A. A. Azizi Zehan, A. A. Kamgar-Haghighi, A. R. Sepaskhah,
Volume 10, Issue 1 (4-2006)
Abstract
Iran with a cultivation area of 45000 ha and production of 150 ton/year is the number one saffron producer in the world. Planting of large size corms will increase flowering, but production of corms (number and size) may be affected by irrigation method or frequency. In this research which is performed in the farm of College of Agriculture, Shiraz University, the effects of method and frequency of irrigation on corm production, and the effect of produced corms on flowering were evaluated in two consecutive years. Two irrigation methods (basin and furrow) with four levels of irrigation frequencies (12, 24 and 36 days and dryland farming) were applied. In August of 2000 sample corm was taken from every plot, and the effect of applied treatment from previous growing period on corm production and the effect of produced corms on future flowering were evaluated and analyzed. Based on the results, in furrow irrigation, total number of corms and total number of corms smaller than 4 gr is significantly higher than basin irrigation. In all of the above cases, irrigation frequencies did not show a meaningful difference between themselves or in comparison with dryland farming treatment. Total weight of corms and number and weight of corms larger than 8 gr in basin irrigation were more than furrow irrigation. This is to the extent that it is considered as the main reason for the difference in the flowering of corms, and has caused the flowering of basin irrigation to be significantly higher than furrow irrigation. In basin irrigation, irrigation frequencies of 12 and 24 days had the highest amount of flowering. No significant difference was observed on average corm production between the treatments in the two irrigation methods. However, irrigation treatments in both irrigation methods showed significant differences when compared with dryland farming treatment. So, basin irrigation with irrigation frequency of 24 days is preferred over furrow irrigation due to lower water consumption and production of larger size corms which is effective in flowering.
S.a. Mohseni Movahed, M. Koochakzadeh, P. Salehimoghadam,
Volume 21, Issue 3 (11-2017)
Abstract
Basin irrigation is one of the conventional surface irrigation methods used to irrigate many crops all over the world. EDOBASIN, a new mathematical model for evaluation, design and optimal operation of basin irrigation has been introduced in this paper. In this model the linear combination of desired efficiencies are considered in an objective function, and based on decision variables that include discharge, length and width of basin and also restrictions of parameters, the optimal design is performed. This model is a simulation-optimization model in which the volume balance equations are used for hydrodynamic simulation and SA method are used for optimization steps. Optimization capabilities with various decision options and allowing weights to the indicators are good characteristics of this model. Comparison of advance time in this model with the well-known model SIRMOD for a real condition showed a good accuracy in the evaluation phase. In addition, the significant improvement of efficiencies after optimizing them simultaneously indicate that the model is an efficient tool for optimal design and use of this model for a data plot of an experimental field could enhance the efficiency of deep percolation ratio and application efficiency to 20% and keep constant the level of 100% for the efficiencies of water requirement and distribution uniformity.
M. Akbari,
Volume 24, Issue 4 (2-2021)
Abstract
The objective of this research was the development of a hydraulic-economic simulation-optimization model for the design of basin irrigation. This model performed hydraulic simulation (design of basin irrigation), using Volume Balance model, economic simulation through calculating sum of four seasonal costs and optimization using NSGAII multi-objective meta-heuristic algorithm. For programming, MATLAB programming software was applied. The optimizations of functional, multi-dimensional, static, constraint, continuous, multi-objective and meta-heuristic were applied for the optimization of the objective functions. Decision variables selected from simulation inputs were calculated in such a way that the hydraulic objective function (minimizing linear combination of seven performance indicators) and economic objective function (total seasonal cost based on sum of water cost, labor cost, basin preparing cost and channel drilling cost) were minimized. Data of one the experimental field was used for the purpose of simulation. After initial simulation, optimization of the experimental field was done using NSGAII multi-objective meta-heuristic algorithm with tuned parameters. Optimization using the suggested model shoed the decrease (improvement) of objective functions rather than initial simulation performance. As a result, the suggested model could be regarded as is a specialized tool for basin irrigation, showing a good performance, despite its simplicity.
