Showing 6 results for Side Weir
T. Honar, M. Javan, A. Keshavarzi,
Volume 6, Issue 3 (10-2002)
Abstract
Side weirs as flow diversion devices are widely used in irrigation, land drainage and urban sewage systems. In the present study, the effects of the length and height of inclined side weir crest on discharge coefficient were investigated in prismatic and nonprismatic rectangular channels.. In this study, 675 laboratory tests were conducted.
Analysis of experimental tests showed that the discharge coefficient is strongly correlated with uptream Froude number, height of weir to depth ratio at upstream of weir, ratio of water depth on weir to length of weir, and with prismatic factor. Based on experimental results, a model is proposed. The model is capable of estimating the discharge coefficient under subcritical flow conditions. Finally, the data from the proposed model was compared with those obtained by other researchers under different side and bed slopes. There was a good agreement with a relative error of less than ten percent.
E Izadi, M Heidar Pour, A Kabiri Samani,
Volume 12, Issue 46 (1-2009)
Abstract
In this study, the flow characteristics have been investigated by measuring separation zone, surface and velocity profiles over the circular crested side weirs. An equation was proposed for the length of the separation zone using dimensional, statistical and regression analysis. The dimensional analysis showed that the length of separation zone depends on the upstream to the downstream water depth over the side weir, channel width to the downstream water depth and the Froude number. Comparison of the longitudinal and sectional surface profiles showed that the surface profiles at the vicinity of the side weir are non-uniform, due to separation zone close to the side weir. Therefore, the suitable place for measuring the characteristics of flow is along the centre line of the channel. It was observed that the maximum velocity occurred below the surface water which might be due to the secondary flow around the side weir. By increasing the distance far enough from the side weir, the effects of secondary flow were minimized and the velocity profiles tended to be uniform.
A Karizi , T Honar ,
Volume 14, Issue 51 (4-2010)
Abstract
Side weirs as flow diversion devices are usually used as emergency weirs in large hydraulic structures like dams and irrigation and drainage networks, because of their importance they require delicate design. As a result application of numerical and simulation models play an important role in design of these hydraulic structures. In this research, the flow pattern and shear stress distribution on broad crested side weirs with different widths and entrances along with different discharges were studied by numerical solution under two and three dimensional conditions and then the results were compared with laboratory findings. These experiments were conducted in a rectangular channel with one side weir and a length of 70 cm. Experiments were done considering rounded and sharp entrances with different rounded radii and one constant discharge with intake proportions of 40 and 60 in main and branch channels, respectively. Comparison of numerical solution and experimental results show that side weirs with rounded entrance had a noticeable shear stress reduction (arrived in the bed and sides) and non-effective spinal flow, resulting in increased intake efficiency.
T. Honar, S. Mazloom Shahraki,
Volume 18, Issue 69 (12-2014)
Abstract
Cylindrical and semi-cylindrical weirs are used in water distribution systems for flow measurement in open channels and for control of water surface. Review of literature shows that cylindrical and semi-cylindrical weirs are not widely used in practice. Because of their low construction cost and simplicity, an investigation was done to study cylindrical and semi-cylindrical weirs in terms of their hydraulic characteristics such as discharge coefficient, energy loss and flow depth over the spillway crest. The research was done for 128 models in the hydraulic laboratory of water engineering department, Shiraz University. According to the results, due to flow separation from body of the weirs, flow coefficient increases in the cylindrical and semi cylindrical weirs by 57%. It was found that discharge coefficient increases by increasing the total head of upstream. Therefore, construction of cylindrical and semi-cylindrical weirs and side weir is recommended due to reduction in weir length, increased hydraulic efficiency, and reduced administrative costs compared to other wide edge side weirs.
S. Samiee, M. Heidarpour, S. Okhravi,
Volume 19, Issue 73 (11-2015)
Abstract
Side weir is the structure to evacuate extra water from a canal when level of water rises. This structure is mounted on the wall of canal. It is used predominantly to set flow in irrigation and drainage systems or urban wastewater harvesting systems. Implementing guide vanes is a simple way to increase side weir efficiency. In this study, the effect of using guide vanes on discharge and discharge coefficient of rectangular sharp-crested side weirs was investigated. ADV instrument was applied for recording vertical velocity over the crest of side weir. Local discharge was calculated by vertical velocity data for both conditions of presence and no presence of guide vanes. Results showed that in both cases, increasing the Froude number results in the decrease of passing discharge and discharge coefficient of the rectangular sharp-crested side weir. Data analysis also showed that by increasing the Froude number, guide vanes have more effect on increasing discharge coefficient and local discharge. The local discharge increased along the crest and the most passing local discharge occurred near the end of the side weir. Analysis indicates that using guide vanes leads to the increase of discharge coefficient by about 32%.
M. Neisi, M. Sajadi, M. Shafai Bejestan, J. Ahadiyan,
Volume 28, Issue 3 (10-2024)
Abstract
Side weirs are hydraulic structures employed in irrigation and drainage channels as diversion devices or head regulators. The increasing efficiency of the structure of side weirs for constant head has been one of the concerns of researchers in the last decade. The use of different forms of sharp crest, labyrinth, piano key, and increasing the length of the overflow by changing the geometry of the crest have been investigated. In this research, a new type of triangular-shaped side weir has been studied in the laboratory under different hydraulic conditions in sub-critical flow conditions. The results demonstrated that by inclining the crests of the triangular side weir, the amount of vortex created at the entrance of the opening was reduced. So the discharge coefficient and the flow volume over the side weir showed an increase of up to 27% and 48%, respectively, compared to the normal triangular and rectangular side weirs. Also, after analyzing the data, a non-linear equation was presented to estimate the discharge coefficient with the dimensionless parameters of the ratio of the upstream depth to the weir height (y1/p) and the upstream Froud number (Fr1) with an accuracy of ±15% and NRMSE=0.134.
