Showing 6 results for Brazing
M. Amelzadeh, S. E. Mirsalehi,
Volume 2, Issue 2 (11-2016)
Abstract
Nowadays, cemented carbides-steels joints by brazing method are taken into consideration. One of the problems of these joints is the creation residual stresses that can reduce it with choose correct parameters of brazing. In this study, Silver base alloy filler containing copper, zinc and cadmium have been used in temperature 780°C and the effect of time parameter 5, 10 and 15 minutes on microstructure and mechanical properties were investigated. The results indicated that brazing in 15 minutes causes a columnar growth of solid solution phase of copper from cemented carbide side to steel and provides maximum strength of 94MPa. As well as, by passing of time wetting angle of cemented carbide surface reduces from 40° to about 27°.
M. Sameezadeh, M. Vaseghi, H. Zafari,
Volume 5, Issue 1 (9-2019)
Abstract
In this paper, failure mechanism of a 17th stage blade of an 82.5 MW steam turbine that caused damage to the internal turbine compartment and the adjacent blade equipment has been studied. In order to determine the cause of failure and prevent similar events, various metallurgical and mechanical investigations including chemical composition analysis, metallography and microstructural analysis, fractography using scanning electron microscope and hardness and tensile tests were carried out. The initial results showed that the alloy had a chemical composition, microstructure and mechanical properties in the acceptable range, and the fracture failure was not due to the mechanical and metallurgical degradation during the service. The results of the fractography indicate high cycle fatigue as the main mechanism of the failure and shows that the fatigue crack has initiated from the adjacent hole relative to the vibration damped wire near to the brazing region on the blade, due to inadequate quality and incomplete connection of the brazing and its stress concentration effect the hole, which eventually has propagated and reached a critical level, and a sudden failure of the blade has occurred.
S. A. A. Hashemi Milani, R. Tavangar, M. Azadbeh, Kahinpoor, H. Sadeghi-Nasab,
Volume 6, Issue 1 (8-2020)
Abstract
During the brazing of aluminum-based heat exchangers, the flux dry-off temperature plays a crucial role to get sound joints with maximum strength. In the present study, the NOCOLOK® flux consists of two phases of K2AlF5.H2O and KAlF4 with a melting point around 580 °C was used for brazing AA3003 as base metal with a clad-coating of AA4343 as filler metal. The slurry was applied on the joints and they dried at 220, 300 and 380 °C in air. The tensile shear test revealed that when the slurry dried at 300 °C, the joint withstand maximum shear stress of 44 MPa without defective features. At 220 °C and 380 °C, joint shear stresses were 34 MPa, 30 MPa respectively. However, drying at 380 °C under protective nitrogen gas enhanced the shear strength of up to 39 MPa. Having applied a change in current dryer temperature in the factory from 360 °C to 300 °C reduced the percentage of heat exchangers leakage from 3.2% to 0.6%, approximately, on a weekly basis.
E. Mansouri, H. Khorsand,
Volume 9, Issue 2 (1-2024)
Abstract
High entropy alloys are especially suitable for use as filler metals in brazing due to their excellent properties. in the present study, three powders with the composition of CoxCrxCuxFexMnxNix (X atomic percentage of the element) were designed using the criteria of these alloys as well as jmatpro software. in the next step, using mechanical alloying, filler nano powder was synthesized and characterized by X-RAY analysis (XRD) test and the effect of filler composition on the thermal behavior of the alloy was studied. then the filler was used in Inconel 600 super alloy brazing, the single-phase solidification behavior and the absence of boron and silicon in the high entropy filler led to the creation of a continuous microstructure without eutectic components or brittle phases in the brazing interface. thus, the shear strength test was performed and 545 MPa was the highest shear strength obtained among the three filler compounds. in brazing conventional filler metal, incomplete isothermal solidification and subsequent thermal solidification of the residual liquid results in large grains of chromium-rich boride phase distributed throughout the microstructure. not using compounds that lower the melting point in the filler for the purpose of joining the nickel-based superalloy is considered an important step in reducing the subsequent brazing processes.
A. Ardalani, H. Naffakh-Moosavy,
Volume 9, Issue 2 (1-2024)
Abstract
In this research, the effect of temperature and time parameters are investigated on the microstructure and mechanical properties of dissimilar brazing of 17-4 PH stainless steel and Ti-6Al-4V alloy with BNi-2 filler metal. The microstructure of the joint is evaluated with optical and scanning electron microscopes and the mechanical properties of the joint are also evaluated with tensile-shear and microhardness tests. It can be seen that at a constant temperature of 1050°C, increasing the time from 15 to 30 minutes decreases the shear strength from 34.66 to 29.39 MPa. Formation of brittle intermetallic compounds like NiTi2 and FeTi2 increase strength and promote brittle fracture.At a fixed time of 15 minutes, increasing the temperature from 1050 to 1100 °C causes the strength to increase from 34.66 to 38.46 MPa. Also, the increase in temperature and time increases the ISZ thickness formed in the joints on the side of the filler metal - Ti-6Al-4V from 41.40 to 81.48 microns. The increase in temperature and time also causes more diffusion of boron into the SS-filler joint, which forms various boron compounds and widens this region.
M. Taheri, Gh. Azimiroeen, M. Shamanian, A. Bahrami,
Volume 10, Issue 1 (6-2024)
Abstract
The dissimilar joint of alumina to copper with active filler metals Ag-Cu-Ti-Sn and Ag-Cu-Ti-Sn-%3.5Zr were done using the induction brazing process at temperatures of 840 and 860 ℃ for 15 minutes. The microstructures of joints were evaluated using optical microscope (OM) and scanning electron microscope (SEM). Vickers hardness test and shear tensile strength test were used to evaluate the mechanical properties. The results of the microstructural studies showed that the Al2O3/Cu joints using Ag-Cu-Ti-Sn and Ag-Cu-Ti-Sn-%3.5Zr fillers contain a reaction layer at the interface between alumina and the filler metal. At the area of the reaction layer with Ag-Cu-Ti-Sn filler metal, two TiO and Cu3Ti3O phases were observed, and also at the reaction layer with Ag-Cu-Ti-Sn-%3.5Zr filler metal, two TiO and ZrO2 phases were observed. The results of the shear strength test showed that due to the greater thickness of the filler metal and the lower thickness of the reaction layer, the joint with the filler metal Ag-Cu-Ti-Sn-%3.5Zr (14 MPa) has a higher shear strength as compared with the joint with filler metal Ag-Cu-Ti- Sn (9 MPa).
