Showing 4 results for Submergence
S. M. A. Zomorodian, M. R. Bagheri Sabzevari,
Volume 9, Issue 4 (1-2006)
Abstract
The vertical pipe intake is an economical structure relative to the other alternatives. VPI usually installed near the water surface and prevents from the coarse sediment entrance to the system. The strong vortex in VPI entrance is a major problem which may reduce the system efficiency. Recognizing the vortex affected parameters, helping engineers to design anti vortex structures. In this study an experimental model is built to study the effect of tangential velocity, flow direction at approach channel outlet on the discharge coefficient of vertical pipe intake. By dimensional analysis it is indicated that the vortex in VPI could be defined by the dimensionless numbers (Reynolds, Weber, Froude, Circulation and Submergence). The relationship between the Froude, Circulation and Submergence numbers are presented. By using this relation one can determine the Submergence number and then calculate the discharge coefficient of vertical pipe intake.
A. A. Kamanbedast, S. R. Mousavi,
Volume 20, Issue 78 (1-2017)
Abstract
Morning glory spillway is one of the spillways and used when it is not possible to use any other spillways. With the onset of submergence and flow loss, and intensification of circulation and vortexes, spillway performance decreases severely. With decreasing discharge coefficient, the height of water in the reservoir increases and the risk of dam damage, caused by the lack of spillway ability of great flow discharge, increases. Anti-vortex piers are used to solve this problem. The increase of the submergence threshold can provide ability of greater flow discharging, without spillway submergence and its negative consequences. Anti-vortex piers, in addition to correcting circulation and vortexes, may also be effective in increasing the submergence threshold. To investigate this possibility, 110 experiments were performed with the physical model on spillways with square and circular inlet section in different modes and number of anti-vortex piers. Results show that increasing number of Anti-vortex piers increases the submergence threshold and spillway can discharge greater inflow and height of water without being submerged. The effect of the overflow of the circle shape, because currents and vortexes spinning in a circle overflow is higher than square spillway. Also the maximum discharge coefficient was observed when 4 vortex breakers were installed at the angle of 90 degrees.
H. Elahifar, O. Tayari, N. Yazdanpanah, M. Momeni,
Volume 25, Issue 4 (3-2022)
Abstract
The discharge coefficient of labyrinth weirs increases with increasing the crest length in a certain width range. The present research was carried out in a laboratory flume with a length of 8 m, a width of 0.6 m, and a height of 0.6 m. The discharge coefficient of two-cycle symmetric and asymmetric rectangular labyrinth weirs was experimentally measured. The dimensional analysis by the Buckingham π theorem indicated that the discharge coefficient was dependent on Se, B/Wavg, Ht/P, and WL/WR. According to the results, the discharge coefficient decreased with increasing the hydraulic head in the symmetric and asymmetric labyrinth weirs and the linear weir. Asymmetric labyrinth weirs with a WL/WR of 2.05 outperformed symmetric labyrinth weirs with a WL/WR of 1. Quantitatively, the discharge coefficient of the labyrinth weir with a B/Wavg of 3.1 was respectively 21% and 94% higher than that with a B/Wavg of 2.93 and 2.76. The discharge coefficient of the labyrinth weir with a WL/WR of 2.05 was 10-27% higher than that with a WL/WR of 1. The discharge coefficient of the linear weir was 60-250% higher than that of labyrinth weirs.
M. Sabouri, A.r. Emadi, R. Fazloula,
Volume 26, Issue 2 (9-2022)
Abstract
A compound sharp-crested weir is often used to measure a wide range of flows with appropriate accuracy in open channels. In this study, experiments were performed to investigate the hydraulic flow through a compound weir of circular-rectangular with changes in hydraulic and geometric parameters in free and submerged flow conditions. The characteristics of the weirs include rectangular spans width of 39 cm, a circular radius of 5, 7.5, and 12.5 cm, and heights of 10 and 15 cm. The results showed that by increasing the radius and height of the Weir, upstream water depth increases around 28.4%. At a constant h/p, the discharge coefficient increases with the increasing radius of the circular arc. Also, in the submerged conditions, the discharge coefficient is less (around 40%) than in the free flow condition, which is due to the resistance of the depth of the created stream against the passage of the flow.
