Showing 6 results for Filler Metal
M.r. Samadi, H. Mostaan, M. Rafiei , M. Salehi,
Volume 6, Issue 1 (8-2020)
Abstract
Nowadays, aluminum and its alloys have extensive applications in marine and aerospace industrious owing to their excellent properties. Among these alloys, 5xxx series of aluminum alloys have also excellent corrosion resistance, high toughness and strength and also good weldability. Decrease in yield strength and also tensile strength due to the grain growth in the heat affected zone is of the main problems in the welding of these series of Al alloys. In this research work, gas tungsten arc weld joints in two modes i. e. direct current and pulsed current were compared in order to study the effect of this parameter on the microstructure, mechanical properties and corrosion resistance of weld joints. Also, the effect pulsed current parameters such as peak current and basic current were investigated. Microstructural evolutions and fracture surfaces of weld joints were examined by optical microscope and scanning electron microscope, respectively. It was found that the fracture behavior of all joints is in a ductile manner. Also, tensile test and electrochemical polarization were conducted in order to study the mechanical properties and corrosion behavior of weld joints.
M. M. Taghvaei, H. Mostaan, A. Sonboli, H. R. Mansouri Gavari,
Volume 8, Issue 1 (8-2022)
Abstract
In this study, DIN 34CrAlNi7 Nitriding steel in two states before and after nitriding, were welded by tungsten-gas arc welding process using two types of fillers (ER309L and ER312). The aim of this research was to investigate the best conditions for welding (before or after nitriding) and also to choose the best filler metal. The microstructure of the joint was examined using an optical microscope. A tensile strength test was also used to evaluate the mechanical properties. Fracture surfaces were also studied using a scanning electron microscope (SEM). According to the results Welding of these steels with ER309L filler is allowed only in the pre-nitriding state. If the base metal is nitriding, due to microstructural changes in the weld metal, filler metal ER309L cannot be used. However, the results of samples welded with ER312 filler metal show that if the base metal mixing percentage is less than 30%, this filler can be used for welding base metals in both before and after nitriding.
S. Varmaziar, M. Atapour, Y. Hedberg,
Volume 8, Issue 1 (8-2022)
Abstract
The influence of filler metals on the microstructure and corrosion behavior of AISI 316L welds was investigated. Gas Tungsten Arc welding (GTAW) process was applied to join the AISI 316L plates using ER 316L and ER 312 filler metals. The obtained microstructures were characterized by optical metallography and scanning electron microscope (SEM). Corrosion assessments were conducted in 3.5% NaCl using a three electrode cell. Open circuit potential and potentiodynamic polarization examinations were conducted on the welds and base metal. Microstructural evaluations indicated that a combination of austenite and ferrite phases was formed in the welds fabricated by both filler metals. Based on the micro hardness tests, the weld fabricated by ER 312 filler exhibited superior harness compared to the ER 316L weld. Corrosion evaluations also show that the weld metal obtained from two filler metals has a lower corrosion rate due to the higher amount of chromium and higher ferrite compared to the base metal. Also, the lower corrosion current of ER 312 weld metal compared to ER 316L weld metal is for this reason. In contrast to the base metal compared to the two welding metals, the result of the two filler metals has shown better pitting corrosion results according to the electrochemical tests and also the examination of the surfaces using an optical microscope after these tests, that these results are due to The presence of two phases of austenite and ferrite in the vicinity of each other in weld metals and the intensification of galvanic corrosion is due to the discharge of the austenite phase from chromium and molybdenum.
M.m. Jafari, A. Afsari, S.a. Behgozin, Sh. Heidari,
Volume 8, Issue 2 (1-2023)
Abstract
In this study, the mechanical and tribological properties of 4 different types of welding filler metals were examined on a 1.6959 steel (DIN35NiCrMoV12-5) by the Gas Tungsten Arc Welding process. The fillers used in this study include ER70S-6, ER80S-G, ER80S-Ni1, ER80S-B2. The main reasons for choosing these fillers in this study are their availability and close chemical composition to the base metal. To evaluate the weld and quality of weld joints, tensile, impact, hardness and abrasion tests performed on the samples and related microstructures was investigated by optical microscope. The results indicated that the presence of molybdenum and chromium alloying elements in ER80S-B2 filler and related microstructure at HAZ has led to an increase in weld strength up to 38 percent. The best and worst wear resistance obtained from the filler ER 80S-Ni1 and ER 70S-6 respectively. The best weld quality and mechanical properties were acquired in welding using ER 80S-B2 welding filler metal.
E. Mansouri, H. Khorsand,
Volume 9, Issue 2 (1-2024)
Abstract
High entropy alloys are especially suitable for use as filler metals in brazing due to their excellent properties. in the present study, three powders with the composition of CoxCrxCuxFexMnxNix (X atomic percentage of the element) were designed using the criteria of these alloys as well as jmatpro software. in the next step, using mechanical alloying, filler nano powder was synthesized and characterized by X-RAY analysis (XRD) test and the effect of filler composition on the thermal behavior of the alloy was studied. then the filler was used in Inconel 600 super alloy brazing, the single-phase solidification behavior and the absence of boron and silicon in the high entropy filler led to the creation of a continuous microstructure without eutectic components or brittle phases in the brazing interface. thus, the shear strength test was performed and 545 MPa was the highest shear strength obtained among the three filler compounds. in brazing conventional filler metal, incomplete isothermal solidification and subsequent thermal solidification of the residual liquid results in large grains of chromium-rich boride phase distributed throughout the microstructure. not using compounds that lower the melting point in the filler for the purpose of joining the nickel-based superalloy is considered an important step in reducing the subsequent brazing processes.
M. Taheri, Gh. Azimiroeen, M. Shamanian, A. Bahrami,
Volume 10, Issue 1 (6-2024)
Abstract
The dissimilar joint of alumina to copper with active filler metals Ag-Cu-Ti-Sn and Ag-Cu-Ti-Sn-%3.5Zr were done using the induction brazing process at temperatures of 840 and 860 ℃ for 15 minutes. The microstructures of joints were evaluated using optical microscope (OM) and scanning electron microscope (SEM). Vickers hardness test and shear tensile strength test were used to evaluate the mechanical properties. The results of the microstructural studies showed that the Al2O3/Cu joints using Ag-Cu-Ti-Sn and Ag-Cu-Ti-Sn-%3.5Zr fillers contain a reaction layer at the interface between alumina and the filler metal. At the area of the reaction layer with Ag-Cu-Ti-Sn filler metal, two TiO and Cu3Ti3O phases were observed, and also at the reaction layer with Ag-Cu-Ti-Sn-%3.5Zr filler metal, two TiO and ZrO2 phases were observed. The results of the shear strength test showed that due to the greater thickness of the filler metal and the lower thickness of the reaction layer, the joint with the filler metal Ag-Cu-Ti-Sn-%3.5Zr (14 MPa) has a higher shear strength as compared with the joint with filler metal Ag-Cu-Ti- Sn (9 MPa).
