway is used in the reservoir dams that are placed in narrow valleys and in many locations with high slope in reservoir walls. In the Morning glory spillways, the vortex flow can reduce discharge, discharge coefficient and the performance of spillway. The zigzag spillway, as another type, is introduced as a proper option for compensating the problem of passing maximum possible flow rate, usually encountered by spillways. In the present study, the experimental results of a physical model were used to develop a hydraulic design with squire and circle inlet and analysis method for Labyrinth Morning Glory Spillway. The analysis of experimental data in circle and square inlet showed, that increase in length of spillway and zigzag, causes decrease in the discharge coefficient. Finally the result of effect spillway inlet on flow rate demonstrate that discharge coefficient in square inlet is more than circle, whereas without vortex breaker.
Gh. Safarinejadi, M. Heidarnejad, A. Bordbar, M. H. Pourmohammadi, A. Kamanbedast,
Volume 23, Issue 4 (Special Issue of Flood and Soil Erosion, Winter 2019)
Abstract
The use of free launch jets in flip bucket structures with associated submerged ponds, in the appropriate geological, and topographic and hydraulic conditions, could have significant economic and safety benefits. In this research, the downstream scour phenomenon of a flip bucket jet was investigated in free conditions, as well as in the presence of a trapezoidal and triangular slot in the coastal manner with different layout intervals at flow rate of 9, with a total of 45 experiments. The results of this study showed that the presence of the slot had significant effects on the depth and range of scour, so that the fit bucket jet with alternate triangular slots reduced the scour by about 12.7%, as compared to the no slot mode. Moreover, the maximum scour depth occurred in the bucket mode with the alternate trapezoidal slots in the more favorable interval than the rest of the models. Then, the results were compared with several empirical formulas and Veronese A relation showed closer results to the actual values.
A. Saki, A. A. Kamanbedast, A. Masjedi, M. Heidarnejad, A. Bordbar,
Volume 23, Issue 4 (Special Issue of Flood and Soil Erosion, Winter 2019)
Abstract
After Hamidieh Diversion Dam near the city of Hamidieh, Karkheh River is divided into two streams known as Hufel and Nissan. At the lower flow rates, Nissan makes up a greater share than Hufel due to the steeper slope of the former. This study attempted to construct a hydraulic structure to appropriately divide water flow in Hufel. In a laboratory experiment, a flume with a 90-degree bend was used at Islamic Azad University of Ahvaz. Various experiments were conducted at different widths and heights. Furthermore, this model was simulated through CCHE2D, the results of which were compared against those of physical and mathematical models. The results indicated that the weir height increased the deviation flow percentage to the Hufel stream due to rising water level. Moreover, the deviation flow percentage to Hufel was declined as the weir width was increased due to falling water level. At Hufel, the installation of rectangular weir in different dimensions yielded the minimum of 34.3% and the maximum of 61.5% increase in the flow rate. In the normal mode without any weirs installed, however, there would be an increase in the flow rate, as compared to the mode where a weir has been installed. This can be associated with the flow controlled by the weir. On average, the deviation flow rate was increased by 2.8% in the weir mode and 7.7% in the weir-less one. An increase in the Froude number from 0.21 to 0.38 led to a lower average deviation flow rate by 19.3%. Moreover, the results of the simulation through CCHE2D were demonstrated to be largely similar to those of physical model experiments. However, an increase in the Froude number did not lead to a decline in the deviation flow rate (i.e. it remained constant). This trend was inconsistent with the results of the physical model.
S. A. Banishoaib, A. Bordbar, A. A. Kamanbedast, A. Masjedi, M. Heidarnejad,
Volume 23, Issue 4 (winter 2020)
Abstract
A ‘spillway’ is a structure used to provide the controlled release of flood water from upstream into downstream area of a dam. As an important component of every dam, a spillway should be constructed strongly, reliably and efficiently to be used at any moment. Labyrinth and stepped spillways are presented as appropriate modifications to those spillways hardly capable of managing the maximum potential discharge. Owing to their nonlinear crests for a given width, labyrinth and stepped spillways have a larger discharge rate than linear- crest spillways at an identical height. Compared to other energy dissipaters, the combination of stepped and labyrinth spillways is known as a very strong energy dissipater. In the following part, the combination of these two structures and their dimensional change for increasing the water- energy dissipation are addressed. To conduct this study, an experimental flume with a 90- degree bend in the Islamic Azad University of Ahwaz was used. In total, 90 experiments were conducted on three different labyrinth- shape stepped spillway models with two different lengths, three different widths, and five different discharges. Analysis of the results showed a greater energy loss reduction in triangular rather than rectangular or trapezoidal labyrinth- shape stepped spillways. In addition, energy loss was greater in labyrinth spillways with two cycles than those with one cycle. Energy loss was increased by raising the Froude number from 0.05 to 0.1; in contrast, energy loss was decreased with increasing the Froude number from 0.1 to 1.0, which was due to the submergence of steps, a decrease in the roughness of steps and an increase in the intensity of aeration.
R. Gharibvand, M. Heidarnejad, H. A. Kashkouli, H. Hasoonizadeh, A. Kmanbedast,
Volume 24, Issue 1 (Spring 2020)
Abstract
The flow fields over a trapezoidal labyrinth weir (two-cycle) and a piano key weir were simulated using Flow3D, studying the impact of each model on the flow field in the weirs and the coefficient of discharge in comparison with the available experimental data. Moreover, the models were investigated experimentally in a 12.5 m long, 0.3 m wide, and 0.4 m high rectangular flume under clear-water conditions. The results showed good agreement between the data from the numerical and experimental models. The piano key weirs had a higher coefficient of discharged compared with labyrinth weirs. The coefficient of discharge was observed to increase by 26 percent as the height of the PKW was increased by 50 percent (from 5 to 7.5 cm). This increase was 24 percent for labyrinth weirs.
A. R. Bahrebar, M. Heidarnejad, A. R. Masjedi, A. Bordbar,
Volume 25, Issue 2 (Summer 2021)
Abstract
The combination of a labyrinth weir with an orifice is a proper solution for floating material to pass over the weir and transfer sediment through the orifice. Additionally, creating a slot in the overflow wing leads to higher discharge. This study examined four discharges (5, 10, 15, and 20 liters per second) with channel width and height of 30 and 40 cm in trapezoidal-orifice, square-orifice, and triangular-orifice labyrinth weirs in the laboratory and using Flow3D with RNG k-epsilon (k-ε) turbulence model, the results were compared with one another. Comparing the discharge flow over weirs and measuring the discharge coefficient among the mentioned models showed that the triangular-orifice labyrinth weir had the highest discharge rate. Moreover, the increased Ht/P ratio (Ht represents total hydraulic head; P denotes weir height) for all models resulted in the increased discharge coefficient. Due to the efficiency of this type of weirs, the highest discharge coefficient was obtained at low Ht/P ratios. At lower ratios, since there was free flow, the coefficient of weir discharge increased, and as the ratio increased, the weir was partially submerged. Furthermore, for the weir design, the best Ht/P ratio was between 0.13 to 0.41, and the maximum discharge coefficient (Cd = 1.2) was within this range.
M. Eskandari, M. Heidarnejad, A. Egdernezhad,
Volume 27, Issue 3 (Fall 2023)
Abstract
The formation of vortices behind the gates of diversion dams is an operational challenge. Such vortices lead to vibration and corrosion in the gate, reducing the lifetime and raising the operational cost of the dam. This study investigated these vortices and their formation. It was found that the gate or cutoff wall was not the only explanation for the vortices; the closed side gates also contribute to vortex formation. Furthermore, an increase in the gate width reduced vorticity; the vortex size experienced a 200% reduction as the gate size increased by 200%. The cutoff wall diameter was another determinant. An increase in the cutoff wall diameter raised vorticity. The vortices increased by 50% as the wall diameter increased by 150%.
M. Dorfeshan, A.r. Masjedi, M. Heidarnejad, A. Bordbar,
Volume 27, Issue 3 (Fall 2023)
Abstract
Piano key overflows have a high discharge capacity. Proper design of these overflows requires sufficient accuracy in predicting the type of overflows. In this study, experiments were performed in a rectangular laboratory flume made of Plexiglas to investigate the effect of the relative length and width of the two-cycle piano switch overflow crest on the discharge coefficient. In present research, the flow intensity coefficient was investigated by installing a rectangular piano switch overflow with relative crest lengths of 0.8, 1, and 1.2 and relative crest widths of 0.2, 0.3, and 0.4 in 10 flow intensities in the channel. The results of this study showed that by increasing hydraulic load, the flow intensity coefficient first increases and then decreases. Also, by increasing the relative length of the crest by 50%, the current intensity coefficient increases by 43% in the overflow. Increasing the relative width of the overflow crest by 50% increases the current intensity coefficient by 25% in the overflows. Also, an equation was presented to determine the maximum relative scour depth, and the correlation coefficient of the results of this equation with the laboratory results is about 0.90.
M. Sehat, A. Bordbar, A.r. Masjedi, M. Heidarnejad,
Volume 27, Issue 4 (Winter 2023)
Abstract
Today, abutments disrupt the normal flow of rivers and cause scouring and erosion of sedimentary materials around them, creating holes and resulting in much damage every year. Researchers have proposed various methods to reduce the power of water erosion. One of the essential methods in this regard is creating slots in abutments. Since the expansion of the scour hole endangers the stability of the bridge structure, this study examined the effect of slot dimensions in the support on the scour hole dimensions. The findings demonstrated that the presence of slots in abutments effectively reduces the dimensions of scour holes. With the slot, the volume of the scour hole can be reduced by up to 50%. Furthermore, as the relative speed of scouring increases by 75%, the depth of the scour hole also increased up to 140%. An increase in slot depth leads to a decrease in scour hole depth of up to 85%.
