Search published articles


Showing 4 results for Hydraulic Structure
Study of Labyrinth Spillways with Curved Planform
M. Yasi, M. Mohammadi,
Volume 11, Issue 41 (10-2007)
Abstract

  A labyrinth spillway is an overflow spillway to regulate and control flow in canals, rivers and reservoirs. The main hypothesis for the development of such a spillway is to increase the discharge per unit width of structure for a given headwater. This type of structure is often an efficient alternative to a gated-spillway type where either the increase of the flood-passage capacity or the control of the water surface upstream is concerned. This study was aimed to investigate the hydraulic performance of labyrinth spillways of general trapezoidal planform with simple curved apexes. In the experimental work, twelve spillway models with double cycles were considered using three different curved apexes (R/w= 0.15, 0.2, 0.25), each with four different crest heights (w/P= 1.5, 2, 3, 4). Based on the cited recommendations, the length magnification was set to a constant ratio of (l/w= 3) the crest shape was to be of a semi-circular form with simple radius (r= 15 mm) and the spillway walls were vertical with the thickness of T= 2r. An intensive experiment was carried out over a wide range of flows, providing 720 flow data ranging from free flow to submerged flow conditions. 1D flow equation was presented using combined mathematical and dimensional analysis. A coefficient of discharge, Cd, was introduced to represent the influence of the effective geometric and hydraulic parameters on the flow capacity over the spillway. Modular limit was also controlled to see whether the flow over the spillway would be submerged. The results of the study indicate that the modified curved planform of the spillway apexes with consistent divergence in the downstream channel introduces a significant improvement in the flow efficiency over the labyrinth spillways. Spillways with narrower curved apexes (i.e. R/w≤ 0.2), and with the vertical-aspect ratio of (2≤w/P<3) provide more stable and higher hydraulic performance than any other labyrinth planforms over a wide range of flows (i.e. 0.10/P<0.6). In terms of the flow capacity, the proposed spillway model is shown to be more efficient than other zig-zag planforms (i.e. triangular and trapezoidal shapes) with an identical crest length.


Experimental Comparison of Energy Dissipation on Drop Structures
A. Moradi Sabz Koohi, S. S.m. Kashefipour, M. Bina,
Volume 15, Issue 56 (7-2011)
Abstract
Drops are the most important and common hydraulic structures used as energy dissipators in irrigation networks and erodible waterways. Dissipation of energy occurs in two different ways. One portion belongs to the geometric form of the structure (briefly called loss due to structure), whereas the other occurs due to happening of hydraulic jump downstream of the structure. The dimensions of drop structure and downstream stilling basin can be optimized if geometric and hydraulic characteristics are recognized properly. In this research, the effects of drop geometry and hydraulic characteristics on the loss due to structure were investigated. At first, the effective dimensionless parameters were specified. 14 physical models of more common drops including straight, inclined and stepped drops were then built in 2 heights of 51.5 & 25.5 centimeters and 2 bed slopes of 26.6 & 33.7 degrees. The number of steps in stepped models was chosen equal to 3 and 7. With establishment of 90 flow rate, the energy losses were compared. The results showed that in the range of variable parameters, the straight drop has the maximum amount of energy dissipation.
Optimization of the Drain Position to Reduce the Uplift Force in the Foundation of Dams
S. Salehi, Sh. Esmael Zade, Gh. Panahi, K. Esmaili,
Volume 22, Issue 4 (3-2019)
Abstract
The effect of the uplift force in the hydraulics structures is against stability. So, determining and controlling this force can be very important. One of the ways to achieve this purpose is to decrease this force by using the hole drains; in this way, we can build perpendicular pipes with different diameters, leading to the durability of the structure. Therefore, an experimental model of concrete dam was constructed in the hydraulic laboratory. The dam's model was divided into five sections by using 4-hole drains with a thickness equal to the dam's foundation. By running experiments with the maximum water level at the upstream, dam hole drains were opened in their position. Hydraulic potential was estimated by using the Piezometer built in the flume body. Finally, by opening some hole drains, the uplift force was calculated from the equipotential lines. Therefore, the best case (which had the minimum force) was determined, which was a/L=0.4, to create the most proper hole drain in the dam foundation. (a: distance of drain to heel and L: length of the dam's foundation). To place the hole drain in this position, by applying the zero potential in this position, the up lift force was increased

Experimental Study of Discharge Coefficient at the Dentate Trapezoidal Labyrinth Weir
J. Meshkavati Toroujeni, A.a. Dehghani, A. ٍemadi, M. Masoudian,
Volume 25, Issue 3 (12-2021)
Abstract
One of the crucial problems that exist in the irrigation networks is the fluctuation of the water surface flow in the main channel and changes in the flow rate of the intake structure. One of the effective methods to decrease these fluctuations is increasing the weir crest length at the given width of the channel with the use of the labyrinth weirs can be achieved for this purpose. The labyrinth weir is the same linear weir that is seen as broken in the plan view. In this study, a labyrinth weir with a length of 3.72 m, three different heights of 15, 17, and 20 cm, three different shapes of dentate (rectangular, triangular, and trapezoidal), and a linear weir were used in a recirculating flume with 15 m length and 1 m width. The result showed that for a given length and height of weir, with the increasing of the upstream water head to the weir height ratio (), the discharge coefficient decreases. The results showed that by increasing weir height, the discharge coefficient decreases for a given length of the weir. Linear weir and labyrinth weir without dentate create more water depth at the upstream by 3.3 and 1.2 fold compared with dentate labyrinth weir.

Page 1 from 1     

© 2024 CC BY-NC 4.0 | JWSS - Isfahan University of Technology

Designed & Developed by : Yektaweb