Showing 26 results for Tillage
M. A Hajabbasi, A. F Mirlohi, M. Sadrarhami,
Volume 3, Issue 3 (10-1999)
Abstract
A two-year study (1996-97) was conducted to verify tillage effects on several soil properties and corn yield. The soil (fine loamy, Thermic, typic Haplargids) was treated by conventional (CT) and no-till (NT) systems. Soil organic matter (OM), mean weight diameter (MWD), penetration resistance (Cl), bulk density (BD), total nitrogen (TN) and aggregate size distribution at depths of 0-20 and 20-40 cm were measured.
No-till system caused the OM to be twice as much as that in the conventional tillage system. Total nitrogen in the NT and at depths of 0-20 and 20-40 cm were higher by 30% and 20%, respectively. No differences obtained in bulk density and penetration resistance, but MWD in the NT was 20% and 10% higher than CT in the 0-20 and 20-40 cm depths, respectively. Mean weight diameter of the aggregates in the CT was smaller than that in NT. Aggregates of less than 0.25 mm at 0-20 cm depths were almost 25% higher in CT compared to NT system. The yield in the NT system was significantly lower than CT. Although reduced cultivation could bring a better soil physical condition, low initial organic matter, weak structure and heavy-textured soil produced unsuitable conditions for the crop roots and, consequently, resulted in low yield. Therefore, no-till system in this region would not be recommended.
M.r. Mosaddeghi, M.a. Hajabbasi, A. Hemmat, M. Afyuni,
Volume 3, Issue 4 (1-2000)
Abstract
Soil structure maintenance and stability is an important index indicating sustainable soil management. In this regard, components such as soil moisture and organic matter affect soil compactibility during farm machinery trafficking. Soils in Central Iran are commonly very low in organic matter (OM) and thus susceptible to compaction. This study was conducted to measure the effects of soil moisture content and manure application on soil compactibility. A randomized complete block design with four blocks (replicates) with the treatments nested (split-block) into the blocks was used in the soil (Typic Haplargids), located in Isfahan University of Technology Research Farm (Lavark). One-year aged manure treatments 0, 50, and 100 t ha-1 were incorporated into soil up to the tillage depth (20 cm) by a heavy disc. After five months (July-November), a two-wheel-drive tractor Universal Model U-650 was passed through the field at soil moisture contents of plastic limit (PL), 80% PL (0.8PL), and 60% PL (0.6L), either once (P1) or twice (P2). Bulk density (BD), cone index (CI), and soil sinkage (S) were measured as indices of soil compactibility and trafficability. Adding manure countered the effects of load and wetness on BD and CI, significantly. There was a significant difference between the effects of 50 and 100 t ha-1 of manure on BD but not on CI. Manure application reduced soil sinkage at high moisture contents (PL) but increased it at low moisture contents (0.6PL). Adding manure also reduced the BD and CI of subsoil. Repeating the passage of tractor (P2) increased compaction significantly. The significant increase in BD and CI did no occur at 0.6PL. When no manure was applied even at 0.6PL, there were limitations for trafficability, whereas this limit for 50 t ha-1 treatment was reached at 0.8PL. Results from this study indicate that the manure application at a rate of 50 t ha-1 reduces soil compactibility and increases soil moisture trafficability range.
A. Mirlohi, M.a. Hajabassi, S.j. Razavi, E. Ghanaati,
Volume 5, Issue 1 (4-2001)
Abstract
Soil loss due to erosion is a common problem in most parts of Iran. Reduced soil organic matter and lack of proper agricultural management have intensified the problem in recent years. Conservation tillage systems are becoming more widely used in corn production in other parts of the world because of soil losses due to wind and water erosion and energy inputs. Changes in tillage methods, however, create different environments for the germination, development and maturation of corn plants. Most corn hybrids have been selected and developed under conventional tillage systems but these hybrids mayor may not be well adapted to both systems. This study aims to evaluate the performance of five locally grown corn hybrids under zero and conventional tillage methods. The experiment was conducted for 2 years on a plot of land specified for this study. Experimental design was a split plot with randomized complete block arrangement and four replications.
Seedling and juvenile plant growth were not affected by tillage method and were similar for all hybrids. Plant dry matter was affected significantly by the cropping system and was lower in no-till method. Plant leaf area index and stem diameter reduced significantly in the no-till system. Reduction was greater in the second year of the experiment. Also grain yields were significantly different among years, tillage method and plant genotypes. Yield reduction was highest in the second year of the experiment under no-till cropping system. There was no interaction between tillage method and corn genotypes, indicating that, usually genotypes perform similarly with regard to grain yield under both tillage methods. The results suggest that corn production under no-till system in Isfahan is probably associated with yield reduction.
M. Afyuni, M.r. Mosaddeghi,
Volume 5, Issue 2 (7-2001)
Abstract
Tillage system effect, Conventional (CT) vs. No-Till (NT), on soil physical properties and Br transport was studied at two locations in North Carolina. The soil types were a Typic Paleudults at Coastal Plain (site 1) and a Typic Kanhapludults at Piedmont (site 2). Bulk density (BD), total porosity (TP), macroporosity (MP), and saturated hydraulic conductivity (Ks) .were measured in plant row (R), and trafficked (T) and untrafficked (N) interrows. A rainfall simulator was used to apply two early season rainfalls to 1 m2 plots where KBr suspension was surface applied for Br leaching study. The first simulated rainfall event (30 min) consisted of a low (1.27 cm h-1) or a high (5.08 cm h-1) rate applied, 24 h after Br application. One week later, the high rainfall rate was repeated on all plots.
Soil samples were taken two days after applying first and second simulated rainfall (a week between them) and the end of season from different depths for measuring Br concentrations. Soil physical properties were affected by both tillage system and position.
Bulk density was higher in NT versus CT and in T position versus Rand N positions. Total porosity was lower in NT versus CT but MP was significantly higher in NT. Saturated hydraulic conductivity was about 90% lower at T position versus N and R positions. Coefficient of variation was quite large, making it difficult to obtain statistical differences between tillage systems. The surface l0-cm of soil contained the highest Br concentration for depth treatments with treatment differences occurring primarily in 0 to 25 cm depth. In first and second sampling dates, more Br leached under NT versus CT system. However, there was no significant difference between the two tillage systems in Br leaching at the end of the growing Season. In site 1, Br leached more due to the coarse texture and high Ks of the soil.
N. Sakenian Dehkordi, B. Ghobadian, S. Minaei,
Volume 5, Issue 2 (7-2001)
Abstract
A suitable instrument capable of inserting mulch into soil is needed to improve soil water holding capacity. The goal of this research is to design and manufacture an instrument with a blade and mechanism that can insert rice mulch into the soil. All the parameters in sub-soiling operation were taken into account, and the technique presented can be recommended as a special method of injecting rice husk. The instrument designed was easy to use on a tractor. Sub-soiling operation and husk injection were carried out satisfactorily using various amounts of husk and at different soil depths. This method was added to the conservation chart presented by Morgan as an integrated technique.
F A. Frouzandeh Shahraky, M. R. Khajehpour,
Volume 9, Issue 4 (1-2006)
Abstract
Under irrigation and in double-cropping system, a large amount of plant residue remains after harvest that along with the limited time for residue decomposition and complete seedbed preparation, necessitates reduced tillage and special residue management. In the present study, the effects of various seedbed preparation methods on vegetative growth, yield components and seed and oil yields of sunflower (Euroflor hybrid) were studied in a barley-sunflower cropping system during 2001 at the Agricultural Research Station, Isfahan University of Technology. Three residue management treatments (standing, partly removed and burned) along with five tillage systems (moldboard + disk chisel + disk disk moldboard and furrower as the minimum tillage) were laid out in a split-block design with three replications. Burning residue treatment significantly increased plant dry weight at various developmental stages and also head diameter. Number of seeds per head, 1000 seed weight, harvest index, and oil yield were non-significantly higher in the burned residue treatment. Seed yield was significantly higher in the burned and partly removed residue treatments. Moldboard + disk and chisel + disk treatments significantly produced higher plant dry weight at various developmental stages, head diameter and seed yield. Number of seeds per head, 1000 seed weight, harvest index, and oil yield were non-significantly higher in these treatments. Minimum tillage ranked the lowest for these traits. The results of this experiment indicate that chisel + disk treatment with the partly removed residues might be an appropriate seedbed preparation method in a barley-sunflower double planting under conditions similar to this experiment.
A. Safadoust, M. R. Mosaddeghi, A. A. Mahboubi, A. Nouroozi, Gh. Asadian,
Volume 11, Issue 41 (10-2007)
Abstract
The increased potential for soil erosion and compaction due to continuous row crop production and intensive tillage is causing some concern and has led to the consideration of reduced tillage techniques as part of the solution. The objective of this study was to investigate the short-term (one-year) influences of different management practices on the physical properties of a sandy loam soil under corn crop. Treatments were the combinations of three tillage systems (no-till, NT chisel plow, CP and moldboard plow, MP) and three composted cattle manure rates [0, 30 and 60 ton (dry weight) ha-1]. The experiment was carried out in a split-plot design. Three replicates of the treatments were applied in a randomized block design. Saturated hydraulic conductivity (Ks), total porosity (TP), macro-porosity (Macro-P), micro-porosity (Micro-P) of soil and mean weight diameter (MWD) of aggregates, were measured to a depth of 22.5 cm when 100 percent of the tassels appeared. Tillage and manure combination had significant effects on Log[ Ks], TP, Macro-P and Micro-P. The MP system increased pore space and continuity due to complete inversion and loosening, and as a result Ks, TP, Macro-P and Micro-P were higher than NT system. Higher Macro-P observed for CP might have caused higher Ks versus MP. Reduced tillage systems increased MWD and the increment of manure caused an increase in MWD over all tillage treatments. The results indicate short-term positive effects of manure application on soil pore size characteristics and aggregate stability under moldboard and chisel plowings in the region.
H. Bayat, A.a. Mahbobi, M.a. Hajabbasi, M.r. Mosaddeghi,
Volume 11, Issue 42 (1-2008)
Abstract
Tillage is one of the important managing factors that can destroy or improve soil structure. Soil structure is affected by the machines and shape of the wheels. Field experiments were conducted at Hamadan Agricultural Research Station on a coarse loamy mixed mesic Calcixerolic Xerocrepts soil to measure and evaluate the effects of tillage and wheel-induced compaction on selected soil physical properties. Treatments included tillage methods (Moldboard Plow and Chisel Plow, (MP, CP)) performed using three customary tractors in Iran [John Deer (J), Romany (R) and Massey Ferguson ( MF) ]. Traffic zone and non traffic zone were other treatments. A split-plot design with three replications was used in a completely randomized arrangement of treatments. Soil samples were taken at the end of wheat growth season in traffic and non- traffic zone and from four layers and compared for bulk density (BD), cone index (CI), and mean weight diameter (MWD). The influence of both tillage methods on BD in most soil depths was not significant, meanwhile, BD was higher in the deeper layers. Wheel traffic did not affect BD significantly, but its effect decreased by increasing the depth. Commonly, conservation tillage increased structural stability as evaluated by MWD. Cone index illustrated the same trend as for BD, with some variation because of it higher sensitivity, so it was significantly was increased in CP rather than in MP for the traffic zone. Such a difference was not observed in non-traffic zone. The CI was also significantly increased in traffic zone compared with non-traffic zone. J significantly increased CI in two first layer in comparing with MF, but there was not significant difference between J and R. The MWD was increased by chisel plow in non-traffic zone and this increment was significant in fourth soil layer (22.5- 30 cm). Wheel traffic caused the increase of MWD in the second layer and significant difference was not observed in other layers. Overall, R caused less destruction in soil structure and tillage methods changed some of soil physical properties.
Z Daneshvar Ran, M Esfahani, M Payman, M Rabiei, H Samie Zadeh,
Volume 12, Issue 46 (1-2009)
Abstract
The effects of tillage methods and residual management on yield and yield components of rapeseed (Brassica napus L. CV. Hyola308) were evaluated after rice harvest. The experiment was carried out during 2004-2005 cropping season in a factorical arrangement of treatments at Rice Research Institute of Iran (RRII) in Rasht, in a Complete Randomized Block Design with three replications. Treatments included tillage in three methods: a) conventional tillage b) minimum tillage, and c) no tillage, and rice residue management in two manners: a) removing residues, and b) not removing residues. Plant traits such as grain yield, oil percentage and yield, plant density, plant height, the lowest pody branch height from soil surface, number of pods per plant, plant and weed dry weight, leaf area index (LAI) and crop growth rate (CGR) were measured. Results indicated that grain yield was affected by the tillage type. Also, the effect of tillage type on plant height, number of pods per plant, the lowest pody branch height from soil surface, and oil yield was significant. The effect of residual management and residual management interaction and tillage were significant on none of the traits except for weed dry weight. Economic analysis indicated that rapeseed planting in a field with rice residual and minimum tillage had a relative advantage of less production cost in spite of nearly 15 percent yield decrease compared to other methods.
E Dehghan, M Almasi,
Volume 13, Issue 47 (4-2009)
Abstract
Soil tillage management for various crops in different regions needs use available indices and information about condition, manual manner, defects and preferences of various tillage methods. Therefore, this experiment was conducted in summer 2003 on clay soil containing wheat residual in Shawoor agricultural research center, situated in northern Ahwaz. Experiment was conducted as a Randomized Complete Block Design (RCBD). Treatments included: conventional tillage in one pass of moldboard plowing in 20cm depth + leveler (T1), two passes of disk harrow in 8-10cm depth + leveler (T2), two passes of disk harrow in 12-15cm depth + leveler (T3), one pass of cultivator in 10cm depth + leveler (T4), one pass of cultivator in 15cm depth + leveler (T5) and one pass of rotivator in 5cm depth (T6). The results showed that fuel consumption decreased for T2-T6 57, 51, 67, 54 and 69 % as compared to T1 (49 L/ha), respectively. Total operation time decrease in T2-T6 42, 46, 42, 54 and 44 % in comparison to T1 (4.41 h/ha) respectively. Field capacity increased for T2-T6 as much as 2.4, 2.2, 2.4, 1.8 and 2.3ha/h compared to T1, respectively. Mean weight diameter (MWD) index increased in T2-T5 29, 21, 10 and 5 % than T1 (1.92cm), respectively, but decreased 6% in T6. Mean tillage costs reduced in T2-T6 as much as 40, 32, 54, 50 and 60 % compared to T1 (500000 Rial/ha), respectively.
H Shirani, M.a Hajabbasi, M Afyuni , A Hemmat ,
Volume 14, Issue 51 (4-2010)
Abstract
Tillage systems and organic manures could affect soil physical and mechanical properties. This study was conducted to investigate the impacts of two tillage systems including conventional tillage by moldboard plowing (plowing depth, 30 cm) and reduced tillage by disk plow (plowing depth, 15 cm) and three rates (0, 30 and 60 ton ha-1) of farmyard manure (FYM) on the soil penetration resistance under corn cropping in a split block design with 3 replications. The cone index (CI) decreased with increase of the tillage depth. It is attributable to soil disturbing and loosening of the deeper layers under conventional tillage compared to reduced tillage. This trend, however, was observed only in the first (after treatments’ application and before cropping) and second (the highest rate of vegetative growth) samplings. In the third sampling (after harvest), there were not significant differences between the CI values under two tillage systems in different soil depths. It might be due to soil re-compaction (approaching the pre-tillage state) as well as disappearance of the tillage effects seven month after commencement of the experiment. In fact, the soil mechanical resistance increased with the time indicating soil re-compaction over the growing season. Adding FYM to the surface layer (i.e. 0-10 cm) of ridge soil resulted in significant decrease of soil mechanical resistance compared to control treatment. The CI decreased significantly in the 30 ton ha-1 treatment up to the stage of highest rate of vegetative grow, but the effect on CI was diminished after harvest. However, the decreasing effects of the 60 ton ha-1 treatment on the CI continued to the harvesting time. There were no significant effects of FYM in the soil deeper than 10 cm from the ridge surface and in all of the layers in furrow. The CI did not decrease significantly in the furrow due to negligible effect of manure application for the inter-row position.
A. Heydari,
Volume 15, Issue 57 (10-2011)
Abstract
Performance of proper deep tillage can reduce negative effects of soil compaction. The objectives of the research were to determine the effects of deep tillage application on soil physical properties and wheat yield. Therefore, in 2006-2007 an experiment was conducted at Tajarak Agricultural Research Station of Hamedan on a soil with clay loam texture. In this research, four tillage methods were used. These methods were: 1) subsoiling with 30cm soil depth + conventional tillage (moldboard plowing) 2) subsoiling with 50cm soil depth + conventional tillage, 3) plowing by combined plow (chisel plow + roller) with 30cm soil depth and 4) conventional tillage (plowing by moldboard plow to 25-30cm soil depth). Randomized complete block design with four treatments and replications was used to analyze data and compare the treatment means. Before and after the application of the tillage treatments, parameters of cone index, bulk density and infiltration rate were measured in soil. Also before yield harvesting, components of yield (grain number in panicle, panicle number in plant and 1000 grain weight) were measured. To measure grain yield in experimental plots, in each plot ten square meter area from the yield was harvested. Result indicated that effect of different tillage treatment on soil resistance was not significant. Effect of deep tillage methods on bulk density and infiltration rate was significant. Deep tillage methods increased water infiltration rate in the soil and decreased soil bulk density. Effect of different deep tillage methods on wheat yield was not significant. However, application of chisel plow increased the wheat yield by 25%. It may be concluded the subsoiling treatment does not affect the crop yield in intensive and fully irrigated field condition. The results of this study indicated that if there is a compacted layer at 30cm soil depth, and with the same climate and soil as those in the experimental site, the application of chisel plow due to economical consideration (low fuel consumption and high field efficiency) can be recommended for soil preparation and cultivation of irrigated wheat.
S. Yousefi-Moghadam, S. F. Mousavi, B. Mostafazadeh-Fard, M. R. Yazdani, A. Hemmat,
Volume 16, Issue 60 (7-2012)
Abstract
Puddling is the most common method of land preparation for lowland rice cultivation. The purpose of this study was to assess the influence of various intensities of puddling on percolation rate, water retention by soil and the amount of water used for different puddling intensities in three dominant soil textures of paddy fields in Guilan province. Undisturbed soil samples were taken from 3 different soils including silty clay, clay loam and loam, with 3 replications. The soil samples were puddled by a laboratory apparatus with different intensities. The results showed that the low puddling intensity treatment caused a 29.3, 32.4 and 36% reduction of percolation rate in silty clay, silty loam and loam textures, respectively. Increasing puddling intensity from low to medium reduced percolation rate significantly, but high intensity was not effective. Soil moisture characteristic curves of all three soils showed that water retention was increased by puddling treatments. Water retention in silty clay was higher than the other two soils. The high intensity treatment needed more water than low intensity for puddling. Increasing puddling intensity from medium intensity to high intensity caused 15.4, 14.1 and 16.3% increase in the amount of water required for puddling in silty clay, silty loam and loam textures, respectively. Generally, in all the three studied soil textures, the amount of water used for high-intensity puddling was more than medium-intensity puddling, while it had no significant effect on water percolation rate and soil water retention.
J. Asghari Meidani, E. Karimi, S. B. Mousavi,
Volume 16, Issue 60 (7-2012)
Abstract
This study was conducted to study and compare the effects of different tillage systems on soil physical properties and wheat yield in dryland conditions. The experiment was carried out in Maragheh Dryland Research Station with 5 treatments and 4 replications based on RCBD for 3 years (2001-2003). The results showed that difference between the treatments in terms of wheat yield was significant, and stubble chopping and chisel plow tillage in fall + sweep in spring + seed drill planting had the maximum yield (i.e. 1452 kg/ha), lower value for yield (1.077kg/ha) blonged to T1 treatment. Also the results showed that spike/plant and spike length were the main characters in yield increase. For the soil bulk density and water content, the difference between treatments was significant and in planting and flowering stages stubble chopping and chisel plow in fall + sweep in spring + planting by seed drill had the highest soil water content and the lowest bulk density
A. Heidari, A. Hemmat, S.m Rezvani,
Volume 18, Issue 67 (6-2014)
Abstract
efficiency was investigated during a 2-year period (2009-2010) in a silty clay loam soil in Tajarak Research Station
(Kaboudarahang Township), Hamedan. The experimental design was a strip-plot within a randomized complete blocks
design. The horizontal band, the irrigation water rate after flowering, included full and deficit irrigation (100% and 75%
potato water requirement) and the vertical band, kind of inter-planting row tillage including 1- subsoiling to 30-35 cm
soil depth, 2- chiseling to 20-25 cm soil depth, 3- sweeping to 5 cm soil depth and 4- no-till. During the growing
season, soil mechanical resistance (cone index) in two stages and water infiltration into the soil were measured. At the
end of the growth season (harvesting time), potato yield quantity and quality were measured. Result showed that the
effect of inter-row tillage on soil mechanical resistance was significant. Subsoiling and chiseling had lower soil
mechanical resistance and higher water permeability between treatments, respectively. The effect of inter-row tillage on
potato yield was significant so subsoiling and chiseling had a higher potato yield between treatments, respectively. The
effect of irrigation water rate on potato yield was not significant. The effect of inter-row tillage on water use efficiency
wasn’t significant.
E. Habibi, M. A. Asoodar, B. Khalil Mogaddam,
Volume 18, Issue 67 (6-2014)
Abstract
Extensive tillage leads to the degradation of soil structure and aggregate stability. The effects of three different tillage implements including (combination tillage, chisel packer and disk), three levels of soil water content including (0.5, 0.7 and 0.9 plastic limit), three working speeds including (6, 8 and 10 km/hr) and two soil textures including (loam and silty clay loam soils) were studied. The study was carried out in Khuzestan Ramin Agriculture and Natural Resources University, in 2011. Soil aggregate mean weight diameter (MWD), geometric mean diameter (GMD) as determined by wet sieving method and soil surface roughness (SSR) were measured. Results showed that chisel packer with 0.744 mm MWD produced largest soil aggregates in both soils because of using narrow blade and shanks and small rake angles compared to other tillage treatments. Soil aggregate size was shown larger than other tillage treatments where chisel packer was employed but it was not suitable because of deep furrow shapes. Combination tillage was able to make a better soil condition to be used for seeding where the experiment was conducted.
M. Hosseini, S. A. Movahedi-Neeni, M. Zeraat Pishe,
Volume 18, Issue 68 (9-2014)
Abstract
Effects of five various tillage systems on soil porosity, volumetric water content, diurnal and nocturnal soil temperatures, plant water uptake and dry matter yield was investigated using a completely randomized design with five treatments and four replications in Gorgan University of Agricultural Sciences and Natural Resources research farm located in Seyed-Miran during 2009-2010 growing season. Tillage systems were: moldboard plough followed by one discing (20-25 cm) rototiller (12-17 cm) double disc (8-10 cm) Chisel plow (25-30 cm) No-tillage. Results show that during all stages of wheat growth, the highest and the lowest soil porosities at 0-8 cm depth were obtained by moldboard plough and No-tillage treatments respectively. For all stages except before tillering and harvest, the highest soil porosity obtained by moldboard treatment at 8-16 cm depth. Increasing tillage intensity increased those porosity that keep water in potentials greater than -5 and those in potentials less than -15 bar. No-tillage and moldboard induced the highest and the lowest soil temperatures respectively before earring stage. Tillage intensification, increased soil porosity and root density. More roots reduced soil water content in response to increased water uptake by wheat, resulting greater dry matter accumulation.
J. Hamzei, M. Seyedi,
Volume 18, Issue 70 (3-2015)
Abstract
This experiment was carried out at the Agricultural Research Station of Bu-Ali Sina University to study the effect of different tillage methods on bulk density, yield, and yield components of barley (Hordeum vulgare) cultivars under rainfed conditions. Three levels of tillage (CT: conventional tillage, MT: minimum tillage and NT: no tillage) and five barely cultivars (V1: Local V2: AbidarV3: Valfagr V4: Bahman and V5: Makouei) were evaluated in a factorial arrangement in a completely randomized block design with three replications in the growing season of 2010-11. Traits of bulk density plant height, grain yield, yield components, biological yield, and harvest index (HI) were evaluated. The results showed that maximum value of bulk density (1.09, 1.26 and 1.29 g cm-3 for 0-10, 10-20 and 20-30 cm of sampling depth, respectively) was observed at MT treatment. But, there was no significant difference between MT and NT treatments for this trait. In comparison of cultivars, maximum bulk density was achieved with Valfagr cultivar. Using chisel plow (MT treatment) produced maximum plant height (70 cm) and yield components (513 numbers of spike m-2 and 19.2 grain spik-1). Also, among cultivars maximum plant height (72.7 cm) and grain number spike-1 (23.2 grain spike-1) belonged to Valfagr cultivar. Also, results showed that V3×MT treatment had the highest grain yield (3100 kg ha-1). Therefore, the findings of the study recommend using chisel plow (MT treatment) and Valfagr cultivar.
M. Marzi Nohadani, B. Mostafazadeh-Fard, S. F. Mousavi, M. R. Yazdani, M. R. Alizadeh,
Volume 19, Issue 72 (8-2015)
Abstract
The common method of puddling is using a conventional tiller which requires long time of soil operations.In this study, the effects of tillage equipment on moisture characteristic curve of a paddy soil were investigated. The treatments included tillage equipment (T1: conventional tiller, T2: rotary puddler, T3: cone puddler, T4: tractor mounted rotivator) and number of puddlings (P1: puddling once, P2: puddling twice, P3: three times'puddling and P4: four times'puddling). The results showed that at saturation point, tractor mounted rotivator presented the highest moisture content. At field capacity and permanent wilting point, the cone puddler showed the highest moisture value. The two newly made units held more moisture and saved water. In different tillage equipment, increasing the number of puddling reduced soil moisture. Available moisture in the soil without tillage (control) was less than in soils under rotary puddler and cone puddler.
A Heidari, H. Haji Agha Alizadeh, A. R. Yazdanpanah, J. Amiri Parian,
Volume 20, Issue 78 (1-2017)
Abstract
Traditionally, most corn field in Hamedan Province is prepared for planting by moldboard plowing followed by a number of secondary tillage operations. In recent years conservation tillage systems have become more popular. This research was conducted in the form of a split plot experimental design with six tillage treatments and three replications. Main tillage methods including: (T1) conventional tillage (moldboard plow + cyclotiller equipped with roller), (T2) combination tiller (chisel plow equipped with roller) (T3) bandary tillage with chisel blades were considered as main plots and two P fertilizer application including: (F1) fertilize broadcasting and (F2) fertilizer bandary placement were considered as sub plots. During growing seasons, soil mechanical resistance (cone index), soil bulk density and water infiltration in soil were measured. At the end of the growing season (harvesting time), corn yield and its components were measured. Results indicated that tillage methods and soil depth had a significant effect on the soil bulk density and cone index. The effect of tillage on water infiltration in soil was significant. The effect of P fertilizer application on corn yield was significant (P≤0/01) and P fertilizer bandary placement with mean corn yield of 10862 kg/ha had higher yield value than the fertilizer broadcasting with mean corn yield of 9965 kg/ha. Although the difference between tillage methods for corn yield was not statistically different, T2 treatment with mean corn yield of 10913 kg/ha had higher yield value than the other two tillage treatments (T1 with mean corn yield of 10106 kg/ha and T3 with mean corn yield of 10222 kg/ha).
