Showing 21 results for Drainage
M. R. Yazdani, M. Ghodsi, S. F. Mousavi,
Volume 11, Issue 1 (4-2007)
Abstract
Cultivation of a second crop in paddy fields of Guilan province is a strategy for optimum use of land, supporting family economy and increasing oil-seed production. However, this is impeded under high rainfall and waterlogging conditions. To enhance second-crop cultivation in paddy fields, surface drainage is inevitable. The surface drainage practices should be performed with minimum costs, least time span and least variations of the land. In the present research, longitudinal surface drains were constructed with a spacing of 2, 4, 6, 8 and 10 m (depth of 20 cm), with and without 1-m lateral drains (depth of 10 cm) in Rice Research Institute, Rasht, Iran. The experiment was conducted in a complete randomized block design with three replications. Canola (Brassica napa), variety PF, was cultivated as a second crop after rice. The results showed that the effects of drain spacing on seed yield, days to maturity, number of plants per m2, and also the effects of lateral drainage on seed yield, plant height, residual N, days to maturity, and number of plants per m2 are significant (P<0.01). Highest yield (2493 kg/ha) was obtained from longitudinal drains 4 m apart, with lateral drainage drain spacing of 6 and 2 m had acceptable yields, too (2241 and 1817 kg/ha, respectively). For treatments without lateral drainage, 2-m drain spacing had the highest yield (1324 kg/ha). Considering all the expenses for drainage construction, it was found that net benefit of longitudinal drain spacing of 4 and 6 m was twice the costs. Since the rainfall in Nov., Dec., and Jan., 2000, was higher than the 20-year average rainfall of the same months, it was concluded that the results of this experiment may be recommended in the years with a rainfall less than the year 2000.
S. Azizpour, P. Fathi, K. Nobakht-Vakili,
Volume 16, Issue 60 (7-2012)
Abstract
Soil saturated hydraulic conductivity (k) and effective porosity (f) are the most important parameters to simulate the processes associated with irrigation, drainage, hydrology, leaching and other agricultural and hydrological processes. Present methods to measure these parameters are often difficult, time consuming and costly. Therefore, a method which provides more accurate estimates of these parameters is essential and is considered inevitable. The purpose of this study was simultaneous estimation of k and f using approach inverse problem. In this study, analytical drainage model of Glover-Dam was used to simulate the inverse problem method. Also, genetic algorithm was used as an optimization technique for determination of optimal values of k and f. In order to measure the data required for calibration and evaluation of the proposed inverse problem model, a physical model was designed and constructed in the laboratory. The results showed that the proposed method is good for simultaneosly estimating simultaneous soil k and f. Also with variable f assumption, the prediction error of water table around the drainage was reduced significantly.
S. Marofi, N. Parsafar, Gh. Rahimi, F. Dashti,
Volume 16, Issue 61 (10-2012)
Abstract
In this study, a completely randomized experiment was designed with four irrigation treatments and three replicates. The irrigation programs were raw wastewater, treated wastewater, a combination of 50% raw wastewater and 50% potable water and a combination of 50% treated wastewater and 50% potable water. The experiments were run within a greenhouse. The lysimeters were built up on September 2009 and they were filled with two layers of soil. The upper (0-30 cm in depth) and lower (30-70 cm in depth) layers were sandy loam and sandy clay loam, respectively. A total of eight watering programs with an interval of elevens-day were applied. After each irrigation program, intake wastewater and drainage water of each Lysimeter was sampled in order to analyse the transport of heavy metals (Cu, Zn, Fe and Mn, Ni, Cd and Pb). Results showed that the effect of water quality was significant on percentage of transport of heavy metals. The lowest transport percentage of heavy metals belonged to raw wastewater treatment. Also, the highest percentage of transport of Cu, Zn, Fe, Ni and Pb belonged to the combination of 50% raw wastewater and 50% potable water. In most cases, we observed that the transport percentage of these elements increased by continuing the irrigation
J. Abedi Koupai, S. S. Eslamian, M. Khaleghi,
Volume 16, Issue 62 (3-2013)
Abstract
Crisis of quality and quantity of water resources is one of the most important problems in arid and semi-arid areas such as Iran. Wastewater treatment and reuse as a potential source of water can not only compensate for the water scarcity but also can prevent the hazardous pollutants from entering the groundwater and surface water resources. There are various methods to improve water quality, among which method of filtration is an effective and efficient method to remove elements. The most important issue for filter system is the selection of adsorbent materials. In this work, the tire chips were used as adsorbent. Column adsorption tests in a pilot system were conducted in two distinct steps using two types of water, including salt water and industrial effluents. Each test was conducted as a factorial experiment with three factors based on a completely randomized design with three replications. Three factors were studied including particle size (2-5 mm and 3-5 cm), filter thickness (10, 30 and 50 cm) and sorbent contact time with solution. The results showed that adsorption rate increased by increasing the thickness of the filter and sorbent contact time with solution. The best performance of reducing the salinity was observed in the treatment with 50 centimeter thickness and 24 contact hours. The salinity of this treatment was reduced by 20.3 percent (in the test with salt water) and 11.2 percent (in the test with industrial effluents). This filter reduced the heavy metals of lead, zinc and manganese up to 99, 72.1 and 41.4 percent, respectively. Also, the performance of millimeter and centimeter particles did not show a significant difference. Generally, the tire chips showed a proper performance to improve the water quality especially for industrial wastewater.
H. R. Owliaie,
Volume 16, Issue 62 (3-2013)
Abstract
Iron and manganese oxides as well as hydroxide minerals are among active constituents in soils because they are sensitive to environmental changes and often move frequently along soil profile. Therefore, their chemical forms content and their ratios are used as a soil developmental criterion. The present study was conducted in order to evaluate the effects of topography and drainage conditions on chemical forms of Fe and Mn along a soil catena in Dasht-e- Roum plain, in Kohgilouye Province. According to the results, maximum pedogenic Fe and Mn (Fed and Mnd) was found in more stable geomorphic surfaces. Higher values of Fed and Mnd were mostly observed in surface horizons compared to soil depth. Aquic soils exhibited higher contents of poorly crystalline Fe and Mn (Feo and Mno) and higher contents of Fed and Mnd. A significant correlation between clay content and Feo, Mno, Fet and Mnt contents was found. In addition, aquic condition increased Feo/Fed, Mno/Mnd and Mnd/Fed, 3.1, 4.3 and 1.9 times respectively but decreased the Fe crystallinity index 2.6 times. Aquic soils seem to have more favorable conditions for the formation of pedogenic Mn compared to pedogenic Fe, hence higher content of Mnd/Fed was observed in these soils
S. Jafari, H. Nadian,
Volume 18, Issue 69 (12-2014)
Abstract
The aim of this study was to evaluate soil properties changes in a soil toposequence series in Khuzestan province. Twelve soil profiles were dug in north to south direction in this province, according to the changes of the slope in Karoon’s alluvial deposits. The results showed that soil texture regularly changes to heavier form from north to south. It was slightly of redoxomorphic features in low land. Therefore, salic horizon was formed in this land. Despite high water table in this area, gray or mottle forms were few due to high soil salinity. The carbonates were eluviated from surface to subsurface horizon therefore, calsic horizon was formed due to illuviation. Secondary carbonate accumulation was maximum in the studied area. Both classic horizon and cambic horizon were formed in some pedons under long time cultivation in north regions. These developments were originated from organisms that grew under good drainage class. The smectite was seen in the south part of region. It may have been transported by river and deposited under high salinity and flocculated in contact to Persian Gulf’s saline water. The palygorskite was not seen in all patterns. This clay was removed in pedons under long time cultivation in the north area due to more leaching. High irrigation water can accelerate palygorskite transformation. Also, the XRD patterns showed that chlorite, illite, kaolinite and quartz were main clay minerals in the studied soils.
M. Noshadi, M. Jamaldini, A. Sepaskhah,
Volume 19, Issue 71 (6-2015)
Abstract
In this research, the hydraulic behavior of two kinds of envelopes including synthetic envelope, PP450 and gravel envelope with USBR standard in two soil tank models with silty loam texture was investigated. Three water heads including 55, 75 and 105 cm (water logging) from drain level were used. The discharge of pipe drain in the steady state condition for gravel envelope and at 55, 75 and 105 cm water heads was 188.9, 172.0 and 897.0% more than those in PP450, respectively. Envelope hydraulic conductivity rates at gravel envelope for 55, 75 and 105 cm water heads were 24.6, 14.0 and 21.2 times higher than those in PP450, respectively, and gradient ratios in these water heads for gravel envelope were 14.5%, 2.8% and 14.2% lower than those for synthetic envelope. There were also different behaviors in the two kinds of envelopes for hydraulic conductivity and entrance resistance of pipe and envelope in 55 and 75 cm water heads relative to 105 cm. In general, according to the measured parameters in this research, gravel envelope showed a better performance.
M. M. Matinzadeh, J. Abedi Koupai, H. Nozari, A. Sadeghi Lari, M. Shayannejad,
Volume 20, Issue 76 (8-2016)
Abstract
In this research, a comprehensive simulation model for water cycle and the nitrogen dynamics modeling including all the important processes involved in nitrogen transformations such as fertilizer dissolution, nitrification, denitrification, ammonium volatilization, mineralization, immobilization as well as all the important nitrogen transportation processes including nitrogen uptake by the plant, soil particles adsorption, upward flux, surface runoff losses and drain losses, was used for fertilizer management modeling in a sugarcane farmland in Imam Khomeini Agro-Industrial Company using a system dynamics approach. For evaluating the model the data collected from Imam Agro-Industrial Company equipped with a tile drainage system with shallow ground water and located in Khuzestan province, Iran, were used. The statistical analysis of the observed and simulated data showed that the RMSE for determining the accuracy of simulation of the nitrate and ammonium concentration in drainage water is 1.73 mg/L and 0.48 mg/L, respectively. The results indicated that there is good agreement between the observed and the simulated data. Nine scenarios of fertilization at different levels of urea fertilizer were modeled including one scenario of 400 kg/ha, two spilit scenarios of 350 kg/ha, two spilit scenarios of 325 kg/ha, two spilit scenarios of 300 kg/ha, one scenario of 280 kg/ha and one scenario of 210 kg/ha. Results of the modeling showed that the scenario of 210 kg/ha has the highest nitrogen use efficiency (52.3%) and the lowest nitrogen losses consisted of denitrification, ammonium volatilization and drainage losses (17.82, 7.16 and 92.59 kg/ha, respectively). The results revealed that increasing the consumption of urea fertilizer greater than 210 kg/ha increased the overall nitrogen losses and reduced the nitrogen use efficiency. Meanwhile, this model can be used for managing the fertilizer and controlling the nitrate and ammonium concentrations in the drainage water to prevent the environmental pollution. Also, the system dynamics approach was found as an effective technique for simulating the complex water-soil-plant-drainage system.
K. , and M. R. Nosrati, M. Amini, A. Haddadchi, Zare3,
Volume 20, Issue 78 (1-2017)
Abstract
Accelerated soil erosion in Iran causes on-site and off-site effects and identifying of sediment sources and determination of their contribution in sediment yield is necessary for effective sediment control strategies in river basin. In spite of increasing sediment fingerprinting studies uncertainty associated with magnetic susceptibility properties has not been fully incorporated in models yet. The objective of this study is determination of the relative contribution of sediment sources using magnetic susceptibility properties (High frequency, Low frequency and Frequency dependence) incorporated in uncertainty mixing model. For this purpose, 25 bed sediment samples were collected from the outlet of drainage basin and outlet of sub-basins and their magnetic susceptibility was measured and calculated. The results of Kruskal–Wallis test and discriminant function analysis showed that magnetic susceptibility properties can be used as optimum set of tracers in the uncertainty mixing model. The results of Bayesian mixing model indicated that mean (uncertainty range) relative contribution of Sparan, Joyband and Boyoukchay are 92 (83.9-94.8), 2.8 (0.2-10.7), 5.7 (0.2- 10.5) percent, respectively. According to these results, the highest amount of sediment yield is related to Sparan sub-basin and these results could be used in soil conservation and management planning.
Seyyed S. M. A. Maddahzadeh., K, Esmaili, B. Ghahraman,
Volume 21, Issue 1 (6-2017)
Abstract
Bi-level drainage system is a type of underground drainage systems, in which adjacent drainage lines are installed at different depths. In the Hydraulics Laboratory, Ferdowsi University of Mashhad, a model was built, that include a cube tank 2 meters in length, width and height of 1 meters was made of galvanized. In this model, two rows 20 cm apart from each other drains were installed. As drainage, a pipe of three layers to the outer diameter of 16 mm was made of PVC. Within this model of stratified soil was used as a soil layer of low permeability with a hydraulic conductivity of 1.15 cm per hour, thickness of 20 cm soil layer between two light soil layer with 30-cm thickness for bottom layer and 20 cm for the top layer with a hydraulic conductivity of 1.55 cm per hour. For accurate measurement of the water table Behavior in the soil at each point of the model, some piezometer distance of 10 cm from each other on the floor model was installed. After Outfit of model with blow-off valve, Experiments with a heavy irrigation for different intervals between depths of 30 and 50 cm were used in drainage and water table elevation values as observed values were extracted from the model. The results show that the values obtained from Upadhyaya and Chauhan Equation only in small area of water table profiles, which include an area of between the two drainage, are consistent with observed and with a wider distance between deep and shallow drainage, time of drop in water table increased.
M. Golabi, M. Albaji, A. Naseri,
Volume 21, Issue 3 (11-2017)
Abstract
In the present study Hydrus-1D software was used to simulate electrical conductivity, pH and sodium, potassium, calcium, magnesium, chloride and sulfate ions. Field experiments were performed at the Sugarcane Research Center located in south of Ahvaz on sugarcane varieties CP48-103 with four water treatments (one treatment was Karun river water and three treatments were diluted drainage water) and three replications. The samples were collected from 0-30, 30-60 and 60-90 cm soil depth before irrigation and electrical conductivity and anions and cations of soil were measured in the laboratory. Sensitivity analysis and calibration were first performed with the aim of verifying the Hydrus-1D software. The sensitivity analysis indicated that the software had maximum sensitivity to the saturated volumetric water content. Minimum sensitivity was for the inverse of the air-entry suction, tortuosity parameter, residual volumetric water contents and moderate sensitivity was for hydraulic conductivity at natural saturation. Also, the software did not show any sensitivity to empirical parameter related to the pore size distribution that is reflected in the slope of water retention curve. In calibration stage the amount of hydraulic conductivity at natural saturation, residual volumetric water contents, saturation volumetric water contents, the inverse of the air-entry suction, empirical parameter related to the pore size distribution and tortuosity were obtained as 18 (cm/day), 0.04 (cm3/cm3), 0.63(cm3/cm3), 0.012 (cm-1), 1.2 and 0.6 respectively. The results showed that the coefficient of determination of all parameters was more than 0.85 which confirms the appropriate capabilities of the model in simulation of electrical conductivity, pH, anions and cations. In the modeling carried out the amount of NRMSE was between 11 and 18 percent which indicates good performance of the model. The Nash-Sutcliffe efficiency criterion was obtained 0.72 to 0.8 that indicates a good match of the model with reality. The coefficient of residual mass in this paper was positive for electrical conductivity, pH and sodium, potassium, calcium, magnesium and negative for chloride and sulfate. The positive and negative coefficient of the residual mass shows less and over estimation of the model.
Y. Abdoli, S. Jafari,
Volume 22, Issue 1 (6-2018)
Abstract
This study was done to evaluate the effect of topography, water table, and irrigation on gypsc soil development and clay mineral diversity in Ram-Hormuz Plain, Khuzestan Province. To localize, 10 profiles in this region that covered all purpose irrigation and topography situation were described. The results showed that the soils could be classified in Entisols, Inceptisols and Aridisols orders. All soil epipedons were ochric and subsurface horizons were cambic, gypsic, and salic. The salic horizons were formed under a low water table. The XRD results showed that smectite, kaolinite, illite, chlorite, palygorskite, vermiculite and sepiolite were the dominant minerals, respectively. Kaolinite and illite were inherited from the parent material, but chlorite was the result of both inheritance and transformation of other clay minerals except uncultivated or non-irrigated soils. Sepiolite was decreased in gypsic horizons, but palygorskite was increased in these horizons. Sepiolite was raised with increasing the depth under the good drainage class; this could be related to neoformation, but it was decreased with depth under the weak drainage class. These results could be due to the instability of this mineral in high moisture and its low Mg activity. There was also a negative correlation correlation between Palygorskite and smectite; this was such that most palygorskite was observed in the surface horizons, but smectite was in the subsurface. Smectite was the dominant clay mineral in the studied soils; it was formed from the weathering of other minerals as well as from neoformed ones in the lowlands. Vermiculite was formed in these soils due to k depletion by leaching or plant absorption. This happened in the illite to smectite transformation process. Therefore, topography and irrigation could be regarded as the main factors putting these soils in high category; also, clay mineral assemblage was different under this situation in these soils.
M. Noshadi, S. Karimi,
Volume 22, Issue 3 (11-2018)
Abstract
The growth of world population and the demand for agricultural products can be regarded as one of the important issues that humanity has ever faced. There are serious concerns regarding surface and ground water pollution by nitrates because of using nitrogen fertilizers in the agriculture. Improving agricultural water management systems can reduce nitrate in drainage outflow and therefore, reduce the environmental pollution. This research was conducted to evaluate the effect of the controlled drainage and nitrogen fertilizer on nitrate leaching and environment pollution as a factorial randomized complete block design in Shiraz College of Agriculture. The treatments consisted of three fertilizer levels; 0, 200 and 300 kgN/ha, and three water table depths: free drainage, control water table at 60cm (CD60) and 90 cm (CD90) depths, respectively. According to the results, the value of drainage water and nitrate losses in the controlled drainage toward free drainage were significantly increased. The mean reduction of drainage water in CD60 and CD90, as compared to free drainage, was 59.3 and 35.7%, respectively. The decrease nitrate losses, as compared to free drainage, was 72 and 44%, respectively. The total value of nitrate leaching in 200 and 300 kgN/ha fertilizer treatments was 1.86 and 2.48 times of 0 kgN/ ha.
M. R. Mirzaei, S. Ruy,
Volume 22, Issue 4 (3-2019)
Abstract
Preferential flow is of great importance in the environment and the human health. So, rapid water transportation and consequently, pollutants and pesticides leak out and get into the groundwater, making it very difficult to measure and quantify. To quantify and describe the preferential flow, two gravity-driven models were used: 1) kinematic wave model (KW) introduced by Germann in 1985), and 2) kinematic dispersive wave (KDW) model developed by applying a second-order correction to the Germann’s model by Di Pietro et al. in 2003. So, the experimental data was obtained using the laboratory mini-rainfall-simulator over cylindrical soil samples at the laboratory. Their parameters were obtained using Solver add-ins in the Excel software. Then, the results were compared using the root-mean-square error (RMSE). The results showed that the KDW model could better predict the preferential flow (with lower RMSE). Also, the regression results showed 1) there was no significant relation between the preferential flow and the total porosity, and 2) there is a significant relation between the preferential flow and the macrospores.
M. M. Matinzadeh, J. Abedi Koupai, A. Sadeghi-Lari, H. Nozari, M. Shayannejad,
Volume 23, Issue 3 (12-2019)
Abstract
Selection of drainage equation with acceptable accuracy has always been a challenge for designers to design subsurface drainage systems. In this research, seven steady state drainage equations were used for predicting daily and cumulative drainage rate on a farmland of sugarcane in Imam agro-industrial Company. These drainage equation included Hooghoudt, Ernst, Kirkham and Dagan that have been developed in the past and Mishra and Singh, Henine and Yousfi et al that recently developed. The statistical indices consist of P-value, RMSE, R2 and Percentage Error of estimating cumulative drainage rate were calculated for Hooghoudt equation 0.9501, 1.49 (mm/day), 0.80 and -0.19%, respectively. For Ernst equation 0.0001, 2.46 (mm/day), 0.34 and 16.98%, respectively. The result of performance of drainage equations revealed that Hooghoudt and Ernst equation were as the equations with the highest and lowest accuracy in predicting drainage rate, respectively. Also from the newly developed equations, the Yousfi et al equation was found with relatively well accuracy to predict the drainage rate. This equation was placed in second rank after Hooghoudt equation and other equations showed poor performance. Thus, with selection of the appropriate drainage rate, the Hooghoudt equation is suggested for designing of drain spacing in medium to heavy textured soils such as sugarcane agro-industrial.
S. Janatrostami, A. Salahi,
Volume 25, Issue 2 (9-2021)
Abstract
Water allocation needs to adhere to the principles of efficiency, equity, and sustainability, but, equity usually is less considered. Foumanat irrigation area with five command areas is one of the three areas of Sefidroud irrigation and drainage network that more than 90% of it is covered by paddy fields. Since water plays a key role in paddy fields, the lack of uniform distribution of water resources throughout the irrigation area during the rice cultivation period causes irrigation water scarcity and severe damage to some irrigation areas. In this study, the equity of groundwater withdrawal and the received surface water from Sefidroud irrigation and drainage canals according to the shared water resources among Foumanat’s command areas were evaluated using the Gini coefficient. Therefore, a water allocation optimization model was developed to maximize the equity in the allocation of groundwater and surface water of canals according to the minimum current economic benefit in the command areas. The results showed that in optimum conditions, the equity of groundwater and surface water resources allocation was increased by 46.3% and 43.7%, respectively. The evaluation of the optimal allocation of available water resources also showed that the amounts of groundwater withdrawal and the received surface water from canals are distributed equally among command areas.
M. Pakmanesh, H. Mousavi Jahromi, A. Khosrojerdi, H. Hassanpour Darvishi, Hossein Babazadeh,
Volume 25, Issue 3 (12-2021)
Abstract
The present study is investigated the earth dam stability during drawdown based on both numerical and experimental aspects. To validate the numerical model, a model was performed experimentally. Some soil mechanic tests were carried out through the hydraulic experiments to attain the usage factors of the numerical investigation. To investigate the effect of hydraulic conductivity on the rapid drop of water level and the use of hydraulic parameters of materials, seepage flow in the model was modeled by seep/w software. The input information to the software including hydraulic conductivity and water volume were measured by performing a constant load test and using a disc penetration meter, respectively. After validation of hydraulic conductivity with the experimental model, the results were compared with observed data. Comparison between numerical and laboratory discharge illustrated that the numerical model with laboratory model is well confirmed. In addition, saturated and unsaturated simulations demonstrated that the unsaturated model is highly consistent with the experimental model. It is assumed that due to the drawdown conditions, unsaturated models can achieve high accuracy for simulating the flow through a homogeneous earth dam.
A. Malekian1, A.a. Jafarazdeh, Sh. Oustan, M. Servati,
Volume 26, Issue 2 (9-2022)
Abstract
To study the soil-landscape change in the Chaldoran region, 9 representative soil profiles were studied in 5 dominant geomorphic units of the study area including piedmont plain, mantled pediment, alluvial fan, plain, and flood plain. The results showed that the accumulation of pedogenic carbonate in some soils was concretion and light in color. In control soils in the piedmont plain (profile 5 and 7), mantled pediment (profile 6), and flood plain (profile 8) clay transferred from the surface horizons and accumulated in the lower horizon, due to relatively good rainfall in the region and distinct dry and wet seasons has led to the formation of argillic horizons along with the formation of crust on the surfaces of aggregates and building units and has formed the Alfisoils order. Mineralogical results showed the presence of chlorite, illite, kaolinite, and smectite minerals. According to the evidence, illite, chlorite, and kaolinite minerals were inherited and smectite minerals were formed due to weathering and evolution of illite, chlorite, or palygorskite minerals. Also, the results of the CIA index in the region indicated that the soils of the region are in the stage of weak to moderate weathering. In general, the results indicated the critical role of drainage, land use, and parent materials in the soils of the study area.
Y. Esmaeli, F. Yosefvand, S. Shabanlou, M.a. Izadbakhsh,
Volume 27, Issue 2 (9-2023)
Abstract
The objective of the current study was to zone flood probability in the Marzdaran watershed. Since the allocated budget for management work is limited and it is not possible to carry out operations in the whole area, having a map that has prioritized different areas in terms of the probability of flood occurrence will be very useful and necessary. A well-known data mining model namely MaxEnt (ME) is applied due to its robust computational algorithm. Flood inventories are gathered through several field surveys using local information and available organizational resources, and the corresponding map is created in the geographic information system. The twelve predisposing variables are selected and the corresponding maps are generated in the geographic information system by reviewing several studies. The area under the curve (ROC) is used to evaluate the modeling results. Then, the most prone areas of flood occurrence which are prioritized for management operations are identified based on the prepared map. Based on the results, about 100 km2 of the study area is identified as the most prone area for management operations. The results showed that the accuracy of the maximum entropy model is 98% in the training phase and 95% in the validation phase. The distance from the river, drainage density, and topographic wetness index are identified as the most effective factors in the occurrence of floods, respectively.
A. Shahnazari, S. Sadeghi,
Volume 27, Issue 2 (9-2023)
Abstract
In the present paper, crop pattern criteria have been evaluated relying on sustainable development to increase agricultural water productivity. Seven criteria were selected as the main environmental and economic criteria and were prioritized and reviewed for important and strategic products in the Tajan catchment of Mazandaran province. Criteria prioritization was done using optimization through a genetic algorithm with an objective function based on sustainable development. Then, physical and economic productivity indices were calculated to determine the productivity value. Based on the results, in the selection of the crop pattern, firstly, the category of economic criteria and finally the category of environmental criteria have been given attention to the farmers in the current situation. But in the genetic optimization algorithm, all priorities have a similar order from the environmental point of view and then from the economic point of view although each product has its order of criteria. By this prioritization, the parameters of the cultivated area, the volume of water consumed, and the amount of chemical fertilizers have decreased on average by 26%, 34%, and 21%, respectively, and the parameters of product performance and profitability have increased by 43% and 61%, respectively. In addition to providing environmental standards and increasing sustainable development, this prioritization causes an average increase in physical productivity by 84% and an increase in economic productivity by 72%.
